Pressure Service Ports, Defrost Cycle | Bard WH242, WH183 instruction

PRESSURE SERVICE PORTS

High and low pressure service ports are installed on all units so that the system operating pressures can be observed. Pressure curves can be found later in the manual covering all models on both cooling and heating cycles. It is imperative to match the correct pressure curve to the unit by model number.

DEFROST CYCLE

The defrost cycle is controlled by temperature and time on the solid state heat pump control. See Figure 10.

When the outdoor temperature is in the lower 40° F temperature range or colder, the outdoor coil temperature is 32° F or below. This coil temperature is sensed by the coil sensor mounted near the bottom of the outdoor coil. Once coil temperature reaches 30° F or below, the coil sends a signal to the control logic of the heat pump control and the defrost timer will start.

After 30 minutes at 30° F or below, the heat pump control will place the system in the defrost mode.

During the defrost mode, the refrigerant cycle switches back to the cooling cycle, the outdoor motor stops, electric heaters are energized, and hot gas passing through the outdoor coil melts any accumulated frost. When the temperature rises to approximately 57° F, the coil sensor will send a signal to the heat pump control which will return the system to heating operations automatically.

If some abnormal or temporary condition such as a high wind causes the heat pump to have a prolonged defrost cycle, the heat pump control will restore the system to heating operation automatically after 10 minutes.

There are three settings on the heat pump control – 30 minute, 60 minute, and 90 minute. Models are shipped wired on the 30 minute setting for greatest operating

FIGURE 10

DEFROST CONTROL BOARD

economy. If special circumstances require a change to another time, remove wire connected to terminal 30 and reconnect to desired terminal. Refer to Figure 10. The manufucturer’s recommendation is for 3 minute defrost cycles.

There is a cycle speed up jumper on the control. This can be used to reduce the time between defrost cycle operation without waiting for time to elapse.

Use a small screwdr4iver or other metallic object, or another 1/4 inch QC, to short between the SPEEDUP terminals to accedlerate the HPC timer and initiate defrost.

Be careful not to touch any other terminals with the instrument used to short the SPEEDUP terminals. It may take up to 10 seconds with the SPEEDUP terminals shorted for the speedup to be completed and the defrost cycle to start.

As soon as the defrost cycle kicks in remove the shorting instrument from the SPEEDUP terminals. Otherwise the timing will remain accelerated and run through the 1 minute maximum defrost length sequence in a matter of seconds and will automatically terminate the defrost sequence.

There is an initiate defrost jumper (sen jump) on the control that can be used at any outdoor ambient during the heating cycle to simulate a 0° coil temperature. This can be used to check defrost operation of the unit without waiting for the outdoor ambient to fall into the defrost region.

By placing a jumper across the SEN JMP terminals (a 1/ 4 inch QC terminal works best) the defrost sensor mounted on the outdoor coil is shunted out and will activate the timing circuit. This permits the defrost cycle to be checked out in warmer weather conditions without the outdoor temperature having to fall into the defrost region.

In order to terminate the defrost test the SEN JMP jumper must be removed. If left in place too long the compressor could stop due to the high pressure control opening because of high pressure condition created by operating in the cooling mode with outdoor fan off. Pressure will rise fairly fast as there is likely no actual frost on the outdoor coil in this artificial test condition.

There is also a 5 minute compressor time delay function built into the HPC. This is to protect the compressor from short cycling conditions. In some instances it is helpful to the service technician to override or speed up this timing period, and shorting out the SPEEDUP terminals for a few seconds can do this.

MIS-1174

Manual 2100-373

Page 14

WH183, WH242 specifications

The Bard WH242 and WH183 are innovative heating and cooling systems designed to meet the demands of various residential and commercial applications. These units are recognized for their efficiency, reliability, and advanced technologies, making them popular choices among property owners and HVAC professionals.

The Bard WH242 is a high-capacity unit that delivers optimal temperature control, making it ideal for larger spaces. It boasts a robust design and a powerful compressor, which work together to provide consistent heating and cooling throughout the year. The unit features a multi-speed blower, helping to distribute air evenly while also enhancing comfort levels. Energy efficiency is a key highlight, as the WH242 complies with Energy Star standards, which means it consumes less energy while offering high performance.

On the other hand, the Bard WH183 is designed for smaller spaces without compromising on comfort or efficiency. It incorporates a compact design, making it easier to install in tight spaces. Despite its size, the WH183 is equipped with advanced technologies that ensure reliable operation. Like the WH242, this unit also features a multi-speed blower, which aids in maintaining a steady and comfortable indoor climate.

Both models utilize high-quality insulation and advanced refrigerant management systems that minimize energy loss. The systems are also equipped with advanced diagnostics, allowing for easier maintenance and troubleshooting. This means that HVAC technicians can quickly identify potential issues, ensuring that the units remain operational with minimal downtime.

Overall, the Bard WH242 and WH183 represent cutting-edge solutions for temperature management. Their design emphasizes durability, efficiency, and user-friendliness, appealing to a wide range of customers. With their combination of power, compactness, and advanced features, these units are well-suited for diverse applications, including schools, offices, and residential homes. Whether for heating in the winter or cooling in the summer, Bard's commitment to quality and innovation is evident in both the WH242 and WH183 models, making them a smart choice for efficient climate control.