Desa CCL3924PTA/NTA, CRL3124PA/NA Cleaning Maintenance, Service Hints, Technical Service, Logs

Page 24

CLEANING AND

MAINTENANCE

Continued

2.Inspect burner, pilot and primary air inlet holes on injector holder for dust and dirt (see Figure 36).

3.Blow air through the ports/slots and holes in the burner.

4.Check the injector holder located at the end of the burner tube again. Remove any large particles of dust, dirt, lint or pet hair with a soft cloth or vacuum cleaner nozzle.

5.Blow air into the primary air holes on the injector holder.

6.In case any large clumps of dust have now been pushed into the burner repeat steps 3 and 4.

Clean the pilot assembly also. A yellow tip on the pilot flame indicates dust and dirt in the pilot as- sembly. There is a small pilot air inlet hole about two inches from where the pilot flame comes out of the pilot assembly (see Figure 37). With the unit off, lightly blow air through the air inlet hole. You may blow through a drinking straw if compressed air is not available.

Burner Tube

Injector Holder

Primary Air

Inlet Holes

Figure 36 - Injector Holder On Outlet

Burner Tube

Ports/Slots

Burner Tube

Pilot Assembly

Pilot Air

Inlet Hole

Figure 37 - Pilot Inlet Air Hole

LOGS

•If you remove logs for cleaning, refer to Install- ing Logs, page 16, to properly replace logs.

•Replace log(s) if broken or chipped (dime-sized or larger).

Main Burner

Periodically inspect all burner flame holes with the heater running. All slotted burner flame holes should be open with yellow flame present. All round burner flame holes should be open with a small blue flame present. Some burner flame holes may become blocked by debris or rust, with no flame present. If so, turn off heater and let cool. Remove blockage. Blocked burner flame holes will create soot.

Service Hints

When Gas Pressure Is Too Low

• pilot will not stay lit

• burners will have delayed ignition

• heater will not produce specified heat

• for propane/LP units, propane/LP gas supply may be low

You may feel your gas pressure is too low. If so, contact your local propane/LP or natural gas supplier.

Technical Service

You may have further questions about installation, operation or troubleshooting. If so, contact DESA Heating Products’ Technical Service Department at 1-866-672-6040. When calling please have your model and serial numbers of your heater ready.

You can also visit DESA Heating Products’techni- cal service web site at www.desatech.com.

24

www.desatech.com

113097-01E

Page 23 Page 25
Image 24
Page 23 Page 25
Contents What to do if YOU Smell GAS Table of Contents Safety Information Safety Information Local CodesProduct Features Product IdentificationUnpacking Air for Combustion VentilationAIR for Combustion Ventilation Providing Adequate VentilationDetermining FRESH-AIR Flow For Heater LocationVentilation AIR Ventilation Air From Inside BuildingVentilation Air From Outdoors Installation Check GAS TypeInstallation Installation and Clearances Vent-Free Operation OnlyAccessories, Mantel ClearancesInstalling Damper Clamp Accessory for Vented Operation Floor ClearancesInstalling Heater Base Assembly Installation Items NeededChimney Minimum Permanent Area of Various Standard Round FluesConnecting to GAS Supply Attaching Base Assembly to Fireplace Floor Dual Burner ModelChecking GAS Connections Propane/LPNatural Pressure Testing Heater Gas Connections Test Pressures Equal To or Less Than Psig 3.5 kPaInstalling Logs CCL3930PTB/NTBInstalling Crossover Log #4 CCL3930PTB/NTB Shown Installing Back Log For Your Safety Read Before LIGHTING  Operating HeaterManually-Controlled Models  LIGHTING Instructions MANUAL Lighting Procedure Operating Heater VARIABLE Control Operation  TO Turn OFF GAS To ApplianceFor Your Safety Read Before Lighting Thermostat-Controlled ModelsLighting Instructions Manual Lighting Procedure To Turn OFF GAS To ApplianceThermostat Control Operation Cleaning Maintenance Inspecting BurnersPilot Flame Pattern Burner Primary AIR HolesCleaning Maintenance Service HintsTechnical Service When Gas Pressure Is Too LowTroubleshooting Observed Problem Possible Cause RemedyTroubleshooting Maintenance,Gas leak. See Warning Statement aboveOptional Positioning Thermostat Sensing Bulb For Masonry and Factory- built Metal FireplaceSpecifications Optional Positioning Thermostat Sensing BulbDual Burner Biltmore split OAK Models Single Burner Seasonal OAK ModelsIllustrated Parts Breakdown Parts List Variable Manually-Controlled biltmore split oak ModelsIllustrated Parts Breakdown Parts List Thermostatically-Controlled Biltmore Split Oak ModelsPeg positions vary according to model Left Top Crossover Log #5 3A 3B Variable Manually-Controlled Seasonal Oak Models Replacement Parts AccessoriesEquipment Shutoff Valve GA5010 Fireplace HoodParts Central Warranty Information Keep this WarrantyLimited Warranty Comfort Glow VENT-FREE GAS LOG Heaters

CCL3018PTA/NTA, RL2718PA/NA, CCL3924PA/NA, CCL3924PTA/NTA, CCL3930PTB/NTB specifications

Desa CCL3924PTA/NTA, CCL3018PTA/NTA, CCL3930PTB/NTB, CCL3924PA/NA, and CCL3018PA/NA are a lineup of advanced cooling units designed to meet diverse needs in thermal management for residential, commercial, and industrial applications. Each model brings together a blend of innovative technology and user-friendly features that ensure efficient performance and reliability.

The CCL3924PTA/NTA model is designed for high-performance cooling, offering a blend of efficiency and sustainable operation. Its inverter technology allows for variable speed control, leading to lower energy consumption and quieter operation. This model is particularly suited for larger spaces, providing consistent cooling throughout the environment while maintaining energy efficiency.

CCL3018PTA/NTA is a compact unit that excels in environments with space constraints. Despite its smaller size, it delivers robust cooling performance, making it ideal for residential settings or small office spaces. Its lightweight design and easy installation capabilities reduce downtime and allow for swift setup, while its smart thermostat controls enable precise temperature management.

For environments that require intensive cooling, the CCL3930PTB/NTB model stands out with its powerful compressor and larger cooling capacity. This unit is engineered for industrial applications, featuring heavy-duty components that ensure long operational life even in demanding conditions. Its multi-zone capability allows users to cool several areas simultaneously, providing tailored solutions for complex layouts.

The CCL3924PA/NA variant focuses on energy efficiency without compromising on cooling power. This model is equipped with advanced thermal insulation technology, minimizing heat exchange and enhancing its performance during peak usage. Users benefit from significant energy savings, making it an environmentally friendly choice for those concerned about carbon footprints.

Lastly, the CCL3018PA/NA brings versatility with its dual-function capability. This model not only serves as a cooling unit but can also function as a heater, making it a year-round solution for climate control. Its efficient heat pump technology makes it an ideal choice for locations with varying seasonal temperatures, ensuring comfort throughout the year.

In conclusion, the Desa lineup of cooling solutions combines cutting-edge technology, energy efficiency, and user-friendly features, catering to a wide array of applications and user needs. Each model has been engineered with a focus on durability and reliability, making them a smart investment for anyone looking to enhance their indoor climate control systems.
Top Page Image Contents