Dyna-Glo RMC-KFA120TDLX, RMC-KFA170TDLX Long Term Storage of Your Heater Fuel Tank Drain

Page 6

NEVER LEAVE THE HEATER

UNATTENDED WHILE BURNING!

8. LONG TERM STORAGE OF YOUR HEATER

FUEL TANK DRAIN

1.Remove Fuel Cap and Cap Fuel Filter(See Figure 10).

2.Drain Fuel Tank through Fuel Cap Opening and wash Fuel Cap Filter with clean fuel.

3.Using a small amount of kerosene,swirl and rinse the inside of the tank.

NEVER LEAVE THE HEATER

UNATTENDED WHILE BURNING!

9.MAINTENANCE

WARNING!! : NEVER SERVICE HEATER WHILE IT IS PLUGGED IN OR WHILE HOT!

USE ORIGINAL EQUIPMENT REPLACEMENT PARTS. Use of third party or other alternate components will void warranty and may cause unsafe operating conditions.

Never mix water with the kerosene as it will cause poor operation of the heater. Pour the kerosene out making sure that you remove it all.

IMPORTANT : Do not store kerosene over summer months for use during next next heating season. Using old fuel could damage heater.

4.Reinstall Fuel Cap Filter and Fuel Cap(See Figure 11).

IMPORTANT : Reinstall Fuel Cap Filter fully into Fuel Cap Opening on tank,

Otherwise it will not install completely.

Figure 10. Remove Fuel Cap and Filter

Figure 11. Reinstall Fuel Cap Filter

5.Store heater in dry well ventilated area. Make sure storage place is free of dust and corrosive fumes.

6.Store the heater in the original box with the original packing material and keep the USER'S MANUAL with the heater.

A.) FUEL TANK

FLUSH EVERY 200 HOURS OF

OPERATION OR AS NEEDED (SEE

STORAGE, PAGE 9)

B.) UPPER SHELL REMOVAL

-Remove Screw that secure Side Cover.

-Push out for arrow direction and extract Side Cover's Bracket from Rectancle Hole and Separate Side Cover(R).

-Side Cover(L) in opposite of Side Cover(R) Separates by same method.

(RMC-KFA120T/170TDLX Models Only.)

-Remove 4 Screws along each side of heater using medium phillips screwdriver. These Screws attach Upper Rear and Lower shells together. (See Figure 12)

(RMC-KFA65TDLX Model Only.)

-Remove Screws along each side of heater using medium phillips screwdriver. These Screws attach Upper and Lower shells together.

C.) AIR OUTPUT,AIR INTAKE AND LINT FILTERS WASH AND DRY WITH SOAP AND WATER OR REPLACE EVERY 500 HOURS OF OPERATION OR ONCE A YEAR.

-Remove Upper Shell.(See Figure 12) -Remove Fan guard.(See Figure 13)

-Remove End Filter Cover Screws using medium phillips screwdriver.

-Remove End Filter Cover.

-Replace Air Output and Lint Filters.

-Wash or Replace Air Intake Filter.

-Reinstall Fan Guard and Upper Shell.

Figure 12. Upper Shell Removal.

Figure 13. Air Output,Intake,and Lint Filters

9

10

Image 6
Contents USER’S Manual Risk of Indoor AIR Pollution Contents of USER’S ManualFeatures Risk of BURNS/FIRE/EXPLOSIONUnpacking and Assembly RMC-KFA/65TDLX RMC-KFA120TDLXAssembly Kerosene 1-KOperation Ventilation Overview of Heaters DesignFueling Your Heater OperationFuel Tank MaintenanceLong Term Storage of Your Heater Fuel Tank Drain Upper Shell RemovalSpark Plug FAN BladesNozzle PhotocellModel Pump Pressure RMC-KFA65TDLX Pump Pressure AdjustmentClean or Replace Twice a Heating Season or AS Need RMC-KFA120TDLXWiring Diagram Specifications ModelDescription Partno AccessoriesExploded Parts Drawing Bracket Side CoverDescription RMC-KFA120TDLX RMC-KFA170TDLXParts List Wheels and Handle RMC-KFA65TDLX Model RMC-KFA120T/170TDLX ModelsKEY Description