Vermont Casting 2463 Securing the Connector to a Masonry Chimney, Freestanding Installations

Page 7

Securing the Connector to a Masonry Chimney

The Model 2463 may be connected to either a free- standing masonry chimney or a masonry fireplace chimney.

Freestanding Installations

If the chimney connector must pass through a combus- tible wall to reach the chimney, follow the recommenda- tions in the wall pass-through section that follows.

The opening through the chimney wall to the flue (the “breech”) must be lined with either a ceramic or metal cylinder, called the “thimble”, which is securely cemented in place. (Fig. 7) Most chimney breeches incorporate thimbles, but check to be sure the fit is snug and the joint between thimble and chimney wall firmly cemented.

A special piece called the “thimble sleeve,” slightly smaller in diameter than the standard connector and most thimbles, will ease the removal of the chimney connector system for inspection and cleaning. Thimble sleeves should be available from your local dealer.

To install a thimble sleeve, slide it into the breech until it is flush with the inner flue wall. Don’t extend it into the actual flue passage, as that could interfere with the draft.

The thimble sleeve should protrude 1-2” (25-51 mm) into the room. Use furnace cement and thin gasketing to seal the sleeve in place in the thimble. Secure the chimney connector to the outer end of the sleeve with

sheet metal screws.

Fireplace Installations -

Above the Fireplace

In this installation, the chimney connector rises from the stove, turns 45 degrees, and goes back into the fireplace chimney. The liner of the fireplace chimney should extend at least to the point at which the chimney connector enters the chimney. Follow all the guidelines for installing a chimney connector into a freestanding masonry chimney, and pay special attention to these additional points:

•Check the stove and chimney connector clearances to combustible mantel or trim materials. Use the necessary combination of mantel, trim, and connec- tor heat shields to provide the required clearances. (Fig. 8)

•Double-check connector clearance from the ceiling.

•The fireplace damper must be closed and sealed to prevent room air from being drawn up the flue, reducing the draft. However, it must be possible to re-open the damper to inspect or clean the chimney.

Dutchwest

Thimble

Flue Liner

 

Thimble

 

Sleeve

 

Elbow

 

Chimney

 

Connector

Flue

 

 

ST243a

Fig. 7 The thimble, made of either ceramic or metal, must be cemented in place securely.

Masonry Wall

Ceramic Flue Liner

Chimney

Connector Shield

Chimney Connector

Block-Off

Plate

ST244a

Fig. 8 The connector enters flue above the fireplace. If the clearance between the chimney connector and either the mantel and/or the ceiling is inadequate, special protective shields will be required.

Flue Liner

 

Extend Chimney

 

Connector to the

Damper

First Tile of the Flue

Plate is

Liner

Removed

 

or Locked

Observe

in Open

Position

Miniumum Clearances

 

 

Close Off

 

the Damper

 

Opening with

 

Sheet Metal

ST245a

and Sealant

 

Fig. 9 The connector passes through the fireplace to enter flue. Special Fireplace Adapter Kits to simplify fireplace instal- lations are available from your local dealer.

7001219

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Convection Heater Model Table of Contents Dutchwest, Model SpecificationsChimney Types InstallationMasonry Chimneys Prefabricated Chimneys Guidelines for Installing the Chimney ConnectorTwo Types of Connector Single-Wall ConnectorAssembling Single-Wall Chimney Connector Double-Wall ConnectorSecuring the Connector To a Prefabricated Chimney Freestanding Installations Securing the Connector to a Masonry ChimneyFireplace Installations Above the Fireplace Wall Pass-Throughs Fireplace Installations Through the FireplaceFloor Protection Fireplace InstallationsKeep the Stove a Safe Distance From Surrounding Materials Fireplace Installation ClearancesSafe Ways to Reduce Clearances Unprotected Surfaces Protected Surfaces Clearance Chart Reference DiagramsStove and Chimney Connector Clearance Charts Unprotected Surfaces Protected Surfaces Wall Heat Shield Dimensions Unpack the Parts AssemblyAttach the Legs and Heat Shield Operation Heater Controls and Features Air ControlsBurn Only High-Quality Fuel Damper FunctionLoad Doors Successful Wood BurningHow to Build and Maintain a Wood Fire Loading Wood Use the Air Control Settings That Work Best for YouFurther suggestions Break-in FiresLighting the Fire Reloading and Reviving the FireSafe Ash Handling Test And Repair the Door Gaskets MaintenanceCleaning the Glass Adjust the Door LatchAvoid Damaging the Glass Door Panel Damper AdjustmentPrimary Air Control Adjustment Repair Missing Cement in SeamsAnnual Spring Cleaning Cleaning the Chimney SystemInspect Regularly, Clean As Required Maintenance ScheduleYearly Spring Cleaning Draft Management Creosote Draft TestingSingle Venting Backpuffing FuelDutchwest Convection Heater Dutchwest Convection Heater Dutchwest Dutchwest Warranty CFM Specialty Home Products

2463 specifications

The Vermont Casting 2463 is a premium wood-burning stove that exemplifies both efficiency and craftsmanship, appealing to homeowners looking for a blend of performance and aesthetic charm. Designed with both traditional and modern aesthetics in mind, this stove fits seamlessly into a variety of home decors while providing exceptional heating capabilities.

One of the standout features of the Vermont Casting 2463 is its robust construction, which includes a heavy cast iron body. This material not only ensures longevity and durability but also provides superior heat retention, allowing the stove to radiate warmth even after the fire has diminished. The intricate design of the cast iron exterior adds an elegant touch, making it a focal point in any room.

The 2463 incorporates advanced combustion technology that enhances its efficiency. The double-combustion system ensures that smoke and particulates are burned at a higher temperature, which significantly reduces emissions and increases the overall efficiency of the burn. This not only supports eco-friendly heating but also allows users to enjoy longer burn times, minimizing the frequency of reloading the stove.

Another remarkable characteristic of the Vermont Casting 2463 is its large viewing window, which offers a captivating view of the flames, enhancing the ambiance of any space. The stove features an air wash system that keeps the glass clean, ensuring an unobstructed view of the fire while providing optimum efficiency.

Ease of use is another key aspect of the 2463 design. It includes a straightforward air control system that allows users to easily adjust the intensity of the flame and heat output to suit their preferences. The stove also features a removable ash pan, making clean-up a hassle-free task.

Furthermore, the Vermont Casting 2463 is EPA-certified, meaning it meets stringent environmental standards for emissions. This certification not only underscores the stove's commitment to sustainability but also allows homeowners to enjoy the inviting warmth of a wood fire while adhering to environmental regulations.

In summary, the Vermont Casting 2463 wood stove combines traditional craftsmanship with cutting-edge technology to create a powerful and efficient heating solution. With its durable construction, sophisticated design, user-friendly features, and eco-friendly performance, it is an excellent choice for those seeking to enhance their home's comfort and aesthetic appeal.
Top Page Image Contents