Blower #1 Small Convection Blower, Feed System

13. BLOWER #1 (SMALL CONVECTION BLOWER)

This blower is located on the right side of the insert. When the insert is pulled out onto the hearth, the blower is accessible through a removable access panel. This blower comes on automatically when snap disc #1 heats up. The blower’s function is to deliver heat from the insert into the room.

14.BLOWER #2 (NEGATIVE DRAFT BLOWER) This blower creates a negative pressure (vacuum) in the firebox. It extracts all of the exhaust out of the firebox and sends it into the venting system. The blower is located on the left side of the insert. When the insert is pulled out onto the hearth, the blower is accessible through a removable access panel.

15.BLOWER #3 (LARGE CONVECTION BLOWER) This blower is located on the left side of the insert, and is accessible through the left side panel. It is the larger of the two convection blowers, and pushes air past the cast heat exchanger and into the room. This blower, along with blower #1, will come on within 10-15 minutes of ignition.

16.FEED SYSTEM

The feed system pulls pellets up the feed tube from the hopper, using a hollow auger spring, and drops them down the feed chute into the firepot. The feed rate is adjustable; for complete instructions read the fuel feed system in the cleaning and maintenance section of this manual. NOTE: The feed motor will not operate when the front door of the insert is open. If you are having fuel problems, check the following:

A.Check the ramp in the firepot to see that it is free of fuel or other materials.

B.Check the set screw on the end of the motor shaft to see that it is tight and not slipping.

C.Check the electrical power to the motor.

D.Check the vacuum switch hose connections.

17.IGNITER

A.The igniter is located in the chamber at the bottom of the firepot. It is only on during the ignition cycle, and is usually on for the first two minutes and not more than four minutes.

NOTE: The element on the igniter is extremely brittle. Be very careful in handling it.

B.Check the wire leads to the igniter for loose or bad connections (ceramic wire nuts).

NOTE: Unplug insert before checking wire nuts.

18.FIREPOT

A.Clean the firepot (see section on cleaning and maintenance on page 13).

B.Make sure the cleanout plate in the bottom of the firepot is pushed in all the way.

C.Check the gasket between the firepot and the firebox bottom. A bad seal will affect the ignition time and the flame height.

19. DOOR GASKET

Check the door gasket to see that the door is completely closed and there are no air leaks. This can be done by closing the door on a piece of paper and checking that the paper is firmly held in place. You should have resistance when you try to pull the paper away.

NOTE: If no resistance is found, the door handle assembly needs to be adjusted or rope seal needs to be replaced.

20.HEAT EXCHANGER

There is one cast heat exchanger mounted on the right side of the firebox. Refer to cleaning and maintenance section in this manual for cleaning instructions (page 13).

Page 16

1100-I specifications

The Quadra-Fire 1100-I is a renowned wood-burning insert, designed to deliver robust performance and efficiency for homeowners looking to enhance their heating solutions. Known for its sleek finish and effective heating capabilities, this model is an excellent choice for those who want to experience the warmth and ambiance of a traditional wood fire.

One of the standout features of the Quadra-Fire 1100-I is its impressive heating capacity. With the ability to heat spaces up to 2,000 square feet, it makes an ideal option for medium to large homes. This wood insert boasts a nominal output of 65,000 BTUs, providing sufficient warmth even in the coldest winters. Its efficient design allows for long burn times of up to 10 hours, ensuring that you can enjoy continued warmth throughout the night without the need for constant refueling.

A critical technology incorporated in the Quadra-Fire 1100-I is its Advanced Combustion System. This system utilizes a secondary combustion process that minimizes emissions and maximizes efficiency. As the fire burns, it re-burns the gases and particulates that would typically escape into the atmosphere, resulting in a cleaner and more environmentally friendly burn. This feature not only reduces the impact on the environment but also enhances fuel efficiency, saving homeowners money on wood consumption.

The insert features a large ceramic glass door that allows for a captivating view of the fire, adding a cozy and inviting ambiance to any room. The glass is designed to withstand high temperatures without warping or discoloring, ensuring a clear view for years to come. Additionally, the Quadra-Fire 1100-I offers an easy-to-use airflow control system, allowing you to adjust the flame and heat output according to your preferences, making it easy to manage your heating needs throughout the day.

Installation of the Quadra-Fire 1100-I is straightforward, as it is designed to fit into existing fireplaces, eliminating the need for extensive renovations. The unit is also available with several finishing options, allowing homeowners to choose a look that complements their interior design.

In summary, the Quadra-Fire 1100-I is an ideal wood-burning insert for those seeking efficiency, environmental consciousness, and aesthetic appeal. With its powerful heating ability, advanced combustion technology, and striking design, it stands out as a reliable and attractive choice for anyone looking to add a wood-burning solution to their home.