Teledyne LLG, LLD dimensions 3G. Swimming Pool Energy Saving Tips, 3H. Periodic Inspection

Page 19

Model LLG & LLD Pool and Spa Heater

Page 19

 

 

 

 

drowsiness (e.g., tranquilizers, antihistamines, or anticoagulants) should not use spas or hot tubs.

7.Prolonged immersion in hot water can induce hyperthermia.

Hyperthermia occurs when the internal body temperature reaches a level several degrees above the normal body temperature of 98.6°F (37°C). Symptoms include dizziness, fainting, drowsiness, lethargy, and an increase in the internal body temperature. The effects of hyperthermia include:

Lack of awareness of impending hazard

Failure to perceive heat

Failure to recognize need to leave spa

Physical inability to leave spa

Fetal damage in pregnant women

Unconsciousness resulting in a danger of drown- ing

3G. Swimming Pool Energy Saving Tips

Teledyne Laars offers the following recommen- dations to help conserve fuel and minimize the cost of

Table 7. Mineral Concentration Levels

Test

Recommended Level

 

 

Free chlorine

1.0 to 3.0 ppm

Bromine

3.0 to 5.0 ppm

pH

7.2 to 7.8

Total alkalinity (TA)

80 to 120 ppm

Calcium hardness (CH)

200 to 400 ppm

Langelier saturation index (LSI)

-0.5 to +0.5

Total dissolved solids (TDS)

Less than 2000 ppm

Cyanuric acid

30 to 150 ppm

Copper

0 ppm

 

 

operating your pool heater without sacrificing com- fort.

1.The American Red Cross recommends a maxi- mum water temperature of 78°F (25°C). Use an accurate pool thermometer. A difference of 4 degrees, from 78 to 82°F (25 to 28°C), will use as much as 40% more gas.

2.Carefully monitor the water temperature of your pool in the summertime. You can reduce heater usage due to warmer air temperatures.

3.Find the proper setting on the pool heater tem- perature control and use the TEMP-LOK to

discourage further adjustments.

4.Set the filter time clock to start the pump no earlier than 6:00 AM during the pool heating season. This is the time when nightly heat loss balances.

5.If the pool is only going to be used on weekends, reduce the heater temperature control setting by 8 or 10 degrees during the week. Reset it to the 78°F (25°C) level a day or so before you plan to use the pool.

6.During the winter or when on vacation for longer than a week, shut down the heater by following the shut-down instructions found on the inside of the heater.

7.Where possible, shelter the pool from prevailing winds with well-trimmed hedges or other land- scaping, cabanas, or fencing.

8.Always use a pool cover when practical. Besides providing a valuable safety feature, a pool cover will reduce heat loss, conserve chemicals, and reduce the load on filter systems.

3H. Periodic Inspection

WARNING

Improper installation or maintenance can cause nausea or asphyxiation from carbon monoxide in flue gases which could result in severe injury, or death.

3H-1. Owner Inspection

Teledyne Laars designs and constructs the Laars Lite heater to provide long performance life when installed and operated properly under normal condi- tions. The following basic guidelines are suggested for your inspection:

1.Keep the top and surrounding area of the heater clear of all debris.

2.Keep the heater area clean and free of all com- bustible materials, flammable liquids and vapors, as well as sanitization chemicals.

3.Do not use the heater if any part has been under water. Immediately call a qualified professional technician to inspect the heater and replace any part of the control system which has been sub- merged.

4.If the heater is equipped with a pressure relief valve, check for corrosion and make sure that water runs freely through it. If corrosion is found, replace the pressure relief valve.

Image 19
Contents 1A. Introduction Section1D. Technical Assistance 1C. Warranty2B. Field Assembly 1B. Description2C-2. Outdoor Installation 2C-1. Installation Information2C. Site Location Canada 2C-3. Flooring Typical Installation2D. Combustion and Ventilation Air Supply United States2E-1. General Instructions 2E. Gas Supply and Piping2F-1. General Information LLD Only 2F. Electrical Wiring2E-2. Special Precautions for Propane Gas LLG Only 2F-2. Auxiliary Time Clock Wiring LLD or LLGLLD Connection/Schematic Wiring Diagram LLG Connection/Schematic Wiring Diagram 2G. Water Flow System 2G-1. Flange InstallationHeat exchanger reversal 2G-2. Reversible Water ConnectionsTemperature sensing bulb 2G-5. Pressure Relief Valve 2G-3. Check Valve Installation2G-6. Adjusting the Pressure Switch 2G-4. Chlorinators, Ozone Generators Sanitizing Chemicals2G-7. Automatic Flow Control Valve 2G-8. Temperature Rise3B-1. Model LLD see 3B-2. Model LLG see 3B. Lighting and Shutdown Procedures2G-9. Adjusting the Manual Bypass Valve 3A. General InformationDo not try to light any appliance 3B-1. Model LLD Direct IgnitionWhat to do if YOU Smell GAS 3B-2. Model LLG Standing Pilot3D-2. Winterizing 3C. Setting the Temperature Control3D. Seasonal Care 3D-1. Spring and Fall Operation3E. Water Chemistry 3F. Spa/Hot Tub Safety Rules3D-3. Spring Start-up 3H. Periodic Inspection 3G. Swimming Pool Energy Saving Tips3H-1. Owner Inspection 4A. General Information 4B. Parts List3H-2. Professional Inspection LLD Direct Ignition **-LLG Standing Pilot See For detail Detailed view of Heat Exchanger Assembly D Detailed view of LLG Burner Tray Assembly EDetailed view of LLD Burner Tray Assembly E Page Laars Lite Limited Warranty

LLD, LLG specifications

Teledyne LLG, LLD is a prominent player in the field of advanced measurement and inspection systems. Based in the heart of the technology sector, Teledyne LLG combines cutting-edge engineering with innovative technologies to deliver high-performance solutions, particularly in the realms of optics and imaging.

One of the main features of Teledyne LLG is its commitment to precision. The company specializes in providing high-resolution sensors and imaging systems that cater to a variety of applications, including scientific research, industrial inspection, and aerospace. These sensors are designed to meet stringent performance standards, ensuring reliable data acquisition and analysis across diverse environments.

The technologies employed by Teledyne LLG are at the forefront of optical engineering. Their systems often utilize sophisticated algorithms and advanced signal processing techniques to enhance image quality and measurement accuracy. Innovations such as spectral imaging enable users to capture and analyze information beyond the visible spectrum, offering valuable insights for applications in fields like remote sensing and environmental monitoring.

Another characteristic that sets Teledyne LLG apart is its focus on integration and customization. Understanding that each application has unique requirements, the company offers tailored solutions that cater to specific needs. This flexibility allows clients from various sectors to leverage Teledyne LLG's technologies effectively, optimizing their operational workflows.

Teledyne LLG’s commitment to research and development ensures that its products continually evolve. The company invests significantly in exploring new materials, sensor designs, and imaging techniques. This proactive approach not only keeps them ahead of market trends but also ensures that their customers benefit from the latest technological advancements.

Moreover, Teledyne LLG places a strong emphasis on sustainability and efficiency. By developing systems that require less energy and produce less waste, the company not only addresses environmental concerns but also helps clients reduce operational costs.

In summary, Teledyne LLG, LLD stands out in the field of measurement and inspection through its precision, innovative technology, customized solutions, and commitment to sustainability. As industries continue to seek advanced solutions to meet modern challenges, Teledyne LLG remains dedicated to providing high-quality imaging and measurement systems that drive progress and innovation across multiple fields. With its strong focus on R&D and customer-centric solutions, Teledyne LLG is well-positioned to lead the future of optical technology and sensor development.