Quadra-Fire 3100 Operating Instructions, Important Please Read Before Using Stove Burning Process

Page 20

OPERATING INSTRUCTIONS

IMPORTANT - PLEASE READ BEFORE USING STOVE

BURNING PROCESS

In recent years there has been an increasing concern about air quality. Much of the blame for poor air quality has been placed on the burning of wood for home heating. In order to improve the situation, we at Quadra-Fire have developed cleaner-burning wood stoves that surpass the requirements for emissions established by our governing agencies. These wood stoves, like any other appliances, must be properly operated in order to insure that they perform the way they are designed to perform. Improper operation can turn most any wood stove into a smoldering environmental hazard.

It helps to know a little about the actual process of burning in order to understand what goes on inside a stove. The first stage of burning we will call the kindling stage. In this stage, the wood is heated to a temperature high enough to evapo- rate the moisture which is present in all wood. The wood will reach the boiling point of water (212°F) and will not get any hotter until the water is evaporated. This process takes heat from the coals and tends to cool the stove. Fire requires three things to burn: fuel, air and heat. So, if heat is robbed from the stove during the drying stage, the new load of wood has reduced the chances for a good clean burn. For this reason, it is always best to burn dry, seasoned firewood. When the wood isn’t dry, you must open the air controls and burn the stove at a high burn setting for a longer time to start it burning. The control on the right side of the stove is called the primary control; it is used mainly during the kindling stage of burning, or when burning the stove at a high burn setting. It should be closed (pulled outward) for lower burns.

The next stage of burning, the secondary stage, is the period when the wood gives off flammable gases which burn above the fuel with bright flames. During this stage of burning it is very important that the flames be maintained and not allowed to go out. This will insure the cleanest possible fire. If you are adjusting your stove for a low burn rate, you should close down the air to the point where you can still maintain some flame. If the flames tend to go out, the stove is set too low for your burning conditions. The air control in the center of the stove, beneath the ashcatcher, is the one used to adjust the stove for lower burn rates. This is called the secondary control. Pulling either control towards you closes it, pushing it in opens it.

The final stage of burning is the charcoal stage. This occurs when the flammable gases have been mostly burned and only charcoal remains. This is a naturally clean portion of the burn. The coals burn with hot blue flames. It is very important to reload your stove while enough lively hot coals remain in order to provide the amount of heat needed to dry and rekindle the next load of wood. It is best to open the air controls for a short while before reloading. This livens up the coalbed. Open door slowly so that ash or smoke does not exit stove through opening. You should also break up any large chunks and distribute the coals so that the new wood is laid on hot coals.

Air quality is important to all of us, and if we choose to use wood to heat our homes we should do so responsibly. To do this we need to learn to burn our stoves in the cleanest way possible. Doing this will allow us to continue using our wood stoves for many years to come.

PRIMARY AIR SYSTEM

The primary combustion air enters at the rear of the firebox through the primary air tubes. This air supply is controlled by the primary control. For maximum burn rates (more heat) push control in, for minimum burn rates (less heat) pull control out.

SECONDARY AIR SYSTEM

The secondary air enters at the upper front of the firebox, near the top of the glass door. This preheated air supplies the necessary fresh oxygen to mix with the unburned gases, helping to create secondary, tertiary and quaternary combustions. This air is regulated by the secondary control. For more secondary air push control in, for less secondary air pull control out.

Primary control

Secondary control

Page 20

Image 20
Contents Important Safety Notes NorthAmerica’sBestTable of Contents Safety Label found on back of stove LEG Model DimensionsPedestal Model Step TOP Pedestal Model Step TOP LEG ModelClearances to Combustibles UL and ULC Safety Listing Installation Materials Needed for Your SafetyVenting System Chimney SystemsConnection to a Masonry Chimney Chimney ConnectorChimney HEIGHT/DRAFT Page Page Page Page Page Connection to a Metal Prefabricated Chimney Mobile Home Installation Pedestal Models Outside AIR KIT InstallationLEG Models PEDESTAL/LEG KIT Installation LEG Model ASH Removal System InstallationPedestal Model ASH Removal System Operating and Cleaning Important Please Read Before Using Stove Burning Process Operating InstructionsBurning Guidelines Blower Operating InstructionsOperating Tips Building a Fire Wood Selection and StorageMaintenance Door Handle Assembly Glass ReplacementBaffle Removal and Installation Baffle Removal and Installation Brick PatternSteps for Adjusting the Blower Speed Control Installation of Optional BlowerBlower Switch Adjustments TOP Heat Shield Installation Accessories and Service Parts AccessoriesPage Page Lifetime warranty