Bard WH183, WH242 Start UP, Important Installer Note, Crankcase Heaters, Service Hints

Page 15

START UP

IMPORTANT INSTALLER NOTE

For improved start up performance, wash the indoor coil with a dish detergent.

CRANKCASE HEATERS

WH241 units are provided with compressor crankcase heat.

These models have an insertion well-type heater located in the lower section of the compressor housing. This is a self-regulating type heater that draws only enough power to maintain the compressor at a safe temperature.

Some form of crankcase heat is essential to prevent liquid refrigerant from migrating to the compressor causing oil pump out on compressor start up and possible valve failure due to compressing a liquid.

The decal in Figure 9 is affixed to all outdoor units detailing start up procedure. This is very important. Please read carefully.

SERVICE HINTS

1.Caution homeowner to maintain clean air filters at all times. Also, not to needlessly close off supply and return air registers. This reduces air flow through the system which shortens equipment service life as well as increasing operating costs.

2.Switching to heating cycle at 75° F or higher outside temperature may cause a nuisance trip of the remote reset high pressure switch. Turn thermostat off, then on, to reset the high pressure switch..

3.The heat pump wall thermostats perform multiple functions. Be sure that all function switches are correctly set for the desired operating mode before trying to diagnose any reported service problems.

4.Check all power fuses or circuit breakers to be sure they are the correct rating.

5.Periodic cleaning of the outdoor coil to permit full and unrestricted airflow circulation is essential.

SEQUENCE OF OPERATION

COOLING – Circuit R-Y makes at thermostat pulling in compressor contactor, starting the compressor and outdoor motor. The G (indoor motor) circuit is automatically completed on any call for cooling operation or can be energized by manual fan switch on subbase for constant air circulation.

HEATING – a 24V solenoid coil on reversing valve controls heating cycle operation. Two thermostat options, one allowing “Auto” changeover from cycle to cycle, and the other constantly energizing solenoid coil during heating season and thus eliminating pressure equalization noise except during defrost, are to be used. On “Auto” option, a circuit is completed from R-W1 and R-Y on each heating “ON” cycle energizing reversing valve solenoid and pulling in compressor contactor starting compressor and outdoor motor. R-G also make starting indoor blower motor. Heat Pump heating cycle now in operation. The second option has no “Auto” changeover position, but instead energizes the reversing valve solenoid constantly whenever the system switch on subbase is placed in “Heat” position, the “B” terminal being constantly energized from R. A thermostat demand for heat completes R-Y circuit pulling in compressor contactor starting compressor and outdoor motor. R-G also make starting indoor blower motor.

FIGURE 9

IMPORTANT

THESE PROCEDURES MUST BE FOLLOWED AT INITIAL START UP AND AT ANY TIME POWER HAS BEEN REMOVED FOR 12 HOURS OR LONGER.

TO PREVENT COMPRESSOR DAMAGE WHICH MAY RESULT FROM THE PRESENCE OF LIQUID REFRIGERANT IN THE COMPRESSOR CRANK- CASE:

1.MAKE CERTAIN THE ROOM THERMOSTAT IS IN THE “OFF” POSITION. (THE COMPRESSOR IS NOT TO OPERATE.)

2.APPLY POWER BY CLOSING THE SYSTEM DISCONNECT SWITCH. THIS ENERGIZES THE COMPRESSOR HEATER WHICH EVAPORATES THE LIQUID REFRIGERANT IN THE CRANK- CASE.

3.ALLOW 4 HOURS OR 60 MINUTES PER POUND OF REFRIGERANT IN THE SYSTEM AS NOTED ON THE UNIT RATING PLATE, WHICHEVER IS GREATER.

4.AFTER PROPERLY ELAPSED TIME THE THERMOSTAT MAY BE SET TO OPERATE THE COMPRESSOR.

5.EXCEPT AS REQUIRED FOR SAFETY WHILE SERVICING — DO NOT OPEN SYSTEM

DISCONNECT SWITCH.

7961-061

Manual 2100-373

Page 13

Page 14 Page 16
Image 15
Page 14 Page 16
Contents WH183 WH242 Installation Instructions Wall Mounted Package Heat PumpContents Getting Other Information and Publications General Wall Mount General InformationHeat Pump Wall Mount Model Nomenclature Shipping DamageUnit Dimensions Electrical Specifications Wire SizeDuct Work Condensate Drain Fresh AIR Damper AssemblyFilters Fresh AIR IntakeInstallation Instructions Wall Mounting InformationMounting the Unit Mounting Instructions Wall Mounting Instructions Common Wall Mounting Installations Unit 24V Terminal Board Wiring Main PowerWiring LOW Voltage Wiring Thermostat Wire SizeCompressor Cutoff Thermostat and Outdoor Thermostats Wall Thermostat and Subbase Combinations Thermostat Indicator LampsHeat Anticipation Compressor Malfunction LightCrankcase Heaters Important Installer NoteService Hints Start UPPressure Service Ports Defrost CycleDefrost Control Board Troubleshooting Solid State Heat Pump Control Troubleshooting ProcedureTroubleshooting Temperature F VS Resistance R of Temperature Sensor Checking Temperature Sensor Outside Unit CircuitIndoor Blower Performance FAN Blade Setting DimensionsRemoval of the FAN Shroud Refrigerant ChargePressure 100 105 110 115 Pressure Table CoolingPressure Table Heating Return Air ModelWH183-A WH242-A WH242-B WH242-C Optional Accessories

WH183, WH242 specifications

The Bard WH242 and WH183 are innovative heating and cooling systems designed to meet the demands of various residential and commercial applications. These units are recognized for their efficiency, reliability, and advanced technologies, making them popular choices among property owners and HVAC professionals.

The Bard WH242 is a high-capacity unit that delivers optimal temperature control, making it ideal for larger spaces. It boasts a robust design and a powerful compressor, which work together to provide consistent heating and cooling throughout the year. The unit features a multi-speed blower, helping to distribute air evenly while also enhancing comfort levels. Energy efficiency is a key highlight, as the WH242 complies with Energy Star standards, which means it consumes less energy while offering high performance.

On the other hand, the Bard WH183 is designed for smaller spaces without compromising on comfort or efficiency. It incorporates a compact design, making it easier to install in tight spaces. Despite its size, the WH183 is equipped with advanced technologies that ensure reliable operation. Like the WH242, this unit also features a multi-speed blower, which aids in maintaining a steady and comfortable indoor climate.

Both models utilize high-quality insulation and advanced refrigerant management systems that minimize energy loss. The systems are also equipped with advanced diagnostics, allowing for easier maintenance and troubleshooting. This means that HVAC technicians can quickly identify potential issues, ensuring that the units remain operational with minimal downtime.

Overall, the Bard WH242 and WH183 represent cutting-edge solutions for temperature management. Their design emphasizes durability, efficiency, and user-friendliness, appealing to a wide range of customers. With their combination of power, compactness, and advanced features, these units are well-suited for diverse applications, including schools, offices, and residential homes. Whether for heating in the winter or cooling in the summer, Bard's commitment to quality and innovation is evident in both the WH242 and WH183 models, making them a smart choice for efficient climate control.
Top Page Image Contents