Operating Instructions
To Operate
Make sure the disposable paper filter dust bag is in place. DO NOT operate the cleaner without a paper filter dust bag. Plug the power cord into an electrical outlet.
Press the ON(l) - OFF(O) switch on handle assembly when ready to operate.
General Information
The performance of your new cleaner greatly depends upon care and maintenance. The instructions in this manual will guide you in performing basic care and maintenance. To obtain the most satisfying years of service, read the instructions and keep them handy for future reference.
Operating Recommendations
This new ORECK XL
The following are a few simple suggestions regarding its operation:
1.When inserting a new disposable paper filter dust bag— FIRST PUFF OUT and OPEN THE BAG.
2.When the disposable filter dust bag is full, REPLACE IT.
3.If at any time the machine does not pick up properly or makes an unusual noise, STOP OPERATION and service.
4.Although your upright will pick up pins, paper clips, and other small objects, it is recommended that these be removed from the floor before you vacuum. Failure to do so may result in permanent damage to the motor suction fan and its housing.
5.WARNING: Do not use your vacuum cleaner on damp or wet surfaces. This will cause damage to the vacuum cleaner and is dangerous to the user. Damage caused by use on wet or damp surfaces is not covered under warranty.
6.REPLACE THE BELT EVERY 6 MONTHS.
7.Change the disposable filter dust bag at least once a
8.Do not run the vacuum cleaner over cord. The revolving brush could damage the cord.
9.Use caution when vacuuming over area rug edges and fringe.
Disposable Paper Filter Dust Bags
Disposable paper filter dust bags play a very important role in the efficiency of your ORECK vacuum cleaner. The purpose of the paper bag is to trap dirt, but at the same time it must be porous enough to allow air to pass through. If the paper bag becomes clogged, no air can pass through the cleaner and cleaning cannot take place, regardless of the cleaner’s power.
To keep your cleaner operating at maximum efficiency, change the dust bag frequently. DO NOT FILL ABOVE THE LINE INDICATED ON THE DUST BAG.
Be sure the disposable paper filter dust bag is in proper position, over the lower lip and the top lip of the connector.
All paper dust bags are not the same. Your ORECK disposable dust bags have been designed to be used with the ORECK cleaner. Using bags other than genuine ORECK disposable bags will affect the cleaning ability of your cleaner and could cause damage to it.
The Belt
The belt on your vacuum cleaner controls the speed of the revolving brush and is very important for the effective operation of the cleaner. If the belt becomes stretched or cut, it will cause the revolving brush to stop completely or slow down. See instructions in the manual for replacing belt.
An extra belt is stored in the baseplate of your cleaner. When buying replacement belts, use ONLY ORECK genuine belts. Belts other than ORECK belts will not operate the revolving brush correctly and may create undue stress which will cause damage to the motor and brush bearings. Using belts other than ORECK belts will void the warranty.
Lubrication
The vacuum cleaner motor bearings are factory lubricated and sealed. Further lubrication is not required.
General Cleaner Care
At least once a month, check revolving brush for excessive lint, string or hair. Remove this material.
Wipe the inside and outside of the outer vinyl bag and the
outside of the cleaner with a
damp cloth. Also clean the connector deflector assembly
area, base of cleaner and fan
housing area. If there is dust
in the outer bag, vacuum it or shake it out.
A little preventative maintenance will keep your cleaner looking new and will ensure continued cleaning effectiveness.
Cord Strain Relief
The cord strain relief located on the upper section of the handle is designed to reduce stress on the cord at the base of the handle.
Should the power cord come
loose from the cord strain
relief, it can be easily
reattached.
To attach the power cord to
the cord strain relief, grasp the
power cord approximately 12 
Clamp inches from the base of the
handle. Pinch power cord together and slide approxi- mately
5excess until the power cord is tightly rested under clamp.