Louisville Tin and Stove BBT54, BBT53, BBT103, BBT104 warranty Vent Weather Seal KIT VWSK5/10

Page 19

VENT WEATHER SEAL KIT - VWSK5/10

NOTE: This kit has been designed and certified for use with a Cozy gas baseboard heater only. Use only factory supplied kit and components. See Figure 1 for parts list of Vent Weather Seal Kit.

STEP 1. Change the location for the vent by following Figure 1 in the installation and operating instructions provided with the Cozy gas baseboard heater.

STEP 2. Drill a three (3) inch diameter hole through the wall of the chosen location.

STEP 3. Measure the wall thickness.

STEP 4. Using a two (2) inch tube cutter, cut the PVC wall sleeve seven-eights (7/8”) inch longer than the measured wall thickness. See Figure 2.

STEP 5. Clean the PVC sleeve and apply PVC cement (provided) on opposite sides of sleeve. Place straps on cement leaving eight (8) inches past sleeve end. Wait ten (10) minutes for cement to dry before proceeding to Step 6. See Figure 2.

STEP 6. Apply petroleum jelly or an equivalent lubricant to the outside of the weather seal. The lubricant will make it easier to push the weather seal through the wall. See Figure 2.

STEP 7. From inside, hold the wall sleeve with the PVC straps lined up horizontally. Push the PVC pipe and weather seal slowly through the wall until the weather seal is completely outside the wall. See Figure 3.

STEP 8. Pull the PVC straps toward you to pull the weather seal firmly against the outside wall. See Figure 3.

STEP 9. Being careful to keep the PVC straps lined up horizontally and pulled tight to maintain the outside seal, bend the straps away from sleeve and secure to wall. Depending on type of wall, anchors (not provided) may be required. See Figure 4.

STEP 10. First, put blue pipe plug in PVC pipe to prevent insulation from getting inside! Insert nozzle from a tube of foam insulation between the wall and the wall sleeve. Starting at the weather seal, slowly inject the foam, working towards the inside wall. CAUTION: Read the manufacturers instructions on the can of foam for special instructions and warnings.

STEP 11. Wait fifteen (15) minutes for foam to dry, cut away any excess from around sleeve on inside wall. If Cozy gas baseboard heater will be installed at a later date, leave the pipe plug in the wall sleeve to seal the vent hole.

STEP 12. Install the Cozy gas baseboard heater per the installation instructions provided with heater.

STEP 13. Slide the O-ring over the air intake tube to a position approximately two (2”) inches from the end of the tube. See Figure 5.

STEP 14. Remove pipe plug from wall sleeve.

STEP 15. Apply petroleum jelly or equivalent lubricant around the outside of the O-ring. Insert the air intake tube through the PVC wall sleeve until back of heater is against the wall. Secure heater to wall.

CONT’D. --- ILLUSTRATIONS - NEXT PAGE

Page 19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Canadian Patent # Direct Vent GAS Baseboard HeaterContents Safety Rules Clearances to Combustibles ClearancesLocation Clearances CONT’DThermostat Location Optional Kits InstallationStep Direct Vent GAS Baseboard ComponentsDo not cut to less than 7-1/2 Cont’d. next Completing Installation Operating Instructions For Your Safety Read Before OperatingTo Turn OFF GAS to Appliance Conversion Instructions GAS ConversionProper Burner Flame To Remove Main Burner for Inspection and CleaningBurner Orifice Wiring Diagram BBT53 & BBT54 WiringWiring Diagram BBT103 & BBT104 Step # Sequence of OperationStep Vent Riser KITSide Valve Concealer KIT SVCK5/10 Bottom Valve Concealer KIT BVCK5/10 Vent Weather Seal KIT VWSK5/10 Vent Weather Seal KIT Cont’d Symptom Possible Causes Corrective Action Trouble Shooting ChartMaintenance Instructions Trouble Shooting Control BoardService Record Date Model Numbers Direct Vent GAS Baseboard HeaterMarch If YOU CAN’T Light IT DON’T Fight IT Your GAS Control and Pilot Light SystemTampering is Dangerous If YOU Smell GAS, DON’T Light ITLouisville TIN and Stove Company Limited Warranty

BBT103, BBT104, BBT54, BBT53 specifications

Louisville Tin and Stove's BBT series, specifically the BBT54, BBT53, BBT103, and BBT104, represents a blend of traditional craftsmanship and modern heating technology. Each model is engineered to provide efficient heating solutions, making them ideal for both residential and commercial applications.

The BBT54 is a compact yet powerful unit, designed to fit seamlessly into smaller spaces while delivering robust heating capabilities. It features advanced insulation technology that maximizes heat retention, ensuring that the warmth permeates the room efficiently. With its user-friendly thermostat, homeowners can easily select their desired temperature settings, making it an excellent choice for energy-conscious consumers.

In contrast, the BBT53 emphasizes versatility and aesthetic appeal. It showcases a sleek design that complements various interior styles, from rustic to contemporary. This model includes a multi-fuel option, allowing users to choose between wood, coal, or gas, providing flexibility depending on the user's preferences and availability of resources. The BBT53 is also equipped with an automated ash removal system, reducing maintenance needs and making it user-friendly.

The BBT103 stands out with its larger heating capacity, suitable for bigger rooms or open floor plans. Its convection heating technology ensures even heat distribution, avoiding hot and cold spots in the room. This model also comes with smart technology features, including remote operation via smartphone apps, making it convenient for users to manage their heating systems from a distance.

Finally, the BBT104 is the flagship model in this series, boasting both power and sophistication. It integrates advanced environmental technologies, such as an eco-mode that optimizes fuel consumption, significantly reducing emissions. The BBT104 is also designed with a premium finish, adding an elegant touch to any space. Moreover, its enhanced safety features include automatic shut-off and carbon monoxide detection, ensuring peace of mind for families and businesses alike.

The Louisville Tin and Stove BBT series exemplifies the brand's commitment to quality and innovation in heating technology. Each model caters to different needs, whether it’s for energy efficiency, versatility, or enhanced safety, making the BBT54, BBT53, BBT103, and BBT104 outstanding choices for those seeking reliable and stylish heating solutions.
Top Page Image Contents