Vanguard Heating VMH26NR Check GAS Type, Installation Items, Locating Fireplace

Page 8

® VMH26NR

COMPACT CLASSIC HEARTH FIREPLACE

INSTALLATION

NOTICE: This heater is intended for use as supplemental heat. Use this heater along with your pri- mary heating system. Do not in- stall this heater as your primary heat source. If you have a central heating system, you may run system’s circulating blower while using heater. This will help circu- late the heat throughout the house. In the event of a power outage, you can use this heater as your primary heat source.

WARNING: A qualified ser- vice person must install fireplace. Follow all local codes.

WARNING: Never install the fireplace

•in a bedroom or a bathroom

•in a recreational vehicle

•where curtains, furniture, clothing, or other flammable objects are less than 36 inches from the front, top, or sides of the fireplace

•as a fireplace insert

•in high traffic areas

•in windy or drafty areas

CAUTION: This fireplace cre- ates warm air currents. These currents move heat to wall sur- faces next to fireplace. Installing fireplace next to vinyl or cloth wall coverings or operating fire- place where impurities (such as tobacco smoke, aromatic candles, cleaning fluids, oil or kerosene lamps, etc.) in the air exist, may discolor walls.

IMPORTANT:Vent-freefireplacesaddmois- ture to the air. Although this is beneficial, installing fireplace in rooms without enough ventilation air may cause mildew to form from too much moisture. See Air for Combustion and Ventilation, pages 5 through 7.

Note: Your Vanguard fireplace is designed to be used in zero clearance installations. Wall or framing material can be placed directly against any exterior surface on the rear, sides, or top of your fireplace, except where standoff spacers are integrally at- tached. If standoff spacers are attached to your fireplace, these spacers can be placed directly against wall or framing materials.

Use the dimensions shown for rough open- ings to create the easiest installation (see Built-In Fireplace Installation, page 9).

CHECK GAS TYPE

Use only natural gas. If your gas supply is not natural gas, do not install fireplace. Call dealer where you bought fireplace for proper type fireplace.

INSTALLATION ITEMS

Before installing fireplace, make sure you have the items listed below.

•piping (check local codes)

•sealant (resistant to propane/LP gas)

•manual shutoff valve *

•test gauge connection *

•ground joint union

•sediment trap

•tee joint

•pipe wrench

*An A.G.A. design-certified manual shutoff valve with 1/8" NPT tap is an acceptable alternative to test gauge connection. Pur- chase the optional A.G.A. design-certified manual shutoff valve from your dealer. See Accessories, page 26 and 27.

Note: If desired, purchase a four-sided brass trim kit for built-in installations. See Acces- sories, page 26 and 27.

LOCATING FIREPLACE

WARNING: Maintain the mini- mum clearances shown in Fig- ures 6 and 7. If you can, provide greater clearances from floor, ceiling, and joining wall.

You can recess firebox into the wall. You can also position fireplace in the optional cabinet or corner mantels. IMPORTANT: Only use optional cabinet or corner mantels specified in this manual. Purchase the op- tional mantel from your dealer (see Acces- sories, pages 26 and 27).

CAUTION: If you install the fireplace in a home garage

•fireplace pilot and burner must be at least 18 inches above floor.

•locate fireplace where moving vehicle will not hit it.

For convenience and efficiency, install fire- place

•where there is easy access for operation, inspection, and service.

•in coldest part of room.

An optional blower kit is available from your dealer. See Accessories, pages 26 and

27.If planning to use blower, locate fire- place near an electrical outlet.

CEILING

36" Minimum

6"

Minimum

From

Sides Of

Fireplace

Left

Right

Side

Side

FLOOR

Figure 6 - Mounting Clearances As Viewed

From Front of Fireplace Shown Built In

The Wall

CEILING

Top Of

Mantel Can

Be Flush36"

Minimum

With Wall

Right

Side

Left

Side

Figure 7 - Mounting Clearances As Viewed From Front of Fireplace Shown with Optional Mantel

8

104325

Page 7 Page 9
Image 8
Page 7 Page 9
Contents VENT-FREE Natural GAS What to do if YOU Smell GASSafety Information Compact Classic Hearth FireplaceProduct Features Remote Control AccessoriesProduct Identification Local CodesAssembly Installing LogAssembling Fireplace Assembling HoodAIR for Combustion and Ventilation Providing Adequate VentilationUnusually Tight Construction Confined and Unconfined SpaceDetermining if You Have a Confined or Unconfined Space AIR for Combustion VentilationDetermining FRESH-AIR Flow for Fireplace Location Ventilation Air From Outdoors Ventilation AIRVentilation Air From Inside Building Installation Installation ItemsCheck GAS Type Locating FireplaceBUILT-IN Fireplace Installation Rough Opening for Installing in WallAssembling Brass Trim Brass trim shipped with mantel Optional Mantel InstallationMantel Clearances for Built-In Installation Installing Blower Assembly Installing Blower Accessory GA3400TRemoving Upper Louver Assembly For Built-In Installation Follow steps 2 through 6 in Installing Blower Assembly,Attaching Wood Base to Solid Floor Connecting to GAS SupplyExtension Cord Connecting Fireplace to GAS Supply Installation Items NeededChecking GAS Connections Pressure Testing Gas Supply Piping SystemPressure Testing Fireplace Gas Connections Optional Wireless HAND- Held Remote Control Accessories Installing ReceiverInstalling 9-Volt Battery in Hand- Held Remote Control Unit Optional Wall Mounted Thermostat GWMT1Optional Wall Switch GWMS2 Thermostat Base Terminals W and RLighting Instructions For Your Safety Read Before LightingOperating Fireplace Manual Lighting Procedure Optional Remote Operation To Turn OFF GAS To ApplianceOperating Blower GWMS2 Wall Mounted Switch OptionalGWMT1 Wall Mounted Thermostat Optional Burner Flame Pattern Inspecting BurnerPilot Flame Pattern Troubleshooting Observed Problem Possible CauseObserved Problem Possible Cause Remedy Top Cleaning and Maintenance Service HintsTechnical Service Wiring DiagramAccessories Specifications Replacement PartsIllustrated Parts Breakdown VMH26NR4Parts List VMH26NRWarranty Information

VMH26NR specifications

The Vanguard Heating VMH26NR is an innovative heating solution designed to provide efficient warmth while prioritizing energy savings and user comfort. With its sleek design and advanced technologies, the VMH26NR stands out in the crowded market of heating appliances.

One of the main features of the VMH26NR is its powerful heating capability. Equipped with a robust heating element, it can produce a significant amount of warmth quickly, making it ideal for medium to large spaces. Whether you are heating a living room, office, or workshop, the VMH26NR ensures that you stay comfortable during the colder months.

Efficiency is another hallmark of this model. The VMH26NR employs cutting-edge energy-saving technologies that optimize power consumption. This not only reduces energy bills but also lessens the environmental impact associated with conventional heating methods. Users can enjoy a warm atmosphere while being conscious of their carbon footprint.

The VMH26NR also features a user-friendly digital thermostat, which allows for precise temperature control. Users can easily adjust the settings to their comfort level, ensuring that the space remains at an ideal temperature without unnecessary energy expenditure. The digital display provides clear readings, making it easy to monitor performance and settings.

For added convenience, the unit comes with a programmable timer, allowing users to schedule the heating periods according to their routines. This feature is particularly beneficial for those who want the heater to operate only when needed, further enhancing energy efficiency and user convenience.

Safety is a top priority in the design of the VMH26NR. It is equipped with several safety features, including overheat protection and a tip-over switch, which automatically shuts off the unit in case of accidents. This ensures peace of mind, especially in households with pets or young children.

The Vanguard Heating VMH26NR also boasts a compact, portable design that makes it easy to move from room to room. Its lightweight construction and built-in handles provide added portability, allowing users to enjoy warmth wherever it is needed most.

In conclusion, the Vanguard Heating VMH26NR is a powerful, efficient, and user-friendly heating solution. Its advanced features, safety mechanisms, and adaptability make it an excellent choice for anyone looking to enhance their comfort during the chilly seasons. Whether you are a homeowner or a business owner, the VMH26NR promises to deliver reliable performance and satisfaction.
Top Page Image Contents