Enerco 7000ID owner manual Transporting Moving the Heater, Analysis of Combustion Waste Products

Page 6

TRANSPORTING AND

MOVING THE HEATER

To move the Jumbo use the front handles and back wheels.

Warning

Before moving the unit:

•Turn it off as indicated above.

•Disconnect electricity by pulling out the plug.

Suitable equipment must always be used when moving a unit and the instructions given above must be scrupulously adhered to.

Warning

Never try to lift the heater manually. Doing so could result in physical injury.

If heater is connected to propane supply cylinder and it is to be stored indoors, the connection between the propane cylinder and the heater must be disconnected and the cylinder removed from the heater and stored in accordance with Standard for the Storage and Handling of Liquefied Petroleum Gases, ANSI/NFPA 58 and CSA B149.1, Natural gas and Propane Installation Code.

Analysis of Combustion Waste Products

The probes which check the composition of combustion waste products and smoke temperature must be positioned as indicated in Fig. 2. When these tests have been completed the hole which

was drilled for the probe must be sealed with a material which is resistant to high temperatures and which ensures that the tube remains airtight.

8 in

Fig. 2

Connection to Fuel Supply

To connect the burner to the fuel supply follow the instructions in the Burner Instruction Manual.

The gas burner can use both methane gas or propane. Burners are predisposed at factory to be used with natural gas. If propane shall be used, burners shall be adapted according to the instruction manual of the burner. In case of connection of heater to natural gas,the installation shall conform with local codes, or, in

the absence of local code, with the National Fuel Gas Code ANSI Z223.1/NFPA and the Natural Gas and Propane Installation Code,

CSA B149.1.

In case of connection of heater to propane supply cylinder, the installation shall conform with local codes or, in the absence of local code, with tyhe Standard for the Storage and Handling of Liquefied Petroleum Gases, ANSI/FNPA 548 and the Natural Gas and Propane Installation Code, CSA B149.1. Heater must be located at least 6 ft in the U.S. or 10 ft in Canada from

any propane gas container. Propane gas cylinder shall be in compliance with national standards and shall be arranged to provide for vapor withdrawal from the operating cylinder.

The gas shall be turned off at the propane supply cylinder when the heater is not in use. Visually inspect hose assembly prior to each use of the heater. If it is evident there is excessive abrasion or wear, or the hose is cut, it must be replaced prior to the heater

being put into operation. After installation, proper instruments or devices shall be used to check and avoid any gas leakage. Gas leakage testing shall be regularly operated.

Regulation of Combustion - I° Operation

After having checked the hermetic seal and of combustion waste

products line, heater may be operated for the first time.

To perform regulation of combustion correctly, combustion waste products must be analyzed using appropriate instruments: values recommended by actual standards must be reached.

The regulation procedure has been on the Burner Instruction Manual; final values of CO2 shall be correspondent to excess air factor of 1.2 (12.5 for gas-oil, 9.7% for G20. 9.6% for G25. 11.7% for G30 and 11.7% for G31) while CO level shall be less than 75

ppm.

Warning

Never stop the heater by simply turning off the disconnecting switch on the electric switchboard. The electrical supply must only be disconnected when the fan has come to a complete stop.

When the control knob is turned to the symbol the heater operates in continuous fan mode.

ENERCO GROUP, INC. Indirect Fired Portable Heater

6

Operating Instructions and Owner’s Manual

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Indirect Fired General Hazard Warning General Recommendations Installation Instructions for USEMaintenance Connection to Fuel Supply Transporting Moving the HeaterAnalysis of Combustion Waste Products Regulation of Combustion I OperationTroubleshooting Wiring Diagram 4000iD Series Models Wiring Diagram 4000iD and 7000iD Series Models 4000ID and 7000ID Series Indirect-Fired Space Heater 103 101 102 100 4000ID/7000ID Series Indirect-Fired Space Heater Parts List Burner casing SX cover Parts Ordering Information Pièces DE Commande LA SUR Informations Xxxxx Nº 08/08107 9010-G04196 101 102 104 103 100 106 105 107 Page 7000ID ET 4000ID Modèles Électrique Schéma 4000ID Modèle Électrique Schéma Dépannage Santinsuffi RéchauffementAvertissement VentilateurEntretien Dentretien Opération Chaque Après GénérateurCommande de Panneau Fonctionnement DE InstructionsRéglages et électriques Branchements Générales Recommandations HD7000ID 4000IDMatières DES Table Indirecte Combustion À Portable Chaud Dair Générateur

7000ID specifications

The Enerco 7000ID is a cutting-edge infrared heater that represents a significant advancement in portable heating technology. This versatile and efficient heating solution is designed for both residential and commercial applications, providing users with comfort and convenience during colder months.

One of the standout features of the Enerco 7000ID is its innovative infrared technology. Unlike traditional heaters that warm the air, infrared heaters generate radiant heat that warms objects and people directly within their vicinity. This results in feeling warm almost instantaneously, allowing for quick and efficient heating. The infrared heat produced is similar to the heat from the sun, making it a natural and comfortable option for indoor and outdoor spaces.

Another notable characteristic of the Enerco 7000ID is its impressive heating capacity. Designed to heat spaces up to 1,500 square feet, this model is suitable for large rooms, garages, patios, and workshops. Its powerful 7,000 BTU output ensures that even during the coldest days, users can maintain a warm and inviting environment.

The Enerco 7000ID also places a strong emphasis on safety and durability. It is equipped with advanced safety features such as an automatic shut-off system that activates in the case of overheating or tipping. Additionally, the outer casing is designed with high-quality materials that withstand the rigors of frequent use, making it both reliable and long-lasting.

Portability is another key aspect of the Enerco 7000ID. The unit is designed with built-in handle grips, making it easy to move from one location to another. Its compact design means it can be easily stored when not in use, freeing up valuable space in homes or businesses.

Moreover, the Enerco 7000ID operates quietly, contributing to a more pleasant environment without the disruptive noise associated with conventional heaters. Its user-friendly thermostat controls allow for easy temperature adjustments, ensuring users can customize their heating experience to their personal comfort levels.

In summary, the Enerco 7000ID is a powerful, efficient, and versatile infrared heater that excels in both performance and safety. Its advanced heating technology, impressive capacity, portable design, and focus on user comfort make it an ideal choice for anyone seeking an effective heating solution for their space. Whether used indoors or outdoors, the Enerco 7000ID promises to deliver warmth and comfort when it is needed most.
Top Page Image Contents