Quadra-Fire QV36DC-A owner manual Vent Termination

Page 21

For Vertical Runs - One ceiling firestop is REQUIRED at

If the area above the ceiling IS an attic, position and secure

the hole in each ceiling through which the vent passes.

the firestop on top of the previously framed hole.

To install firestops for vertical runs that pass through ceilings:

•Position a plumb bob directly over the center of the verti- cal vent component.

•Mark the ceiling to establish the centerpoint of the vent.

•Drill a hole or drive a nail through this centerpoint.

•Check the floor above for any obstructions, such as wir- ing or plumbing runs.

•Reposition the fireplace and vent system, if necessary, to accommodate the ceiling joists and/or obstructions.

•Cut an 10-inch X 10-inch (254mm X 254mm) hole through the ceiling, using the centerpoint previously marked.

•Frame the hole with framing lumber the same size as the ceiling joists.

10" (254mm)

 

10" (254mm)

 

 

 

 

CHIMNEY

 

 

HOLE

 

NEW

EXISTING CEILING

 

JOISTS

 

FRAMING

CEILING

MEMBERS

 

 

 

Figure 25. 10” x 10” Hole & New Framing Members

If the area above the ceiling is NOT an attic, position and secure the ceiling firestop on the ceiling side of the previously cut and framed hole.

NOTE: There must be NO INSULATION or other combustibles inside the framed firestop opening.

NOTE: Keep insulation away from the vent pipe at least

1 inch (25mm).

 

NAILS (4 REQUIRED)

 

RAFTER

CEILING

 

 

CEILING FIRESTOP

Figure 27.

Attic Firestop

C. Vent Termination

Refer to Cinch Pipe and Termination Cap installation in- structions.

Horizontal Termination

•The termination kit should pass through the wall firestops from the exterior of the building and interlock the flue sections.

•Adjust the termination cap to its final exterior position on the building and interlock the flue sections.

!WARNING: THE TERMINATION CAP MUST BE PO- SITIONED SO THAT THE ARROW IS POINTING UP.

!WARNING: VENTING TERMINALS SHALL NOT BE RECESSED INTO A WALL

OR SIDING. VENT TERMINATION CLEARANCES MUST BE FOLLOWED TO AVOID FIRE DANGER. SEE VENT TERMINATION MINIMUM CLEARANCES DIAGRAM ON FOLLOWING PAGE.

 

JOIST

 

 

CEILING

 

 

 

NAILS (4 REQUIRED)

 

 

 

CEILING FIRESTOP

Figure 28.

(184mm)

 

 

 

7 1/4”

Figure 26.

Ceiling Firestop (Ceiling Side)

Trapezoid Termination Cap

 

24

Quadra-Fire • QV36DC-A • 2161-900 Rev. C • 6/09

 

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Do Discardnot QV36DC-ASafety and Warning Information Table of Contents Appliance Certification Installation Codes High Altitude InstallationsElectrical Codes C22.1Requirements for the Commonwealth of Massachusetts Installation of Carbon Monoxide DetectorsPre-installation Preparation Introducing Quadra-Fire Gas FireplacesANY Such Action MAY Possibly Cause a Fire Hazard Diagram of the QV36DC-A Constructing the Fireplace Chase Fireplace Dimensions, LocationsLocating the Fireplace Clearance Requirements27 7/8 Framing the FireplaceDVP90ST Identifying Vent Components Installing the Vent SystemVent System Approvals Tems or Components MAY be UsedVertical Venting Flue Restrictor Instructions40’ MAX .4 M Straight Up Vertical VentingDegree Elbows Venting with One 90 Elbow Venting with ONE 1 90 ElbowVenting with TWO Elbows Venting with three 90 elbows Venting with Three 3 90 Elbows+ H1 Shield Above the First 900 Elbow in the Venting System Install Support Brackets To Install the Heat Shield12 Hole and Vent Pipe Vent Termination Alcove Applications Minimum Height from Roof to Lowest Discharge Opening Gas Control System Positioning, Leveling, and Securing the FireplaceStanding Pilot Ignition System Standing PilotGas Pressure Requirements Gas Supply LineStep Wiring the Fireplace Optional Accessories Appliance RequirementsWall Switch Hearth Extensions FinishingInstalling Trim, Refractory, Logs Ember Material Installing the TrimRefractory Kit Placement BRICK-292 Lighting the Appliance Before Lighting the FireplaceDo not Connect 110 VAC to the Control Valve For Your Safety Read Before Lighting InstructionsAfter the Installation Fireplace MaintenanceClimate Control Standing Pilot Ignition System Symptom Possible Causes Corrective ActionSymptom Possible Cause Corrective Action TroubleshootingLimited Lifetime Warranty ÎLimited Lifetime Warranty Do not Discard this Manual Contact Information

QV36DC-A specifications

The Quadra-Fire QV36DC-A is a remarkable addition to the world of home heating, exemplifying innovation and efficiency in gas-burning fireplace inserts. Designed for those who seek both aesthetics and functionality in their living spaces, this model offers an impressive blend of features and technologies that enhance not only warmth but also the overall ambiance of any room.

One of the standout characteristics of the QV36DC-A is its direct vent design. This technology allows for a safe and efficient venting system that draws outside air for combustion, ensuring that indoor air quality is maintained. This feature eliminates the need for a traditional chimney, making it an ideal choice for modern homes or those with limited space. The direct vent capability also contributes to a higher efficiency rating, making it more cost-effective and environmentally friendly.

Another key feature of this model is its large viewing area, which is framed by a sleek and stylish surround. The expansive glass front provides a stunning visual display of the flames, creating a warm and inviting atmosphere. The QV36DC-A also comes with a range of decorative options, including various finish choices and customizable log sets, allowing homeowners to tailor the look of their fireplace to suit their personal style.

The QV36DC-A is equipped with advanced heating technologies, including a powerful heating capacity of up to 30,000 BTUs. This ensures that it can effectively heat larger spaces while maintaining a comfortable environment. The unit features adjustable fan speeds and a variable flame control system, allowing users to manipulate the level of heat and ambiance according to their preferences.

Additionally, the Quadra-Fire QV36DC-A is designed for ease of use and maintenance. The included remote control makes it convenient to adjust settings from a distance, while the self-cleaning glass door reduces the frequency of maintenance chores. The durable construction and high-quality materials ensure longevity, making it a wise investment for homeowners.

With its blend of functionality, efficiency, and beauty, the Quadra-Fire QV36DC-A stands as a premier choice for anyone looking to enhance their living space with the warmth and comfort of a gas fireplace insert. Its thoughtful design and advanced features make it not just a source of heat, but a centerpiece that elevates the overall ambiance of any home.
Top Page Image Contents