Vanguard Heating VDDVF36STN/STP, VDDVF36PN/PP General Venting, Location of Vent Termination

Page 5

OWNER’S MANUAL

PRE-INSTALLATION

PREPARATION

Continued

1" (25mm)

Dia. Hole

GENERAL VENTING

These models are approved for use with Simpson Dura-Vent 6 5/8" direct-vent pipe components and terminations as well as both flex and rigid Vanguard vent components.

" /8

(600mm)5 23

40

 

 

 

 

Min.

(1029mm)

 

/

39 3/4"

 

2"

(1010mm)

 

 

Figure 7 - Rough Opening for Installing Peninsula Fireplace

 

 

(25mm)

 

 

1"

 

 

3"

2" (51mm)

 

(76mm)

Dia. Hole

(51mm)

 

 

 

 

2"

 

 

 

3" (76mm)

Figure 10 - Hole Locations For Gas Line and Electric Wires for Peninsula and See Thru Fireplaces

10"

(254mm) Square Min.

Your fireplace is approved to be vented either through the side wall, or vertically using the following guidelines:

Only use Vanguard or Simpson Dura-

 

Vent GS venting components or kits spe-

 

cifically approved for this fireplace.

• Minimum clearance between vent pipes

 

and combustible materials is 1" (25 mm),

 

except where stated otherwise.

• Combustible material may be flush with

 

the top front of fireplace with a maxi-

 

mum thickness of 3/4".

Do not recess venting terminals into a

 

wall or siding.

Install horizontal venting with a 1/4"

 

rise for every 12" of run toward the ter-

 

mination.

Platform Must Be

 

Solid, Flat, and

"

 

8

Fully Supported

5/

23

 

(600mm)

 

39 3/4"

 

(1010mm)

 

Min.

Height

Depends On

Installation

Figure 11 - Rough Opening for Installing Exterior Vent Terminal

• You may paint the vent terminal with

450°F (232°C) heat-resistant paint to co-

ordinate with the exterior finish.

• There must not be any obstruction such

as bushes, garden sheds, fences, decks,

or utility buildings within 24" from the

front of the termination cap.

• Do not locate termination cap where ex-

40 /

2"

(1029mm)

*

Figure 8 - Rough Opening for Installing Peninsula Fireplace on Platform

* As required by design as long as ceiling clearance is maintained.

Vertical Height

Depends on

Installation

90o Elbow

45o

Elbow

263/8"

(670mm)

Refer to Pages 8 through 14 for Horizontal and Vertical Installation Details

cessive snow or ice build up may occur.

Be sure to clear vent termination area af-

ter snow falls to prevent accidental block-

age of venting system. When using snow

blowers, do not direct snow towards vent

termination area.

LOCATION OF VENT

TERMINATION

When locating vent termination, it is impor- tant to observe the minimum clearances shown in Figure 13, page 6. You will avoid extra framing by positioning your fireplace against an already existing framing mem-

"

 

 

5/8

 

 

(600mm)

 

 

39 3/4"

23

 

 

(1010mm)

Min.

43 (1098mm)/4"

Figure 9 - Rough Opening for Installing See Thru Fireplace

Horizontal

Length Depends

on Installation

Figure 12 - Vent Opening Height

ber. The sides of the fireplace may be posi- tioned directly against combustible walls.

*Check with local codes or with the current CAN/CGA B149[.1 or .2] Installation Codes for Canada or the USA Installations follow the current National Fuel Gas Code, ANS Z223.1, also known as NFPA 54.

Continued

106918

5

Image 5
Contents What to do if YOU Smell GAS Check Local Codes Prior to InstallationGlossary Terms VDDVF36PN/PP and VDDVF36STN/STP SeriesBefore YOU Begin IntroductionSelecting Location Clearances PRE-INSTALLATION PreparationMantel Clearances FramingLocation of Vent Termination General VentingGeneral Venting Installation Precautions Venting InstallationInstallation Planning Installing Vent System in a ChaseSnorkel Termination Installation for Horizontal TerminationVent Pipe Connections Horizontal Venting Horizontal Termination ConfigurationsVenting with Two 90 Elbows Cathedral Ceiling Installation Installation for Vertical TerminationFlat Ceiling Installation Venting with One 90 Elbow Vertical Termination ConfigurationsVertical Venting Parts Lists for Venting InstallationVenting High AltitudeInstalling Receiver Wall Switch InstallationElectrical Hookup for Blower Accessory GAS Rating Type of GAS Natural PROPANE/LP GAS Line HOOK-UPInstalling LOG SET GAS Supply TestingBurner Flame Adjustment Pilot Assembly AdjustmentDecorative Facing Burner RemovalOperating Guidelines and Maintenance Instructions Operating Fireplace For Your Safety Read Before LightingLighting Instructions To Turn OFF GAS To ApplianceGhrc Operation Optional Remote OperationTechnical Service Service HintsReplacement Parts Wiring DiagramObserved Problem Possible Cause Remedy TroubleshootingObserved Problem Possible Cause Company Gas leak. See Warning statement Accessories Replacement Parts GAS Control Valve Refractory PiecesNatural 104496-01 14389 Propane/LP 104496-02 Black 105904-01DIRECT-VENT GAS Fireplace 106918 Warranty Information

VDDVF36STN/STP, VDDVF36PN/PP specifications

The Vanguard Heating VDDVF36PN/PP and VDDVF36STN/STP are premium direct vent gas fireplaces that seamlessly blend contemporary design with advanced heating technologies. These models are perfect for homeowners looking to enhance their living spaces while ensuring optimal warmth and comfort.

One of the key features of the VDDVF36 series is its powerful heating capacity. With a maximum input of 36,000 BTUs, these fireplaces can efficiently warm large rooms, making them an excellent choice for both new constructions and renovations. Their direct vent system allows for flexible installation options, as it can draw air from outside and exhaust gases without needing an existing chimney.

The design aesthetic of the VDDVF36PN/PP and VDDVF36STN/STP models is notably sleek and modern. Available in either a pristine perfect black finish or a striking stainless steel option, these units can complement a variety of interior styles. The large viewing area, framed by a stylish bezel, ensures that the flames are the focal point of the room, establishing a cozy ambiance.

Equipped with advanced electronic ignition, these fireplaces offer ease of use and reliability. The ignitor provides a fast and safe startup, eliminating the need for manual lighting and enhancing the user experience. Additionally, these units come with a built-in thermostatic control, allowing users to regulate temperatures effectively, ensuring consistent comfort while optimizing energy use.

The VDDVF36 series is also designed with safety in mind. An integrated safety shut-off system ensures that the fireplace will automatically turn off if any issues are detected, providing peace of mind for users. Furthermore, the screens and barriers are designed to prevent accidental contact with the flames, making them safe for households with children and pets.

In terms of maintenance, the VDDVF36 models are designed for easy access to components, making regular cleaning and servicing straightforward. The durable construction materials used in these fireplaces ensure longevity and reliability, promising years of efficient heating.

Overall, the Vanguard Heating VDDVF36PN/PP and VDDVF36STN/STP models represent the pinnacle of modern gas fireplace technology, combining powerful heating capabilities, stylish aesthetics, and advanced safety features into one outstanding unit. For homeowners seeking a reliable and attractive heating solution, these fireplaces are an excellent choice.