Weil-McLain Radiant Heater manual Tube Layouts for Radiant Heating, Radiant Floor Heatng

Page 4

AlumiPex Radiant Tubing

A. Tube Layouts for Radiant Heating

1.Radiant Floor Heatng

a.Hot water flowing in the radiant tubing under the finished flooring heats the flooring and the heat emission plates. The heat emission plates help spread the heat evenly across the flooring.

b.Heat must pass through the flooring and the coverings on the floor (low pile carpeting and thermal pads, for example). See Figure 1.

The more the flooring and coverings act as insulators, the higher the tube water temperature has to be to cause the floor surface to heat up.

Heavy carpeting and pads resist heat transfer and are not recommended for use in radiant floor heating.

c.Heat will also try to move downward.

In suspended floor applications, heat will try to pass to the space underneath. So insulation is needed under the floor to prevent this heat movement.

Figure 1 - Heat flow from tube through slab

Carpet

Pad

Subfloor

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Heat Emission Plate

 

 

 

 

Tube

Sleepers

 

 

 

Sleepers

Subfloor

InsulationJoist

3.Radiant Floor Heating Design

a. The heating system designer must determine:

2.Heat Output from Radiant Floors

a.The floor surface is usually heated to a maximum temperature of about 85 oF - the surface temperature of human skin.

Higher floor temperatures in occupied areas could be uncomfortable.

Floor surface temperatures up to 92 oF are often used around the outside perimeter of rooms and in other areas where foot contact is limited.

b.The heat given off by the floor depends on the difference between the room temperature and the floor temperature - the larger the difference in temperature, the greater the heat.

With the floor at 85 oF and room temperature at 70 oF, each square foot of the heated floor will give off about 30 Btu’s per hour.

c.The spacing of tubes affects how much heat can be moved through the floor.

Closer spacing increases the heat per square foot of floor.

This is why tubes are often spaced closer together along outside walls with high heat losses - like next to large windows or patio doors.

The heat loss for each room.

Square feet of room floor surface available for floor heating.

The water temperature in the tubing and spacing between tubes - to match the heat given off by the floor to the heat lost from the room.

4.Tube Layout Patterns

a.The routing of the tubing in the room affects room comfort and effectiveness of the floor heating system.

b.Figure 2 shows typical tube layouts for above floor installations.

Where possible, the hottest water is usually routed along the outside walls.

Tube routing in above floor installations is limited by the practicality of variations in sleeper layouts. Sleepers are the boards used to separate the tubing and support the flooring.

c.Where the outside wall loss is particularly high, such as caused by patio doors, the tubing will sometimes be spaced closer together for a few feet out from the wall as shown in Figure 2.

b.Pay close attention to the key information given in these illustrations, such as:

• flow direction

• minimum bend diameters

• spacing to walls

• heat emission plates

• passage under walls

• use of closer spacing

4

Part Number 650-000-221/0298

Image 4
Contents AlumiPexÆ Hazard Definitions Codes and StandardsAlumipex STEP-BY-STEP Above Floor Installation Tube Layouts for Radiant Heating Radiant Floor HeatngRadiant Floor Heating Design Heat Output from Radiant FloorsAbove Floor Installation UT Y Obtain Tube Layout Drawing Floor Plan/Layout ShouldMeet with General Contractor Obtain Materials AlumiPex TubingAlumiPex Tube Fittings AlumiPex ManifoldsObtain Special Equipment AlumiPex Reamer/SizersTubing Uncoiler Pressure GaugePre-Installation Check List Mark Floor Plan and Tube Layout on SubfloorAttach the manifold to a plywood panel Mount ManifoldsPrepare holes for tube routing Manifold Mounting Install the Tubing Sleeper Layout Above Floor Above Floor Installation Pressure Test the Finished Tubing Installation Make a record of your installation Connect System Piping & Heating System ComponentsPressurize Tubing for Observation Before Leaving the JobsiteInspect Tubing Before Finished Flooring Installation Inspection, Repair and TroubleshootingAlumiPex Radiant Tubing

Radiant Heater specifications

Weil-McLain Radiant Heater is a standout choice for homeowners seeking efficient and reliable heating solutions. Renowned for its impressive energy efficiency and sleek design, it offers an array of features that cater to both comfort and performance.

One of the primary characteristics of Weil-McLain Radiant Heaters is their ability to provide consistent warmth. Utilizing radiant heat technology, these heaters warm up surfaces in a room, creating a cozy environment that feels comfortable from the moment you enter. Unlike traditional forced-air systems, radiant heating eliminates cold drafts, ensuring even heat distribution throughout the space.

A prominent feature is the use of high-quality materials in the construction of the heater. Weil-McLain employs durable, corrosion-resistant components that enhance the unit's longevity and reliability. This ensures that homeowners can enjoy consistent performance over many years, reducing the need for frequent repairs or replacements.

Weil-McLain offers a variety of sizes and configurations, making it easy for homeowners to find a model that fits their specific heating needs. Whether heating a small bathroom or a large living area, there is a radiant heater designed to excel in various applications. Additionally, many models come equipped with advanced thermostatic controls, allowing users to set and maintain their desired temperature easily.

Efficiency is a critical aspect of Weil-McLain Radiant Heaters. Designed to operate with minimal energy consumption, these heaters often exceed industry standards for efficiency, allowing homeowners to save on heating costs while enjoying optimal comfort. Many units are compatible with modern smart home technology, enabling remote monitoring and control for added convenience.

Furthermore, the aesthetic appeal of Weil-McLain Radiant Heaters cannot be overlooked. With their modern design and clean lines, they can seamlessly integrate into any home décor. Unlike bulkier heating systems, these heaters can be discreetly installed, enhancing the room's overall ambiance while providing the warmth needed during colder months.

In summary, the Weil-McLain Radiant Heater stands out for its ability to deliver comfortable, efficient heating. With durable construction, smart technology integration, and a variety of sizes, it meets the diverse needs of today's homeowners, ensuring warmth and comfort for years to come. That's what makes it a top choice in the world of home heating solutions.