Procom ML100TPA, ML060HPA, ML100HPA Operating Your Heater, Pilot/Ign, To Turn OFF GAS to Appliance

Page 11

OPERATING YOUR HEATER

Manual Control Models:

ML060HPA,ML100HPA

LIGHTING

INSTRUCTIONS

1. STOP! Read the safety information on the side of heater.

2.Check that gas supply to heater is on.

3.Push in gas control knob slightly and turn clockwise to the OFF position. ( see Figures 16 & 17)

4.Wait five (5) minutes to clear out any air. Then smell for gas, including near the floor. If you smell gas, STOP!

Follow “B” in the safety information on the side of the heater. If you do not smell gas, go to the next step.

5.Push in gas control knob

s l i g h t l y

a n d

t u r n

counterclockwise

to

“PILOT/IGN”

and depress for

five(5) seconds

 

NOTE: The first time that the heater is operated after connecting the

gas supply , the control knob should be depressed for about thirty

(30)seconds. This will allow air to bleed from the gas system.

6.With control knob pressed in, push down and release the ignitor button. This will light pilot. If needed, keep pressing ignitor button until pilot lights.

7.Keep control knob depressed for ten (10) seconds after lighting pilot. If pilot goes out, repeat steps 5,6 and 7.

8.To select the desired heating level, partially press down the control knob slightly and rotate

counterclockwise . Release the downward pressure on the knob while continuing to turn until the knob locks at the desired setting position. Do not operate between locked positions.

TO SELECT

HEATING LEVEL

WARNING: When running heater,set control knob at ON, LOW or HIGH locked positions.(see Figure 19 & 20) N e v e r s e t c o n t r o l k n o b between locked positions. Poor combustion and higher levels of carbon monoxide may result.

CAUTION: Do not try to adjust heating levels by using the equipment shutoff valve.

Slightly press in control knob and

turn counterclockwise to the ON, LOW or HIGH positions(see Figure 19 & 20).

IMPORTANT: Release downward pressure while turning control knob. Control knob will lock at the desired position.

Figure 16 - Control Knob In The OFF Position

Figure 17 - Control Knob In The OFF Position

Figure 18 - Pilot

ML060HPA

Figure 19 - Burner Patterns

ML100HPA

Figure 20 - Burner Patterns

TO TURN OFF

GAS TO APPLIANCE

Shutting Off Heater

1.Turn control knob clockwise

to the OFF position.

2.Turn off all electric power to the appliance if service is to be performed.

Shutting Off Burner Only (Pilot Stays Lit)

Turn control knob clockwise to the PILOT/IGN position.

MANUAL LIGHTING

PROCEDURE

1.Remove lower front panel (see Figure 7 page 7).

2.Follow steps through 5 under Lighting Instructions.

3.With control knob pressed in, strike match. Hold match to pilot until pilot lights.

4.Keep control knob pressed in for 30 seconds after lighting pilot. After 30 seconds, release control knob.Follow step 8 under Lighting Instuctions .

5.Replace lower front panel.

1 1

Page 10 Page 12
Image 11
Page 10 Page 12
Contents ML060HPA ML100HPA ML100TPA OWNER’S Operation and Installation ManualCarbon Monoxide Poisoning P O R TA N T Read thisProduct Identification Determining if you have a Confined or Unconfined Space Fresh AIR for Combustion and VentilationProviding Adequate Ventilation Determining FRESH-AIR Flow for Heater LocationVentilation Air from Inside Building AIR for Combustion Ventilation Ventilation AIRLocating Heater InstallationInstallation Needs Ventilation AIRMethods For Attaching Mounting Bracket To Wall InstallationFastening Heater to Wall Mounting Bracket Removing Lower Front Panel Of HeaterAttaching to Wall Anchor Method Installing Bottom Mounting ScrewTypical Inlet Pipe Diameters Connecting to GAS SupplyImportant Install Checking GAS Connections For Your Safety Read Before LightingShutting Off Heater Operating Your HeaterPILOT/IGN To Turn OFF GAS to ApplianceStays lit OFFShutting Off Burner Only pilot Operating Heater Cleaning MaintenanceInspecting Burner Observed Problem Possible Cause Remedy TroubleshootingMaintenance Page 13 or Heater produces unwanted odors Models ML060HPA,ML100HPA, ML100TPA SpecificationsParts Under Warranty Illustrated Parts Breakdown ML060HPA Parts Available not Shown Parts List ML060HPAKEY Part Number Description QTY ODSML100HPA Illustrated Parts BreakdownParts List ML100HPA ML100TPA Part List ML100TPA

ML060HPA, ML100TPA, ML100HPA specifications

Procom's ML100TPA, ML100HPA, and ML060HPA are cutting-edge amplifiers designed to enhance communication capabilities across various applications. These models are particularly popular in the fields of radio and communication technology, providing reliable performance and superior signal quality.

The ML100TPA is a high-performance, compact transmitter amplifier. It boasts an impressive power output of up to 100 watts, making it suitable for long-range communications. One of its standout features is its wide frequency range, accommodating multiple bands, which allows users to switch between applications seamlessly. The built-in thermal management system ensures stable operation even under heavy loads, preventing overheating and enhancing durability.

The ML100HPA is another powerful offering from Procom, specifically tailored for high-power applications. With a power output similar to the ML100TPA, this amplifier delivers robust performance while maintaining a compact form factor. It includes advanced features such as automatic gain control, ensuring consistent output levels regardless of input variations, which is essential for maintaining signal integrity. Additionally, the ML100HPA integrates an innovative protection circuit that safeguards against mismatches and overloads, enhancing reliability in demanding environments.

On the other hand, the ML060HPA is designed for applications where size and weight are critical considerations without compromising on performance. This model offers a power output of 60 watts, making it ideal for portable setups and mobile operations. Despite its smaller size, the ML060HPA does not skimp on features, including a high-efficiency design that maximizes battery life in mobile applications. It is also equipped with advanced filtering technologies to minimize harmonic distortion and maintain clear communication.

All three models leverage Procom's proprietary technologies, ensuring that they meet the stringent requirements of modern communication systems. They are built with high-quality components to ensure longevity and consistent performance in various environments, from urban settings to remote locations. Moreover, each model is user-friendly, with easy setup and configuration options, making them accessible for both novice and seasoned users.

In summary, the Procom ML100TPA, ML100HPA, and ML060HPA amplifiers represent the pinnacle of communication technology, each offering unique features tailored to specific user needs. Their combination of power, efficiency, and advanced technology makes them invaluable tools for enhancing communication capabilities across a wide range of applications. Whether for broadcasting, emergency communications, or mobile operations, Procom's amplifiers provide the quality and reliability needed to keep users connected.
Top Page Image Contents