Napoleon Fireplaces GVFS20N, GVFS20P manual Operation, Operating Instructions

10

OPERATION

OPERATING INSTRUCTIONS

If heater shuts off, do not relight until you pro- vide fresh air. If heater keeps shutting off, have it serviced. Keep burner and control compartment clean.

When lit for the fi rst time, the fireplace will emit a slight odour for a few hours. This is a normal temporary condition caused by the curing of the logs and the “burn-in” of internal paints and lubricants used in the manufacturing process and will not occur again. After extended periods of non-operation such as following a vacation or a warm weather season, the fireplace may emit a slight odour for a few hours. This is caused by dust particles burning off. In both cases, open a window to suffi ciently ventilate the room.

FOR YOUR SAFETY READ BEFORE LIGHTING:

WARNING: IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY, A FIRE OR EXPLOSION MAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE.

A. This fi replace is equipped with a pilot which must be lit by hand while following these instructions exactly.

B. Before operating smell all around the fi replace area for gas and next to the fl oor because some gas is heavier than air and will settle on the fl oor.

C. Use only your hand to push in and turn the gas control knob. Never use tools. If the knob will not push in and turn by hand, do not try to repair it. Call a qualifi ed service technician. Force or attempted repair may result in a fi re or explosion.

D. Do not use this fireplace if any part has been under water. Immediately call a qualifi ed service technician to inspect the fi replace and replace any part of the control system and any gas control which has been under water.

• Do not try to light any appliance.

WHAT TO DO IF YOU SMELL GAS:

•Do not touch any electric switch; do not use any phone in your building.

•Immediately call your gas supplier from a neighbour’s phone. Follow the gas supplier’s instructions.

•If you cannot reach your gas supplier, call the fi re de- partment.

When lighting and re-lighting, the gas knob cannot be turned from pilot to off unless the knob is depressed.

	N	O
	O	F
	T	F
	OLI
	P
OXYGEN DEPLETION SENSOR	GAS KNOB

LIGHTING INSTRUCTIONS

1.STOP! Read the above safety information on this label.

2.Set the thermostat to lowest setting.

3.Turn off all electric power to the fi replace.

4.Open the control door. Turn the gas knob clockwise to off.

5.Wait five (5) minutes to clear out any gas. If you smell gas including near the fl oor, STOP! Follow “B” in the above safety information on this label. If you don’t smell gas go to the next step.

6.Find pilot located in front of the back log.

7.Turn gas knob counter-clockwise to pilot.

8.Depress and hold gas knob while lighting the pilot with the push button ignitor. Keep knob fully depressed for one minute, then release. If pilot does not continue to burn repeat steps 3 through 7.

9.With pilot lit, turn gas knob counter-clockwiseto on. When the pilot has been turned off, ignition of the main

burner may be delayed from 1-2 minutes.

When the pilot has been left burning, ignition of the main burner should occur almost immediatley.

10.If equipped with remote on-off switch, main burner may not come on when you turn the valve to on. Remote switch must be in the on position to ignite burner.

11.Turn on all electric power to the fi replace.

TP TH		GAS KNOB AT OFF
TP
OL
TH	N	O
		F
HI	O	F
		IP
		TOL
P
TOLI

TO TURN OFF GAS

1.Turn off all electric power to the fi replace if service is to be performed.

2.Push in gas control knob slightly and turn clockwise to off. Do not force.

W415-0559 / 02.15.06