Vermont Casting 1450 Securing the Single-wall Connector to a Masonry Chimney, Above the Fireplace

Page 7

Encore 1450 Non-Catalytic Woodburning Stove

Chimney Flue

Elbow

Flue Liner

 

Thimble Sleeve

Chimney Connector

Flue

Slip Pipe

Standard Connector

Oval to

Round Adapter

Thimble

Keep sleeve end flush with flue tile

ST243

Flue Collar

ST492

Fig. 6 An exploded view of the chimney connection in a free- standing masonry installation.

Securing the Single-wall Connector to a

Masonry Chimney

Both freestanding masonry chimneys and fireplace ma- sonry chimneys may be used for your installation.

Freestanding Installations

If the chimney connector must pass through a combus- tible wall to reach the chimney, follow the recommen- dations in the Wall Pass-Through section later in this manual.

The opening through the chimney wall to the flue (the “breech”) must be lined with either a ceramic or metal cylinder, called the “thimble”, which is cemented securely in place. Most chimney breeches incorporate thimbles, but the fit must be snug and the joint between the thimble and the chimney wall must be cemented firmly.

A special piece called the “thimble sleeve,” slightly smaller in diameter than standard connectors and most thimbles, will facilitate the removal of the chimney connector system for inspection and cleaning. Thimble sleeves are available from your local dealer.

To install a thimble sleeve, slide it into the breech until it is flush with the inner flue wall. Do not extend it into the actual flue passage, as this could interfere with the draft.

Fig. 7 The thimble, made of either ceramic or metal, must be cemented securely in place.

The thimble sleeve should protrude 1-2” (25-50mm) into the room. (Fig. 7) Use furnace cement and thin gasket- ing to seal the sleeve in place in the thimble. Secure the chimney connector to the outer end of the sleeve with sheet metal screws.

Without a thimble, a suitable length of chimney con- nector can be extended through the breech to the inner face of the flue liner, and cemented securely in place. Additional pieces of connector are then attached with sheet metal screws.

Fireplace Installations

The chimney connector may be connected to the chimney above the fireplace opening or through the fireplace.

Above the Fireplace

The Encore may be connected to a chimney above a fireplace opening. (Fig. 8) In such installations, the stove is positioned on the hearth in front of the fireplace and the chimney connector rises from the stove top and then angles ninety degrees back into the chimney. The chimney liner should extend to the point at which the chimney connector enters the chimney.

If the chimney connector from your installation enters the chimney above a fireplace, follow all the guidelines mentioned above for freestanding installations. In addi- tion, give special consideration to the following points:

•Check the clearance between the stove and the chimney connector, and any combustible trim or the mantel. Use the necessary combination of mantel, trim, and connector heat shields to achieve the required clearances.

•Check the clearance between the chimney con- nector and the ceiling. If no heat shields are used, the clearance should be at least 24” (610mm). To find out how much this clearance may be reduced with heat shields, refer to the clearance chart on Page 14.

30002425

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Encore Welcome Table of ContentsSpecifications Encore dimensionsOutside Air InstallationChimney Height Chimney Size What Kind of Chimney to UseMasonry Chimneys Prefabricated ChimneysSingle-wall Chimney Connectors Chimney Connector GuidelinesDouble-wall Chimney Connectors Above the Fireplace Securing the Single-wall Connector to a Masonry ChimneyFreestanding Installations Fireplace InstallationsWall Pass-Throughs Through the FireplaceAn approved wall pass-through for the United States Floor ProtectionCanada Floor Protection for Fireplace InstallationsReducing Clearances Safely with Shields Keep the Stove a Safe Distance From Surrounding MaterialsWall Shields Fireplace Mantel and Trim Shields Chimney Connector Heat ShieldsConstruction Requirements Alcove InstallationsCutaway perspective of acolve installation Unprotected Surfaces Protected Surfaces Encore NC Clearance ChartBcef Encore Clearance DiagramsWall Shield Requirements for Common Installations Corner Parallel Installations Assembly Fan installation Kit # Fan Kit InstallationDamper Directs Air Flow Within the Stove OperationEncore NC Controls Single Air Control Regulates Heat Output and Burn TimeAndirons Help Protect the Glass Infrared Reflective Glass Panels For Clear Fire ViewingBurn Only High-Quality Wood Conditioning Your Stove Use the Air Control Settings That Work Best for YouStarting and Maintaining a Wood Fire Add larger pieces of wood as the fire begins to burn well Refuel While the Embers Are Still HotAsh Removal and Disposal Draft Management Back-puffing Draft TestingCreosote FuelMaintenance Tighten the Damper Handle as Needed Adjust the Door LatchesReplace the Stove Gaskets as Needed All Gasketed Construction Adjust the Door If NecessaryChimney System Creosote Chimney Connector Maintenance Schedule StoveEncore Non-Catalytic Woodburning Stove Encore Woodburning Stove Shell Enamel Parts Encore NC Model Limited Lifetime Warranty CFM Corporation

1450 specifications

The Vermont Casting 1450 is a highly regarded wood stove model that exemplifies efficiency and craftsmanship in home heating solutions. Known for its robust construction and innovative technology, the 1450 stands out in the world of traditional wood-burning stoves.

One of the defining features of the Vermont Casting 1450 is its impressive heating capacity. Designed to efficiently heat spaces of up to 1,800 square feet, it provides a cozy warmth that is perfect for both small and medium-sized homes. This model boasts an impressive BTU output, ensuring that it can effectively maintain comfortable temperatures during even the coldest months.

A notable characteristic of the 1450 is its use of advanced catalytic technology. This feature enhances the stove's ability to burn wood more completely, leading to higher efficiency and reduced emissions. The catalytic combustor allows for a longer burn time, meaning homeowners can enjoy consistent heat with less frequent refueling. This efficiency is complemented by a large firebox, which can accommodate logs up to 20 inches long, allowing for longer burn durations between reloads.

The Vermont Casting 1450 is crafted with durability in mind, utilizing high-quality materials that ensure longevity. The cast iron construction not only enhances the stove's aesthetic appeal but also contributes to its excellent heat retention properties. This means that once the stove is heated, it continues to radiate warmth long after the fire has died down.

Another appealing aspect of the 1450 is its ease of use. Featuring adjustable air controls, homeowners can easily regulate the burn rate and heat output to suit their needs. The stove also comes with a straightforward ash removal system, making maintenance hassle-free.

The Vermont Casting 1450 combines traditional design with modern innovation. Its classic style, complete with decorative cast iron details, adds a timeless elegance to any living space. With the functionality and aesthetic appeal it offers, this model is an excellent choice for those looking to enhance their home heating experience while embracing the charm of a wood-burning stove.

Overall, the Vermont Casting 1450 is a testament to the company's dedication to quality and performance, making it a favored choice among wood stove enthusiasts.
Top Page Image Contents