Installation

W385-0199

FIGURE1

Clean out ashes from the inside of the wood-burning fire- place. Make sure that the chimney and wood-burning fire- place are in a clean and sound condition and constructed of non-combustible materials. If necessary have any repair work done by a qualified person before installing the in- sert. Remove the existing fireplace damper or lock into an open position.

Using screws, attach the fireplace warning tag (W385-0199) to the inside of the firebox of the fireplace into which the insert is being installed.

WARNING: THIS FIREPLACE HAS BEEN CONVERTED FOR USE WITH A GAS FIREPLACE INSERT ONLY AND CANNOT BE USED FOR BURNING WOOD OR SOLID FUELS UNLESS ALL ORIGINAL PARTS HAVE BEEN REPLACED AND THE FIREPLACE IS RE-APPROVED BY THE AUTHORITY HAVING JURISDICTION.

ATTENTION: CE FOYER A ETE CONVERTI AFIN D'ETRE UTILISE SEULEMENT COMME FOYER ENCASTRE AU GAZ ET NE PEUT ETRE UTILSE POUR BRULER DU BOIS OU TOUT AUTRE COMBUSTIBLE SOLIDE, SANS QUE TOUTES LES PIECES ORIGINALES AIENT ETE REMPLACEES ET QUE LE FOYER SOIT APPROUVE DE NOUVEAU PAR LES AUTORITES AYANT JURIDICTION.

Line the chimney with a 3" or 4" diameter approved liner. With a 4" liner, an increaser must be connected between the dilution draft hood and the liner. Chimney installation must conform to both national and local code requirements. The liner must be continuous from the fireplace to the chimney cap.

FIGURE2

The sheet-metal parts of the fireplace, in which the gas fireplace insert is to be installed, must not be cut.

If the wood-burning factory-built fireplace has no gas access hole(s) provided, an access hole of 1½ inch or less may be drilled through the lower sides or bottom of the fireplace in a proper workman like manner. This access hole must be plugged with non-combustible in- sulation after the gas supply line has been installed.

Ensure that existing chimney cleanouts fit properly. The refractory, glass doors, screen rails, screen mesh and log grates may be removed from the fireplace be- fore installing the gas fireplace insert.

Smoke shelves, shields and baffles may be removed if attached by mechanical fasteners.

The ventilation openings in the fireplace may be ob- structed by the backer plates, aluminium trim etc. but these parts are not to be applied so as to have an air- tight seal.

Remove the securing screw from the front of the dilution plate. Push the dilution draft hood out of the securing clips and attach the liner using 3 screws equally spaced. Pack insulation around the liner at the damper area to prevent air flow from entering the chimney. Move the insert into the centre of the woodburning fireplace making sure that the dilution draft hood inserts back into its securing clips. Level using the four leveling screws located front and back on either side of the fireplace base. Leveling the insert will eliminate rocking or excessive noise when the fan is in operation. Replace the securing screw to the front of the dilution plate.

FIGURE3

Install rigid black pipe, a flex connector, if local codes per- mit, or 1/2" type L, copper tubing with a 3/8" to 1/2" adapter and a shut off valve to the fireplace. Seal and tighten se- curely. The adapter will be required between the gas valve and the copper tubing or flex connector. Do not kink flex- ible connector! Check for gas leaks by brushing on a soap and water solution. Do not use open flame!

W415-0061 / B / 01.11.05

GI 3600-N, GI 3600-P specifications

The Napoleon Fireplaces GI 3600-N and GI 3600-P are cutting-edge gas insert fireplaces designed to bring warmth, comfort, and a modern aesthetic to any living space. Renowned for their efficiency and innovative features, these models set a new standard in home heating.

One of the standout features of the GI 3600-N and GI 3600-P is their impressive heat output. With a maximum input of 36,000 BTUs, they can efficiently heat areas up to 2,000 square feet, making them an ideal choice for both large and small rooms. The adjustable flame height allows users to customize the ambiance, ranging from a minimal decorative flame for a cozy evening to a roaring fire for colder nights.

These gas inserts incorporate Napoleon’s advanced modern technology, including the patented PHAZER™ log set, which is crafted from high-quality materials to provide a lifelike appearance. This technology not only enhances the visual appeal but also improves combustion efficiency. The GI 3600 series also features a highly efficient design, boasting an impressive thermal efficiency rating of up to 82%. This means less fuel consumption and lower heating bills, making it an environmentally friendly option.

Installation versatility is another significant characteristic of the GI 3600 models. The inserts can fit seamlessly into a variety of existing fireplaces, transforming dated or non-functional units into stylish and efficient heating solutions. Both models come with a choice of front designs and finishes, allowing homeowners to customize their fireplaces to match their home decor.

User-friendly controls are a hallmark of the GI 3600-N and GI 3600-P. They come equipped with a remote control option, enabling straightforward operation from the comfort of your couch. Additionally, the fireplaces feature a convenient setup for optional Wi-Fi connectivity, allowing for operation via smartphone apps for ultimate convenience.

Safety is paramount with these inserts, which include features like a safety shut-off system and a glass front that remains cool to the touch, ensuring peace of mind, especially in homes with children or pets.

In summary, the Napoleon Fireplaces GI 3600-N and GI 3600-P offer a perfect blend of style, efficiency, and advanced technology. With their impressive heating capabilities, customizable features, and focus on safety, they are an excellent addition to any home looking to enhance its aesthetic while enjoying the comforting embrace of a gas fireplace.