Cadet RM202, RM208, RM162, RM108, RM151 warranty Installation Instructions, Part One, Step

READ ALL INSTRUCTIONS AND SAFETY INFORMATION

IMPORTANT!

It is extremely important you verify the electrical supply wires are the same voltage as the heater (i.e. 120 volt heater to 120 volt power

supply and 240 volt heater to 240 volt power supply).

If replacing an existing heater, check the labels of the old heater and replace using the same voltage. Hooking a 240 volt heater to a 120 volt power supply will drastically reduce the heater's output. Hooking a 120 volt heater to a 240 volt power supply will destroy the heater. Connecting your heater to an incompatible power supply will void the warranty.

Warranty is void if any material is sprayed on the element or blower.

Installation Instructions

Part One

PLACEMENT: For best results install The Register Plus on an inside wall. Headers and bracing are not

necessary. NOTE: The wall can must be installed in the TOP UP (horizontal) position only. Heater is not approved for ceiling mount.

THERMOSTAT: A thermostat is required. A Cadet Electronic Thermostat is recommended for ultimate control and comfort.

How do I install for new construction?			How do I install in an existing wall?
	Mount Wall Can			Cut Hole In Wall
STEP 1			STEP 1
The RM series REQUIRES A MINIMUM distance			Cut a hole 12 ¾ inches wide by 6 inches high
of 6 inches from adjacent surfaces and 4 ½ inches			next to wall stud. The RM series REQUIRES A
from the floor. However, Cadet RECOMMENDS			MINIMUM distance of 6 inches from adjacent
12 inches from all adjacent surfaces and 12 inches			surfaces and 4 ½ inches from the floor. However,
from the floor (See Figure 5) for longer and cleaner			Cadet RECOMMENDS 12 inches from all adjacent
performance. Heaters must be spaced at least			surfaces and 12 inches from the floor (See
3 feet apart.			Figure 5) for longer and cleaner performance.
Secure the wall can to the studs and/or sill plate			Heaters must be spaced at least 3 feet apart.
with screws through the larger (3/16 inch) holes.
(See Figures 1 and 2).
		FIGURE 1
		Metal legs position wall can
		at minimum floor clearance.

	FIGURE 2
	Bend one leg	FIGURE 5
	90 degrees
	for higher	STEP 2 Route Supply Wires
	placement
		Route supply wire from circuit breaker to wall
	and secure
	to studs.	thermostat, then to wall can. Remove a knockout
		and attach the supply wire with a strain relief
		connector leaving 10 inches wire lead for later
	FIGURE 3	use (See Figure 4). Connect supply ground wire
	Face of wall can must	to grounding pigtail in wall can.
	extend ½ inch or 5/8	STEP 3 Mount Wall Can
	inch from face of stud
	to allow for thickness	FIGURE 6
	of sheetrock. Mount
		Insert wall can, legs
	wall can flush with
		first, into opening
	finished surface.
		and rotate into wall.
STEP 2 Route Supply Wires
Route supply wire from circuit breaker to
thermostat to wall can. Remove a knockout
and attach the supply wire with a strain relief
connector leaving 10 inches wire lead for later
use. Connect supply ground wire to grounding		FIGURE 7
pigtail in wall can (See Figure 4). Proceed to
PART TWO.		Keeping front of
		wall can flush with
SUPPLY	FIGURE 4	finished surface,
WIRE		secure to wall stud
		with screws through
	KNOCK-OUT	larger (3/16 inch) holes.
	(TWIST TO
	REMOVE)	IMPORTANT: Insert two drywall screws into
	STRAIN RELIEF	the small holes opposite the wall stud into the
		drywall to rest against backside of sheetrock
	CONNECTOR	(keeping wall can flush to wall).
GROUNDING
WIRE	GROUNDING	Proceed to PART TWO.
WIRE	PIGTAIL
CONNECTOR