Louisville Tin and Stove BBT54, BBT53, BBT103, BBT104 warranty Safety Rules

Page 3

SAFETY RULES

The Direct Vent Gas Baseboard Heater and its components meet all applicable safety standards when installed as directed in this manual. For safe installation and operation of your Direct Vent Gas Baseboard Heater, read all these instructions before you begin. Failure to follow them exactly will void your warranty and may present a fire hazard.

1.Improper installation, adjustment, alteration, service, or maintenance can cause property damage, bodily injury, or death.

2.Use in other than a residential application may result in unsatisfactory performance and may void the warranty.

3.Follow all applicable codes and ordinances. If there are none, follow the latest edition of National Fuel Gas Code ANSI Z223.1 A copy may be obtained from the CSA International, or the National Fire Protec- tion Association, Batterymarch Park, Quincy, MA. 02269. In Canada, use latest edition of CAN1-B149 installation code.

4.DO NOT INSTALL THIS FURNACE IN A RECREATIONAL VEHICLE.

5.Do not operate baseboard heater unless it is connected to the factory supplied vent system.

6.Check the rating label attached to the baseboard heater to be sure it is equipped for the type gas you intend to use.

7.Never use a match, candle, flame or other source of ignition to check for gas leaks. Use only soapy water or liquid detergent.

8.Have your baseboard heater and vent system inspected at least annually by a qualified service technician.

9.Before cleaning or servicing, turn off the gas and allow heater to cool.

10.Do not operate baseboard heater without all components properly installed.

11.Due to high temperatures, the baseboard heater should be located out of traffic and away from furniture and drapes.

12.Children and adults should be alerted to the hazard of high surface temperature and should be kept away to avoid burns or clothing ignition.

13.Young children should be carefully supervised when they are in the same room with the baseboard heater.

14.Do not place clothing or other flammable material on or near the heater.

15.INSTALLATION AND REPAIR SHOULD BE DONE BY A QUALIFIED SERVICE PERSON. THE BASEBOARD HEATER SHOULD BE INSPECTED BEFORE USE AND AT LEAST ANNU- ALLY BY A PROFESSIONAL SERVICE PERSON. More frequent cleaning may be required

due to excessive lint from carpeting, bedding material, etc. It is imperative that control compartments, burner, and circulating air passageways of the heater be kept clean.

16.Do not install in a closet, alcove, or small hallway where the heater could be isolated from the space to be heated by closing a door.

17.Do not put anything around the heater or vent that will obstruct the flow of combustion and ventilation air. The flow of ventilation air through the upper and lower louvers must not be obstructed.

18.The appliance, when installed, must be electrically grounded in accordance with local codes or, in the absence of local codes, with the latest edition of National Electrical Code, ANSI/NFPA 70. In Canada, use CSA C22.1.

19.Never operate this heater without the burner sight glass in place or with the glass broken or missing.

20.If it is suspected that rising water may enter the heater, turn off the gas immediately.

21.Do not use the heater if any part has been under water. Immediately call a qualified service technician

to inspect the appliance and to replace any part of the control system and any gas control which has been under water.

22.It is necessary to replace damaged gaskets or sealing material within the vent or air intake system. Failure to do so may result in property damage, personal injury, loss of life or unsatisfactory performance.

23.The cabinet cover removed for servicing must be replaced prior to operating heater.

24.This heater must not be connected to a chimney flue.

Page 3

Page 2 Page 4
Image 3
Page 2 Page 4
Contents Canadian Patent # Direct Vent GAS Baseboard HeaterContents Safety Rules Clearances to Combustibles ClearancesClearances CONT’D LocationThermostat Location Installation Optional KitsStep Direct Vent GAS Baseboard ComponentsDo not cut to less than 7-1/2 Cont’d. next Completing Installation For Your Safety Read Before Operating Operating InstructionsTo Turn OFF GAS to Appliance Conversion Instructions GAS ConversionTo Remove Main Burner for Inspection and Cleaning Proper Burner FlameBurner Orifice Wiring Wiring Diagram BBT53 & BBT54Wiring Diagram BBT103 & BBT104 Step # Sequence of OperationStep Vent Riser KITSide Valve Concealer KIT SVCK5/10 Bottom Valve Concealer KIT BVCK5/10 Vent Weather Seal KIT VWSK5/10 Vent Weather Seal KIT Cont’d Symptom Possible Causes Corrective Action Trouble Shooting ChartTrouble Shooting Control Board Maintenance InstructionsService Record Date Model Numbers Direct Vent GAS Baseboard HeaterMarch If YOU CAN’T Light IT DON’T Fight IT Your GAS Control and Pilot Light SystemTampering is Dangerous If YOU Smell GAS, DON’T Light ITLouisville TIN and Stove Company Limited Warranty

BBT103, BBT104, BBT54, BBT53 specifications

Louisville Tin and Stove's BBT series, specifically the BBT54, BBT53, BBT103, and BBT104, represents a blend of traditional craftsmanship and modern heating technology. Each model is engineered to provide efficient heating solutions, making them ideal for both residential and commercial applications.

The BBT54 is a compact yet powerful unit, designed to fit seamlessly into smaller spaces while delivering robust heating capabilities. It features advanced insulation technology that maximizes heat retention, ensuring that the warmth permeates the room efficiently. With its user-friendly thermostat, homeowners can easily select their desired temperature settings, making it an excellent choice for energy-conscious consumers.

In contrast, the BBT53 emphasizes versatility and aesthetic appeal. It showcases a sleek design that complements various interior styles, from rustic to contemporary. This model includes a multi-fuel option, allowing users to choose between wood, coal, or gas, providing flexibility depending on the user's preferences and availability of resources. The BBT53 is also equipped with an automated ash removal system, reducing maintenance needs and making it user-friendly.

The BBT103 stands out with its larger heating capacity, suitable for bigger rooms or open floor plans. Its convection heating technology ensures even heat distribution, avoiding hot and cold spots in the room. This model also comes with smart technology features, including remote operation via smartphone apps, making it convenient for users to manage their heating systems from a distance.

Finally, the BBT104 is the flagship model in this series, boasting both power and sophistication. It integrates advanced environmental technologies, such as an eco-mode that optimizes fuel consumption, significantly reducing emissions. The BBT104 is also designed with a premium finish, adding an elegant touch to any space. Moreover, its enhanced safety features include automatic shut-off and carbon monoxide detection, ensuring peace of mind for families and businesses alike.

The Louisville Tin and Stove BBT series exemplifies the brand's commitment to quality and innovation in heating technology. Each model caters to different needs, whether it’s for energy efficiency, versatility, or enhanced safety, making the BBT54, BBT53, BBT103, and BBT104 outstanding choices for those seeking reliable and stylish heating solutions.
Top Page Image Contents