Monessen Hearth DEB30, DEB20 manual Special Requirements

Page 39

SPECIAL REQUIREMENTS CONTINUED

2.APPROVED CARBON MONOXIDE DETECTORS. Each carbon monoxide detector as required in accordance with the above provisions shall comply with NFPA 720 and be ANSI/UL 2034 listed and IAS certified.

3.SIGNAGE. A metal or plastic identification plate shall be permanently mounted to the exterior of the building at a minimum height of eight (8) feet above grade directly in line with the exhaust vent terminal for the horizontally vented gas fueled heating appliance or equipment. The sign shall read, in print size no less than one-half (1/2) inch in size, “GAS VENT DIRECTLY BELOW. KEEP CLEAR OF ALL OBSTRUCTIONS.”

4.INSPECTION. The state or local gas inspector of the side wall horizontally vented gas fueled equipment shall not approve the installation unless, upon inspection, the inspector observes carbon monoxide detectors and signage installed in accordance with the provisions of 248 CMR 5.08(2)(a)1 through 4.

(b)EXEMPTIONS: The following equipment is exempt from 248 CMR 5.08(2)(a)1 through 4:

1.The equipment listed in Chapter 10 entitled “Equipment Not Required To Be Vented” in the most current edition of NFPA 54 as adopted by the Board; and

2.Product Approved side wall horizontally vented gas fueled equipment installed in a room or structure separate from the dwelling, building or structure used in whole or in part for residential purposes.

(c)MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING SYSTEM PROVIDED. When the manufacturer of Product Approved side wall horizontally vented gas equipment provides a venting system design or venting system components with the equipment, the instructions provided by the manufacturer for installation of the equipment and the venting system shall include:

1.Detailed instructions for the installation of the venting system design or the venting system components; and

2.A complete parts list for the venting system design or venting system.

(d)MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING SYSTEM NOT PROVIDED. When the manufacturer of a Product Approved side wall horizontally vented gas fueled equipment does not provide the parts for venting the flue gases, but identifies “special venting systems,” the following requirements shall be satisfied by the manufacturer:

1.The identification of each “special venting system” shall include either the listing of the website, phone number or manufacturer’s address where the venting system installation instructions can be obtained; and

2.The “special venting systems” shall be Product Approved by the Board, and the instructions provided with that system shall include a parts list and detailed installation instructions.

(e)A copy of all installation instructions for the Product Approved side wall horizontally vented gas fueled equipment and all the venting instructions, parts lists, and/or all design instructions for the venting system shall remain with the appli- ance or equipment at the completion of the installation.

Page 38 Page 40
Image 39
Page 38 Page 40
Contents Models DEB20, DEB24, DEB30 Read and Save These InstructionsWhat to do if YOU Smell GAS Contents Important Safety Information InstallerOwner From What YOU will Need for Installation Getting StartedMake Sure YOU have Received ALL Parts Product Features and Specifications Natural GASPROPANE/LPG Ignition Controls PILOT/ODSThermal Generator General Installation Information CodesAdequate Combustion and Ventilation AIR BTU/Hr = 151/2 x 12 x 8 x 1000 = 29760 BTU/Hr Hearth Minimum Dimension Fireplace and Hearth DimensionsHeight of Restriction Minimum Depth of Fireplace/Firebox Placement in a Fireplace with a Restrictive BarrierSidewall and Ceiling Clearances Clearances and Height RequirementsClearances and Height Requirements Measuring Heat Resistant Material for Mantel Heater Clearances and Height RequirmentsExample The bottom of the mantel may project from the wall a Minimum Clearance above Combustible Flooring Floor ClearanceDamper Stop Installation Installing Vented ApplicationsBefore Fully Installing the Unit Before Installing the ApplianceInstalling Vented Applications Assembly ProcedurePlacing and Securing Appliance Flexible Tube Manual Shutoff Gas Supply Inlet Valve Connecting the GASManual Control Figure Checking GAS PressureElectrical Wiring MILLI-VOLT Connecting Optional Wall Switch or ThermostatATE Installing T-STAT Sensor Option Sold Separately Connecting Remote ReceiverInstalling T-Stat Sensor to DEB Base With Screw Provided Operation of Thermostat Sensor Checking System OperationComplete MILLI-VOLT System Check Installing Logs on Grate See Figures 25 LOG PlacementMILLI-VOLT Control Flame AppearancePlacing the Decorative Rock Checking the Pilot FlameOperating Instructions Checking the Burner FlameWhat to do if YOU Smell GAS Operating InstructionsManual Control Lighting Instructions MILLI-VOLT Control Lighting Instructions Cleaning and Servicing Operating Instructions and Cleaning and ServicingObserved Problem Possible Cause Remedy TroubleshootingODS/pilot lights, but flame Burner Assembly Replacement PartsDEB20 DEB24/DEB30 Replacement Parts ListDEB20 DEB24 DEB30 LogsSpecial Requirements Special Requirements Lifetime Warranty Five Year WarrantyBasic Warranty

DEB20, DEB30 specifications

Monessen has long been synonymous with quality and innovation in the hearth industry, and the Monessen Hearth DEB20 and DEB30 models are prime examples of their commitment to excellence. These direct vent gas fireplaces provide a stylish and efficient solution for heating and enhancing the ambiance of any home.

One of the standout features of both the DEB20 and DEB30 is their versatile design. Available in different sizes, the DEB20 is tailored for smaller spaces, while the DEB30 is ideal for larger areas, ensuring that homeowners can select a model that fits their specific needs. Both units are equipped with a minimalist design that allows them to seamlessly integrate into various decor styles, from modern to traditional.

Another important characteristic of the DEB series is their use of advanced technology for efficient operation. The direct vent system ensures that combustion gases are vented outside, providing a safer and cleaner indoor environment. This feature not only enhances the air quality in your home but also allows for flexible installation options, as venting can be engaged through walls or roofs.

The Monessen DEB20 and DEB30 models also boast a variety of aesthetic customizations. They come with an array of decorative options, including different media choices like glass, logs, or stones, allowing homeowners to create a truly personalized look. Optional features such as remote control operation provide additional convenience, allowing users to adjust flame height and heat output at the push of a button.

Energy efficiency is another hallmark of these fireplaces. Both the DEB20 and DEB30 are designed to maximize heat output while minimizing gas consumption, making them an economical heating solution. They also feature adjustable flame settings to meet various heating requirements, ensuring that warmth can be tailored to personal preference.

In summary, the Monessen Hearth DEB20 and DEB30 units exemplify a marriage of style and function, driven by cutting-edge technology and thoughtful design. With their efficient heating capabilities, customizable aesthetics, and safe operation, these fireplaces offer a compelling choice for anyone looking to enhance their home's warmth and charm. Whether it's for cozy family gatherings or quiet evenings, the DEB series is sure to deliver comfort and elegance.
Top Page Image Contents