Desa BTU/HR owner manual Operation with Portable Generator, Storing TRANSPORTING, or Shipping

Page 6

OPERATION

Continued

TO RESTART HEATER

Wthout ON/OFF Switch

1.Unplug extension cord from outlet and wait 10 seconds. (Wait two minutes if heater has been running.)

2.Repeat steps under To Start Heater.

With ON/OFF Switch

1.Push ON/OFF switch to OFF (O) position and wait 10 seconds (2 minutes if heater has been running).

2.Repeat steps under To Start Heater, page 5.

ON/OFF

Switch with

Light

Figure 7 - ON/OFF Switch, 50/55/60/70 Models

ON/OFF

Switch with

Light

Figure 8 - ON/OFF Switch, 110/115/155/

165/200 Models

OPERATION WITH

PORTABLE GENERATOR

WARNING: Before operating heater or any appliance from a portable generator, verify that generatorhasbeen properlycon- nected to earth ground. Improper grounding or failure to ground generator can result in electro- cution if a ground fault occurs. Refertoowner’smanualsupplied by generator manufacturer for proper grounding procedures.

The operating voltage range of the heater is 108 to 132 Volts (120 Volts +/- 10%). Prior to plug- ging heater into generator the output voltage should be verified (if generator is equipped with the automatic idle feature, the output voltage should be measured with the generator running at full speed). If the voltage does not measure in this range the heater should not be plugged into the generator.

Refer to Operation, page 5, for starting, stopping, and resetting heater procedures.

Alternator

Ground Lug

Copper or

Brass

Grounding

Point

Ground Wire (#10

AWG - Stranded-

Copper)

Figure 9 - Typical Generator Grounding Method (Generator construction may vary from that shown)

STORING,

TRANSPORTING, OR

SHIPPING

Note: If shipping, transport companies require fuel tanks to be empty.

1.Drain fuel tank. Note: Some models have drain plug on underside of fuel tank. If so, remove drain plug to drain all fuel. If heater does not have drain plug, drain fuel through fuel cap opening. Be sure all fuel is removed.

2.Replace drain plug if provided.

3.If any debris is noted in old fuel, add 1 or 2 quarts of clean kerosene to tank, stir, and drain again. This will prevent excess debris from clogging filters during future use.

4.Replace fuel cap or drain plug. Properly dis- pose of old and dirty fuel. Check with local automotive service stations that recycle oil.

5.If storing, store heater in dry place. Make sure storage place is free of dust and corrosive fumes.

IMPORTANT: Do not store kerosene over sum- mer months for use during next heating season. Using old fuel could damage heater.

6

www.desatech.com

113282-01C

Image 6
Contents Table of Contents Safety Information Unpacking Product IdentificationNever attach heater to external fuel tank Fuels VentilationTheory of Operation For 110/115/155/165/200 Models only AssemblyOperation To Start HeaterStoring TRANSPORTING, or Shipping Wthout ON/OFF SwitchOperation with Portable Generator To Restart HeaterFault Condition Possible Cause Remedy Preventative Maintenance ScheduleTroubleshooting How Often How ToObstruction in nozzle Ment,Dirty fuel filter Water in fuel tankAIR OUTPUT, AIR Intake and Lint Filters Service ProceduresUpper Shell Removal FANPump Pressure Adjustment Fuel FilterReplace filter end cover Carefully remove replacement ignitor from packing IgnitorReplace combustion chamber Nozzle Assembly Place plastic hex-body into vise and lightly tightenFor 40/50/55/60/70/110/115/155/165 Models Only Fuel and AIR Line Replacement and Proper Routing For 200 Model OnlyProcedure if Rotor is Binding Pump RotorModel Size SpecificationsIgnition Control Assembly 110/115 155 165 200Wiring Diagrams Ignition Control AssemblyWiring Diagrams R40, REM40, PK40, UK40, TK40, N40 Illustrated Parts BreakdownStandard Model Thermostat ModelsParts List ModelsStandard Model 50/55/60/70 Models NTC-4CStandard Models 110/115/155/165 Models WLE-2R200B, PK200, UK200, TK200 RM200BT, B200BT, PK200T, UK200T, TK200T, REM200BT, R200BTSee Burner Head Assembly for 110/115/155/165 Models NOZZLE/BURNER Head Assembly for 200 ModelsMotor and Pump Assembly for 40/50/55/60/70 Models FHPF3-5CMotor and Pump Assembly for 110/115/155/165 Models FHPF3-5CMotor and Pump Assembly for 200 Models Parts Under Warranty Replacement PartsWheels and Handle Parts List Parts not Under WarrantyTechnical Service AccessoriesWarranty and Repair Service Limited Warranty

BTU/HR specifications

Desa BTU/HR is an innovative energy solution that emphasizes efficiency and sustainability in thermal energy generation. Designed with the modern consumer in mind, the Desa BTU/HR platform integrates advanced technologies to optimize heating systems for both residential and commercial applications.

At its core, Desa BTU/HR operates on the principle of maximizing thermal energy while minimizing waste. This is achieved through state-of-the-art heat exchangers and combustion technologies that ensure a higher yield of usable heat per unit of fuel consumed. By utilizing a variety of inputs, including biomass, natural gas, and renewable sources, Desa BTU/HR caters to a range of energy requirements, making it versatile for diverse environments.

One distinguishing feature of the Desa BTU/HR system is its intelligent control mechanism. Equipped with smart sensors and an integrated software platform, the system continuously monitors performance and adjusts operations in real-time. This proactive management contributes to enhanced efficiency, reducing energy consumption and operational costs. Furthermore, the system allows for remote access and monitoring, enabling users to make informed decisions about their energy usage without being on-site.

Another key characteristic of the Desa BTU/HR is its modular design. This means that the system can be scaled to meet changing energy requirements without major overhauls or replacements. Businesses can start with a smaller unit and expand as needed, which is not only cost-effective but also environmentally responsible.

Desa BTU/HR prioritizes sustainability in its operations. By integrating renewable energy sources and reducing greenhouse gas emissions, the platform adheres to international standards for environmentally friendly technologies. This focus on eco-friendly practices aligns with the growing global demand for sustainable energy solutions.

In conclusion, Desa BTU/HR sets a new standard in thermal energy generation through its efficient, intelligent, and sustainable design. With features that promote optimal energy use and a commitment to reducing environmental impact, the system serves as a robust solution for heat generation in today's energy-hungry world. As the landscape of energy production continues to evolve, Desa BTU/HR stands out as a forward-thinking choice for future energy needs.