Quadra-Fire 3100 owner manual Maintenance

Page 23

MAINTENANCE

CREOSOTE

1.Formation and need for removal: When wood is burned slowly, it produces tar and other organic vapors which combine with expelled moisture to form creosote. The creosote vapors condense in the relatively cool chimney flue of a newly-started or a slow-burning fire. As a result, creosote residue accumulates on the flue lining. When ignited, this creosote creates an extremely hot fire which may damage the chimney or even destroy the house. The chimney connector and chimney should be inspected at least twice monthly during the heating season to determine if a creosote buildup has occurred. If creosote has accumulated, it should be removed to reduce the risk of a chimney fire.

2.Inspection: Inspect the system at the stove connection and at the chimney top. Cooler surfaces tend to build creosote deposits quicker, so it is important to check the chimney from the top as well as from the bottom.

3.Removal: The creosote should be removed with a brush specifically designed for the type of chimney in use. A chimney sweep can perform this service. It is also recommended that before each heating season the entire system be professionally inspected, and cleaned and repaired if necessary.

CARE AND CLEANING OF GLASS

NOTE: Remove all labels from glass before lighting the first fire in your stove.

Quadra-Fire stoves are equipped with ceramic super heat-resistant glass, which can only be broken by impact or misuse. Do not slam stove door or impact the glass. When closing door, make sure that logs do not protrude against the glass. Clean glass with a nonabrasive glass cleaner, such as Windex. Abrasive cleaners may scratch and cause glass to crack. Inspect glass regularly. If you find a crack or break, immediately put the fire out and return the door to your dealer for replacement of glass before further use. Leaving the primary air control open during the entire burn will cause overfiring. Overfiring the appliance may cause crazing, a white non-removable film on inside of glass. Overfiring voids warranty. NOTE: Replace with ceramic glass only.

CARE AND CLEANING OF PLATED SURFACES

Clean 24 karat gold-plated surfaces with vinegar or a glass cleaner before lighting your first fire.

WARNING: When the appliance is equipped with a 24 karat gold-plated door, you must clean all the fingerprints and oils from the gold surface before firing the appliance for the first time. Use a glass cleaner or vinegar and towel to remove the oils. If not cleaned properly before lighting your first fire, the oils can cause permanent markings on the gold plating. After the gold plating is cured, the oils will not affect the finish and little maintenance is required: just wipe clean as needed.

CAUTION: DO NOT USE POLISHES WITH ABRASIVE AGENTS. THEY WILL SCRATCH THE PLATING.

CHIMNEY CLEANING

Disconnect flue pipe from stove before cleaning chimney. Otherwise residue can pile up on top of the baffle, and the stove will not work properly.

ASH REMOVAL

Remove cold ashes (NEVER HOT) from the stove by shoveling them into a metal container with a tight-fitting lid. Spraying cold ashes with water before shoveling them out of the stove will help eliminate ash flying around the firebox and into the room. Always treat ashes as if they contain hot coals, and store the container on a noncombustible floor away from combustible material pending final disposal. If unit is equipped with an ash removal system, see page 19 for operating instructions.

FIREBRICK

The firebox of your Quadra-Fire stove is lined with high quality firebrick, which has exceptional insulating properties. There is no need for use a grate; simply build a fire on the firebox floor of your stove.

OVERFIRING

Do not overfire. Using flammable liquids or too much wood, burning trash in the stove, or allowing too much air into the stove, may result in overfiring. If the chimney connector or stove glows red or even worse, white, the stove is overfired. This condition may ignite creosote in the chimney, which can be dangerous, possibly causing a house fire. If you overfire, immediately close the air controls and door, if open, to reduce the air supply to the fire.

Page 23

Image 23
Contents NorthAmerica’sBest Important Safety NotesTable of Contents Safety Label found on back of stove LEG Model DimensionsPedestal Model Step TOP LEG Model Step TOP Pedestal ModelClearances to Combustibles UL and ULC Chimney Systems Safety ListingInstallation Materials Needed for Your Safety Venting SystemConnection to a Masonry Chimney Chimney ConnectorChimney HEIGHT/DRAFT Page Page Page Page Page Connection to a Metal Prefabricated Chimney Mobile Home Installation Pedestal Models Outside AIR KIT InstallationLEG Models PEDESTAL/LEG KIT Installation LEG Model ASH Removal System InstallationPedestal Model ASH Removal System Operating and Cleaning Operating Instructions Important Please Read Before Using Stove Burning ProcessBurning Guidelines Blower Operating InstructionsOperating Tips Wood Selection and Storage Building a FireMaintenance Glass Replacement Door Handle AssemblyBaffle Removal and Installation Brick Pattern Baffle Removal and InstallationSteps for Adjusting the Blower Speed Control Installation of Optional BlowerBlower Switch Adjustments TOP Heat Shield Installation Accessories Accessories and Service PartsPage Page Lifetime warranty