Heath Zenith 5310 manual Installation, Wire the Light Control, Mount the Light Control

Page 2

INSTALLATION

Caution: Risk of fire. This fixture is designed for wall mounting only. DO NOT install on a ceiling or soffit.

For easy installation, select an existing light with a wall switch for replacement.

❒ Attach the lamp arm to the backplate arm and secure with the long bolt.

Note:When tightening the arm screw, pull on the wires to make sure the wires are not pinched by the joint.

❒ Drill out the holes if needed to mount the backplate to the junction box.

Wire the Light Control

WARNING: Turn power off at circuit breaker or fuse.

❒Remove the existing light fixture.

❒The S-hook can be used to hold the fixture while wiring. The small end of the hook can be inserted into a hole in the junction box. The large end goes around the “neck” of the fixture.

❒Route the light control’s wires through the large hole in the gasket.

❒Twist the junction box wires and fixture wires together as shown. Secure with a wire connector.

Black to Black

Cover Plate

Gasket

Mount the Light Control

❒Align the light control cover plate and cover plate gasket and the junction box. Insert and tighten the mounting screws.

❒If not installed on a weatherproof box or if an adaptor plate is used, caulk the wall plate and mounting surface with silicone weather sealant.

+/- 4°

MOUNT HORIZONTALLY

The halogen light must be mounted horizontally (+/- 4°).

Bulb Installation and Re-lamping

❒When re-lamping, turn power off and let the fixture cool.

CAUTION to avoid fire or burn hazards:

•Allow fixture to cool before touching.The bulb and fixture operate at high temperatures.

•Keep fixture at least 2" (51 mm) from combustible materials. Do not aim at objects closer than 3 feet (1 m).

•Re-lamp with type T halogen, 500 W max., 120 VAC lamp only.

❒Remove glass cover and remove the old bulb by pushing the bulb towards the right until the left side of the bulb is clear of the left socket.

❒To insert the new bulb, push the bulb into the right socket so the bulb fits completely into the left socket.

❒Check that the bulb is seated properly.

❒Re-install the glass cover.

For proper operation and safety,the light fixture must be above the sensor and the sensor head must be rotated so that the controls are on the bottom.

White to White

Junction box ground wire to green ground wire on fixture.

598-1323-01

Page 1 Page 3
Image 2
Page 1 Page 3
Contents Operation FeaturesMode Switching Summary ModelBulb Installation and Re-lamping InstallationWire the Light Control Mount the Light ControlMaximum Range Test and AdjustmentSpecifications Least SensitiveTEN Year Limited Warranty Troubleshooting GuideNo Service Parts Available for this Product Características FuncionamientoModelo RequisitosInstale el control de luz InstalacionConecte el control de luz Instalación y cambio de bombillaAngulo de Prueba Y AjusteEspecificaciones Cobertura MáximaNo hay piezas de servicio disponibles para este producto Guia DE Investigacion DE AveriasServicio Técnico Garantía Limitada a 10 AñosCaractéristiques FonctionnementModèle ExigencesNoir / noir Montage De La Commande D’ÉclairageInstallation et remplacement de ’ampoule Blanc /blancPortée maximale Angle de Essais ET RéglagesFiche Technique Le moins sensibleGarantie Limitée DE 10 ANS Service TechniqueGuide DE Dépannage

5310 specifications

The Heath Zenith 5310 is a prominent choice in the realm of motion-activated outdoor lighting. Engineered for both functionality and durability, this versatile fixture caters to residential needs, providing security and illumination where it's most needed.

One of the main features of the Heath Zenith 5310 is its advanced motion sensor technology. It is equipped with a passive infrared (PIR) sensor that detects movement within a particular range. This sensor can cover an impressive distance of up to 30 feet, allowing it to effectively monitor larger areas. Additionally, the detection angle is approximately 180 degrees, ensuring that no movement goes unnoticed. This is particularly beneficial for homeowners seeking to enhance security around entryways, driveways, and garages.

The light output of the Heath Zenith 5310 is also noteworthy. With a bright LED bulb, it provides adequate illumination while being energy-efficient. The LED technology not only helps to reduce electricity bills but also promotes longevity, as the bulbs have a longer life span compared to traditional incandescent bulbs. This results in minimal maintenance and a lower environmental footprint.

Another significant characteristic of the Heath Zenith 5310 is its adjustable settings. Users can customize the duration for which the light remains on after detecting movement, with options ranging from a few seconds to several minutes. The sensitivity of the motion detector can also be fine-tuned to suit specific environments, allowing for optimal performance regardless of external conditions.

The design of the Heath Zenith 5310 is rooted in practicality and aesthetics. It typically features a sleek and modern appearance that can blend seamlessly with various architectural styles. The durable housing is weather-resistant, ensuring that the fixture can withstand harsh outdoor conditions such as rain, snow, and extreme temperatures, making it a reliable choice for year-round use.

Installation is straightforward, thanks to its user-friendly design. Most homeowners find that they can install the fixture themselves without the need for professional assistance. This adds to the overall appeal of the Heath Zenith 5310, as it combines cutting-edge technology with ease of use, delivering security and convenience in one package.

In summary, the Heath Zenith 5310 stands out as an excellent option for those looking to enhance their outdoor lighting. With its motion detection capability, energy-efficient LED technology, customizable settings, and durable design, it caters to both security and aesthetic needs, making it a smart investment for any homeowner.
Top Page Image Contents