Motorola BT100 operation manual Bench Testing, Before You Begin, Test Equipment and Connections

Page 40

Section 4

Bench Testing

Motorola’s recommended procedure for placing a new BT100 into service is to fully test it on the bench before it is installed. There are specific alignment procedures that ensure proper functioning of all components and simplify final installation. If the BT100 is properly aligned on the bench, only minor adjustments may be required in the field.

The following subsections provide instructions to bench align the BT100.

Before You Begin

The BT100 is shipped with a 20 ampere blade-type fuse in each active port for over current protection.

CAUTION!

To avoid applying 60/90 Vac to the test equipment during testing, remove the fuse from the connected output port F2, F3, F4 or F5 (illustrated in Figure 2-9). Terminate all unused ports.

Open the housing and remove the electronics chassis cover. Refer to your system drawings or records to confirm the presence of the required options as described in Section 2, “Overview,” Options and Accessories.

Reinstall the electronics chassis cover and torque the screws to 10–12 in-lbs.

Test Equipment and Connections

The equipment typically used for testing the BT100 consists of a network analyzer, such as the HP8712 or 8713 series, a 60/90 VAC bench power supply, a cable simulator, a Motorola model SSP-PIN power combiner, and a variety of jumper cables, adapters, and fittings.

Fabricate a cable simulator that you can configure to provide the desired cable loss in 1 dB increments, up to approximately 30 dB. Then, connect the test equipment as shown in Figure 4-1:

Figure 4-1

Test equipment connections for bench sweeping

BT100 Installation and Operation Manual

Page 39 Page 41
Image 40
Page 39 Page 41
Contents Installation Special Symbols That Might Appear on the Equipment FCC Compliance Contents Bench Testing InstallationSpecifications Torque Specifications Abbreviations and AcronymsFigures TablesIntroduction Illustrates a closed BT100Illustrates an open BT100 Using This Manual Related Documentation Document ConventionsIf You Need Help Technical Response CenterCalling for Repairs Overview Illustrates the various output-port configurations Ordering Guide Identifies and describes the model stringsHousing Overview2-5 Housing Gaskets Illustrates the housing gasketsPower Supply Port LocationsBT100 power supply Forward Path BT100*-4* four output block diagram Return Path Ingress Control Switch Options and Accessories Model Description FunctionJXP-RPC Amplifier Setup Proper Handling ProceduresBench Setup Field PracticeForward Path Alignment Before You BeginStarline Forward Equalizers ExampleStarline Forward Equalizers SFE-100 Starline Cable Simulators SCS Frequency Cable slope in dBInput, Midstage, and Output Pads Information in -2 is shown as a graph in FigureFlatness Control Directional Coupler Test Points Bode EqualizationAmplifier Level Control Temperature Gain ReserveManual Gain Control Thermal Drive Unit Automatic Drive Unit/QAM Automatic Drive Unit Return Path Alignment ADU/QADU Pads and LevelsAlignment Procedure Powering and Surge Protection Before You Begin Bench TestingTest Equipment and Connections Measuring Forward Gain Testing Return Gain and Response ExampleCompleting the Test Procedures Installation Aerial InstallationJumper position Description Torque sequencePedestal Installation Grounding the BT100Using Amplifiers in Lower Gain Systems Using Amplifiers in Lower Frequency SystemsOperating Tips Specifications SpecificationModel BT100 Forward AmplifierParameter Specification AC CurrentRA-Kit/H Return Amplifier ADU/QADU Automatic Drive UnitTorque Specifications Torque Fastener Screw Size Wrench Size In-lbsAbbreviations and Acronyms CTBVisit our website at 527550-001-a

BT100 specifications

Motorola has long been a pioneer in telecommunications, and its BT100 model exemplifies the brand's commitment to innovation and reliability in the realm of Bluetooth technology. The Motorola BT100 is a Bluetooth headset that combines sleek design, advanced features, and robust performance, making it an ideal choice for users seeking hands-free convenience.

One of the standout features of the BT100 is its impressive battery life. With a talk time of up to 10 hours, users can engage in long conversations without the constant need to recharge. Additionally, the standby time stretches up to 200 hours, meaning the headset can remain powered for extended periods when not in use. This makes it a great companion for those who are always on the go.

In terms of design, the Motorola BT100 boasts a lightweight and ergonomic structure that ensures comfort during prolonged use. Its adjustable and flexible ear hook allows for a secure fit, accommodating various ear shapes and sizes. The sleek profile of the headset also makes it visually appealing, allowing it to blend seamlessly with any outfit, whether professional or casual.

The sound quality of the Motorola BT100 is another significant aspect that deserves mention. The headset is equipped with noise-cancellation technology, which minimizes background noise and enhances the clarity of voice calls. This feature is particularly beneficial in busy environments or noisy settings, ensuring that users can communicate effectively without distractions.

Connectivity is seamless with the BT100, which utilizes Bluetooth 5.0 technology, providing a stable connection with a range of up to 33 feet. This allows users to move around freely without being tethered to their devices. The headset is compatible with a wide variety of smartphones, tablets, and laptops, making it a versatile accessory for any tech-savvy individual.

Moreover, the Motorola BT100 is user-friendly, featuring intuitive controls that enable easy management of calls and media playback. The headset supports voice commands, allowing users to keep their hands free while still accessing essential functions.

Overall, the Motorola BT100 combines functionality, style, and cutting-edge technology. Its impressive battery life, comfort-oriented design, exceptional sound quality, and seamless connectivity make it an ideal choice for anyone looking for a reliable Bluetooth headset. Whether for business, leisure, or everyday use, the BT100 stands as a testament to Motorola's expertise in crafting high-quality telecommunications devices.
Top Page Image Contents