Vermont Casting 2463 manual Maintenance, Cleaning the Glass, Adjust the Door Latch

Page 21

Dutchwest

Maintenance

Keep Your Stove Looking New

and Working Its Best

Care of the Cast Iron Surface

An occasional dusting with a dry rag will keep the painted cast iron of your Dutchwest Convection Heater looking new.

If the paint needs retouching, allow the stove to cool completely. Wire-brush areas needing to be painted. Remove non-painted components such as air controls or cover them with masking tape. Touch up the stove with high temperature stove paint available from your local dealer. Apply the paint sparingly. Two light coats

are better than one heavy one.

Cleaning the Glass

You will find that most of the carbon deposits on the glass will burn off regularly during hot fires. You can wipe fly ash from the glass when hot using a crumpled piece of dry newspaper. Never use liquid cleaning agents on hot glass. If you wish to clean the glass more thoroughly, follow this procedure:

•Be sure the glass is completely cool.

•Use a glass cleaner especially made for this pur- pose.

•Dry the glass completely.

Adjust the Door Latch

The door latches must close tightly to ensure a good seal between the each door and the stove plates. With time and use, the door latches will require periodic adjustment. Follow this procedure: (Fig. 26)

1.Loosen the small locking nut with an open end wrench.

2.Use the allen wrench (included with the stove) to turn the striker screw clockwise one quarter-turn and close the door to test the engagement. The door latch should engage tightly when closed. Make further adjustments in small increments.

3.When the striker screw is properly adjusted, tighten the small locking nut against the pawl without allow- ing the striker screw to turn.

Small Lock- ing Nut

Door

Striker

Screw

Pawl

Large Lock- ing Nut

Set Screw

ST439

Fig. 26 Door latch adjustment.

Remove the old gasket by pulling gently, but firmly.

ST440

Fig. 27 Door gasket.

Test And Repair the Door Gaskets

Air leaks can be caused by low spots in the door gas- kets. To locate such low spots, close each door on a slip of paper and attempt to pull the paper free. If the paper slips out without tearing, the gasket isn’t snug enough at that spot.

If the seal cannot be improved by adjusting the door latch, try shimming the gasket. Pack a small quantity of cement or a smaller diameter gasket into the channel beneath the gasket to lift the main gasket and thereby improve its contact with the door frame.

If shimming does not improve the seal, replace the gasket following these steps:

1.Remove the original gasket by grasping an end and pulling firmly.

2.Wearing safety goggles, use a wire brush or the tip of a screwdriver to clean the channel of any remain- ing cement or bits of gasket.

7001219

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Convection Heater Model Table of Contents Dutchwest, Model SpecificationsInstallation Chimney TypesMasonry Chimneys Two Types of Connector Guidelines for Installing the Chimney ConnectorSingle-Wall Connector Prefabricated ChimneysDouble-Wall Connector Assembling Single-Wall Chimney ConnectorSecuring the Connector To a Prefabricated Chimney Securing the Connector to a Masonry Chimney Freestanding InstallationsFireplace Installations Above the Fireplace Wall Pass-Throughs Fireplace Installations Through the FireplaceFloor Protection Fireplace InstallationsFireplace Installation Clearances Keep the Stove a Safe Distance From Surrounding MaterialsSafe Ways to Reduce Clearances Unprotected Surfaces Protected Surfaces Clearance Chart Reference DiagramsStove and Chimney Connector Clearance Charts Unprotected Surfaces Protected Surfaces Wall Heat Shield Dimensions Assembly Unpack the PartsAttach the Legs and Heat Shield Operation Heater Controls and Features Air ControlsLoad Doors Damper FunctionSuccessful Wood Burning Burn Only High-Quality FuelHow to Build and Maintain a Wood Fire Loading Wood Use the Air Control Settings That Work Best for YouLighting the Fire Break-in FiresReloading and Reviving the Fire Further suggestionsSafe Ash Handling Cleaning the Glass MaintenanceAdjust the Door Latch Test And Repair the Door GasketsPrimary Air Control Adjustment Damper AdjustmentRepair Missing Cement in Seams Avoid Damaging the Glass Door PanelInspect Regularly, Clean As Required Cleaning the Chimney SystemMaintenance Schedule Annual Spring CleaningYearly Spring Cleaning Draft Management Single Venting Backpuffing Draft TestingFuel CreosoteDutchwest Convection Heater Dutchwest Convection Heater Dutchwest Dutchwest Warranty CFM Specialty Home Products

2463 specifications

The Vermont Casting 2463 is a premium wood-burning stove that exemplifies both efficiency and craftsmanship, appealing to homeowners looking for a blend of performance and aesthetic charm. Designed with both traditional and modern aesthetics in mind, this stove fits seamlessly into a variety of home decors while providing exceptional heating capabilities.

One of the standout features of the Vermont Casting 2463 is its robust construction, which includes a heavy cast iron body. This material not only ensures longevity and durability but also provides superior heat retention, allowing the stove to radiate warmth even after the fire has diminished. The intricate design of the cast iron exterior adds an elegant touch, making it a focal point in any room.

The 2463 incorporates advanced combustion technology that enhances its efficiency. The double-combustion system ensures that smoke and particulates are burned at a higher temperature, which significantly reduces emissions and increases the overall efficiency of the burn. This not only supports eco-friendly heating but also allows users to enjoy longer burn times, minimizing the frequency of reloading the stove.

Another remarkable characteristic of the Vermont Casting 2463 is its large viewing window, which offers a captivating view of the flames, enhancing the ambiance of any space. The stove features an air wash system that keeps the glass clean, ensuring an unobstructed view of the fire while providing optimum efficiency.

Ease of use is another key aspect of the 2463 design. It includes a straightforward air control system that allows users to easily adjust the intensity of the flame and heat output to suit their preferences. The stove also features a removable ash pan, making clean-up a hassle-free task.

Furthermore, the Vermont Casting 2463 is EPA-certified, meaning it meets stringent environmental standards for emissions. This certification not only underscores the stove's commitment to sustainability but also allows homeowners to enjoy the inviting warmth of a wood fire while adhering to environmental regulations.

In summary, the Vermont Casting 2463 wood stove combines traditional craftsmanship with cutting-edge technology to create a powerful and efficient heating solution. With its durable construction, sophisticated design, user-friendly features, and eco-friendly performance, it is an excellent choice for those seeking to enhance their home's comfort and aesthetic appeal.
Top Page Image Contents