Desa REM10PT Connecting to Portable Cylinder GAS Supply, Installing Bottom Mounting Screw

Page 6

6

INSTALLATION

Installing Heater To Wall (Cont.) Connecting to Portable Cylinder Gas Supply

INSTALLATION

Continued

Installing Bottom Mounting Screw

1.Locate bottom mounting hole. This hole is near bottom on back panel of heater (see Figure 9).

2.Mark screw location on wall.

3.Remove heater from wall.

4.If installing bottom mounting screw into hollow or solid wall, install wall anchor. Follow steps 1 through 5 under Attaching To Wall Anchor Method, page 5. If installing bottom mounting screw into wall stud, drill hole at marked location using 9/64" drill bit.

5.Replace heater on wall.

6.Insert bottom anchor screw through back panel into bottom anchor or drilled hole (see Figure 9).

7.Tighten screw until heater is firmly secured to wall. Do not over tighten.

Note: Do not replace front panel at this time. Replace front panel after making gas connections and checking for leaks (see pages 9 and 10).

Figure 9 - Installing Bottom Mounting Screw

2.Connect fuel gas fitting on hose/regulator assembly to pro- pane/LP tank(s). Turn fuel gas fitting counterclockwise into threads on tank. Tighten firmly using a wrench. IMPORTANT: Position regulator so that hose leaving the regulator is in a horizontal position (see Figure 10). This places the regulator vent in the proper position to protect it from the weather.

3.Connect hose to heater inlet. Tighten firmly using a wrench. You must use the regulator supplied with heater.

4.Open propane/LP supply valve on propane/LP tank(s) slowly. Note: If not opened slowly, excess-flow check valve on pro- pane/LP tank may stop gas flow. If this happens, close pro- pane/LP supply valve and open again slowly.

5.Check all connections for leaks. Apply a noncorrosive leak detection fluid to gas joints. Bubbles forming show a leak that must be corrected.

6.Close propane/LP supply valve.

Regulator

Propane/LP

Supply

Valve

 

Fuel Gas

 

Propane/LP

Fitting

Hose To

Tank

 

Heater

Figure 10 - Regulator Position

 

 

CONNECTING TO PORTABLE CYLINDER GAS SUPPLY

WARNING: Review and understand the warnings in the Safety Information section, page 2. They are needed to safely operate this heater. Follow all local codes when using this heater.

WARNING: Test all gas piping and connections for leaks after installation or servicing. Never use an open flame to check for a leak. Apply a noncorrosive leak detection fluid to all joints. Bubbles forming show a leak. Correct all leaks at once.

IMPORTANT: You must use a propane/LP gas supply cylinder that is compatible with the connection device provided with the hose and regulator.

1.Provide propane/LP supply system (see Propane/LP Supply, page 4).

Pressure

Regulator

Heater

Cabinet

Hose Fitting

Elbow

Hose To

Regulator

Figure 11 - Gas Connection

For..com

110373-01A

Page 5 Page 7
Image 6
Page 5 Page 7
Contents OWNER’S Operation Installation Manual REM10PTWhat to do if YOU Smell GAS Table of Contents Safety InformationProduct Identification UnpackingLocal Codes Product FeaturesInstallation PROPANE/LP SupplyInstalling Heater to Wall Thermostat Sensing BulbConnecting to Portable Cylinder GAS Supply Installing Bottom Mounting ScrewConnecting to Permanent GAS Supply Installation ItemsPressure Testing Gas Supply Piping System Permanent GAS SupplyOperating Heater For Your Safety Read Before LightingPressure Testing Heater Gas Connections Checking GAS Connections for Permanent GAS SupplyThermostat Control Operation Manual Lighting ProcedureTo Turn OFF GAS To Appliance Shutting Off HeaterPilot Flame Pattern Inspecting BurnerStorage Burner Flame PatternODS/PILOT and Burner Cleaning MaintenanceCleaning Burner Pilot AIR Inlet CabinetTroubleshooting Observed Problem Possible Cause RemedyMaintenance, Gas leak. See Warning statement at Illustrated Parts Breakdown REM10PT PilotParts List REM10PTService Hints SpecificationsTechnical Service Service Publications AccessoriesOwners Registration Form Postage Required 110373-01A Warranty Information

REM10PT specifications

Desa REM10PT, an innovative solution for modern farming, embodies the convergence of advanced technology and sustainable agricultural practices. Recognized for its efficiency and effectiveness, REM10PT serves as a pivotal platform designed to enhance productivity while minimizing environmental impact.

One of the standout features of the Desa REM10PT is its advanced monitoring system. This system utilizes IoT (Internet of Things) technology to provide real-time data on soil conditions, weather patterns, and crop health. By carefully tracking these metrics, farmers can make informed decisions that lead to optimized resource utilization. This capability not only boosts yield but also conserves water and fertilizers, which is crucial in regions facing water scarcity.

Another key characteristic of the Desa REM10PT is its integration of precision agriculture techniques. With GPS-enabled machinery, farmers can apply inputs precisely where needed, reducing waste and increasing efficiency. This technology aligns with the best practices of modern agriculture, ensuring that every inch of land is utilized effectively.

The design of Desa REM10PT emphasizes sustainability. Constructed using eco-friendly materials, it aims to reduce the carbon footprint associated with traditional farming equipment. Furthermore, it promotes practices that enhance soil health, such as reduced tillage and cover cropping, enabling a regenerative approach to farming.

In addition to these features, Desa REM10PT boasts user-friendly software that simplifies data analysis. Farmers can access an intuitive dashboard that aggregates data from various sources, helping them to visualize trends and make swift decisions. This platform also allows for remote monitoring, empowering farmers to manage their operations from anywhere at any time.

Finally, a key component of Desa REM10PT is its emphasis on community and education. The platform is not just a tool; it is a portal for sharing knowledge and best practices among farmers. Through workshops and online resources, it fosters a collaborative environment where users can learn from each other, enhancing the overall agricultural ecosystem.

In summary, Desa REM10PT encapsulates the future of agriculture with its holistic approach, merging advanced technology, sustainability, and community engagement. By adopting such innovative solutions, the agricultural sector moves toward more productive and environmentally responsible practices, ensuring a bountiful future for generations to come.
Top Page Image Contents