Oreck XL3610HH To Replace Filter Dust Bag, How to Replace a Worn Belt, To Adjust or Replace Brush

Page 6

E N G L I S H

CAUTION—Wood Floors, Soft (Vinyl, Asphalt Tile, etc.) Floor Surfaces and Polished Floor Finishes

Use floor and floor finish manufacturer’s recommended methods of cleaning. The metal strip on the base of the cleaner could be damaged if used on concrete or abrasive surfaces, and, therefore, cause damage to wood floors, soft (vinyl, asphalt tile, etc.) floor surfaces and polished floor finishes. The roller brush may also scuff very soft finishes. Do not operate the unit while in the upright and locked position. Do not let the unit run while in any one stationary position for any period of time. Keep the unit moving while in operation.

XL3600HH: Celoc® Hypo-Allergenic Filter System

The Celoc SMMS outer bag of your vacuum cleaner is high filtration medical material designed to filter the smallest of dust particles. It is important the inside of the outer bag be cleaned. Vacuum the inside of the outer bag or hand wash, turned inside out, with warm water, and air dry. For best results, the Celoc SMMS outer bag should be replaced once a year. The Celoc layered disposable inner dust bag must be replaced once a month even if it is not full. Change it more often if it is used in extremely dirty areas. Increase the cleaning power of your vacuum by changing the bag often.

To Replace Filter Dust Bag

WARNING: Unplug cord from electrical outlet before servicing.

BAG REMOVAL:

fig. 7 Unzip outer bag completely.

fig. 8 Pull bag cardboard collar to release bag dock door from

connector. Bag dock door will hinge downward.

fig. 9 Gently pull bag cardboard collar upward out of the bag dock. The dust seal will close automatically.

BAG INSTALLATION:

fig. 10 Slide the cardboard collar completely onto bag dock door.

fig. 11 Firmly push bag dock door with both thumbs on indication point until it snaps.

How to Replace a Worn Belt

WARNING: Unplug cord from electrical outlet before servicing.

fig. 12 Remove the replacement belt from the storage channel.

fig. 13 Remove the door by removing the hold down screw located on side of power head.

fig. 14 Slide the door forward by prying open with a screwdriver or coin. fig. 15 Remove the belt from the motor drive shaft and brush roll pulley.

fig. 16 Loop the new belt over the motor drive shaft. Place the opposite end of the belt on the brush roll pulley. Rotate the brush roll three (3) complete revolutions to ensure that no part of the belt is overhanging the end of the motor drive shaft.

fig. 14 Replace the door by sliding it into the groove at the bottom of the housing.

fig. 13 Replace the hold down screw and tighten.

To Adjust or Replace Brush

WARNING: Unplug cord from electrical outlet before servicing.

fig. 17 To determine if the brush is worn, place a firm straight edge across the nozzle opening. If brush bristles do not extend beyond baseplate, brush should be adjusted.

fig. 18 Remove the baseplate by removing 5 screws. fig. 19 Remove the belt and brush roll from the housing.

fig. 20 Rotate both bearing assemblies at ends of brush roll to show "OLD" and replace in the holding channels in the housing.

NOTE: The bearing assembly setting marked "OLD" has no ribs on the top of the assembly. The one marked "NEW" has several ribs. When

5rotating bearings, make sure both bearing assembly settings are the same and face up when replacing the brush roll.

Page 5 Page 7
Image 6
Page 5 Page 7
Contents XL3600HH XL3610HH OLD Accessories Sold Separately Table of ContentsMaintenance and Customer Service Polarized Plug NoticeNot plugged Be sure cleaner is WarrantyTroubleshooting Guide Filter bag is full Replace filter bagOperating Instructions Parts ListAssembly General InformationHow to Replace a Worn Belt To Adjust or Replace BrushTo Replace Filter Dust Bag Table des matières Entretien et service à la clientèleAccessoires Vendu Séparément Avis de fiche polariséeImportantes GarantieListe de pièces Mode d’emploiGuide de dépannage Assemblage3Remplacement du sac à poussières filtrant Remplacement d’une courroie uséeInformations générales Utilisation d’une tablette Oreck Fresh Air Réglage ou remplacement du balaiRemplacement de l’ampoule électrique Blocage ou bourrageAviso de la clavija polarizada IndiceMantenimiento y servicio a clientes Accesorios Vendido por separadoDE Seguridad GarantíaEnsamblaje Guía para identificación de problemasLista de piezas Instrucciones de operaciónInformación general Para reemplazar la bolsa para polvo de filtroCómo reemplazar una correa desgastada Reemplazo de la bombilla Para ajustar o reemplazar el cepilloUso de una tableta Oreck Fresh Air Relleno o bloqueo

XL3600HH, XL3610HH specifications

The Oreck XL3610HH and XL3600HH are two advanced upright vacuum cleaners that epitomize modern cleaning technology. Designed for both efficiency and ease of use, these vacuums are ideal for households seeking potent performance combined with lightweight maneuverability.

One of the standout features of the Oreck XL series is its impressive suction power. Both models utilize a high-speed roller brush that spins at an incredible rate, engaging carpet fibers deeply and lifting dirt as well as debris effectively. This makes them particularly effective on various floor types, including carpets and hard floors.

Another remarkable aspect of the Oreck XL3610HH and XL3600HH models is their weight. Weighing in at only 8 pounds, they are significantly lighter than many competitors, making them easy to carry and maneuver. The simple, ergonomic design allows for comfortable operation, reducing fatigue during prolonged cleaning sessions.

Both models are equipped with a unique Saniseal technology. This feature allows for the automatic sealing of the vacuum bag when it is removed, preventing dust and allergens from escaping back into the environment. Consequently, users can enjoy cleaner air quality, which is particularly beneficial for allergy sufferers.

The XL3610HH comes with an additional HEPA inner bag, adding an extra layer of filtration. This advanced filtration system captures 99.97% of particles as small as 0.3 microns, including pollen, dust mites, and pet dander. This characteristic makes it an outstanding choice for pet owners and individuals sensitive to allergens.

With regard to versatility, both models feature an impressive range of attachments and tools. These include a dusting brush, crevice tool, and upholstery nozzle, enhancing cleaning capabilities for various surfaces and areas around the home. The long power cord allows for extended reach, minimizing the need to frequently change outlets during cleaning.

Durability is another hallmark of the Oreck brand. Engineered with robust materials, the XL3610HH and XL3600HH are built to withstand the rigors of daily use, ensuring reliability over time.

In conclusion, the Oreck XL3610HH and XL3600HH embody a blend of powerful performance, lightweight design, and advanced filtration technology, making them exemplary choices for anyone in search of an efficient upright vacuum. Whether destined for carpets or hard floors, these vacuums provide thorough cleaning and superior convenience for everyday household cleaning needs.
Top Page Image Contents