Motorola BT100 operation manual Aerial Installation

Page 44

Section 5

Installation

The field installation procedures presented in the following subsections assume that the amplifier was previously tested and bench aligned. Cable power and RF signal must be available on the system. Although it is preferable to have a full complement of channels available for balancing, you can adjust the BT100 adequately with a limited number of channels.

You can install the BT100 housing on a messenger strand (aerial) or on a pedestal. The following subsections provide details on each application.

Aerial Installation

The housing is normally mounted horizontally below the strand, with the electronics chassis removed, to avoid possible damage during installation. Connections are made using standard pin-type connectors with a nominal center-conductor diameter of 0.067 inches. The minimum length of the center-conductor pin is 1.5 inches and the maximum length is 1.65 inches. Longer pins can extend past the center-conductor seizure mechanism and degrade the match. Extremely long pins can result in a short circuit.

Figure 5-1

Center-conductor pin length

1.65" Max.

1.50" Min.

To install the unit:

1Power down the cable before you install the housing. This avoids blown fuses, tripped circuit breakers, and possible personal injury.

2Mount the housing, and torque the two 5/16-inch messenger clamp bolts, located on the long sides of the housing (illustrated in Figures 2-5 and 2-7) to 12 ft-lbs.

3Form the customary expansion loops and make all cable connections according to system design.

4Tighten the center-conductor seizure screw using a Phillips-head screw driver. An alternative method is to use a 3/16-inch socket and a torque wrench. The recommended torque is 12 in-lbs. maximum.

5To avoid water ingress, ensure that aluminum connectors are torqued to the specifications recommended by the connector manufacturer.

6If previously removed, re-install the electronics chassis and fasten it to the housing with the six captive bolts. Torque to 18 to 22 in-lbs.

7Remove the input pad (JXP IN) to avoid damage to the hybrids.

BT100 Installation and Operation Manual

Page 43 Page 45
Image 44
Page 43 Page 45
Contents Installation Special Symbols That Might Appear on the Equipment FCC Compliance Contents Bench Testing InstallationSpecifications Torque Specifications Abbreviations and AcronymsFigures TablesIntroduction Illustrates a closed BT100Illustrates an open BT100 Using This Manual Related Documentation Document ConventionsIf You Need Help Technical Response CenterCalling for Repairs Overview Illustrates the various output-port configurations Ordering Guide Identifies and describes the model stringsHousing Overview2-5 Housing Gaskets Illustrates the housing gasketsPower Supply Port LocationsBT100 power supply Forward Path BT100*-4* four output block diagram Return Path Ingress Control Switch Options and Accessories Model Description FunctionJXP-RPC Amplifier Setup Proper Handling ProceduresBench Setup Field PracticeForward Path Alignment Before You BeginStarline Forward Equalizers ExampleStarline Forward Equalizers SFE-100 Starline Cable Simulators SCS Frequency Cable slope in dBInput, Midstage, and Output Pads Information in -2 is shown as a graph in FigureFlatness Control Directional Coupler Test Points Bode EqualizationManual Gain Control Temperature Gain ReserveAmplifier Level Control Thermal Drive Unit Automatic Drive Unit/QAM Automatic Drive Unit Return Path Alignment ADU/QADU Pads and LevelsAlignment Procedure Powering and Surge Protection Test Equipment and Connections Bench TestingBefore You Begin Measuring Forward Gain Testing Return Gain and Response ExampleCompleting the Test Procedures Installation Aerial InstallationJumper position Description Torque sequencePedestal Installation Grounding the BT100Operating Tips Using Amplifiers in Lower Frequency SystemsUsing Amplifiers in Lower Gain Systems Specifications SpecificationModel BT100 Forward AmplifierParameter Specification AC CurrentRA-Kit/H Return Amplifier ADU/QADU Automatic Drive UnitTorque Specifications Torque Fastener Screw Size Wrench Size In-lbsAbbreviations and Acronyms CTBVisit our website at 527550-001-a

BT100 specifications

Motorola has long been a pioneer in telecommunications, and its BT100 model exemplifies the brand's commitment to innovation and reliability in the realm of Bluetooth technology. The Motorola BT100 is a Bluetooth headset that combines sleek design, advanced features, and robust performance, making it an ideal choice for users seeking hands-free convenience.

One of the standout features of the BT100 is its impressive battery life. With a talk time of up to 10 hours, users can engage in long conversations without the constant need to recharge. Additionally, the standby time stretches up to 200 hours, meaning the headset can remain powered for extended periods when not in use. This makes it a great companion for those who are always on the go.

In terms of design, the Motorola BT100 boasts a lightweight and ergonomic structure that ensures comfort during prolonged use. Its adjustable and flexible ear hook allows for a secure fit, accommodating various ear shapes and sizes. The sleek profile of the headset also makes it visually appealing, allowing it to blend seamlessly with any outfit, whether professional or casual.

The sound quality of the Motorola BT100 is another significant aspect that deserves mention. The headset is equipped with noise-cancellation technology, which minimizes background noise and enhances the clarity of voice calls. This feature is particularly beneficial in busy environments or noisy settings, ensuring that users can communicate effectively without distractions.

Connectivity is seamless with the BT100, which utilizes Bluetooth 5.0 technology, providing a stable connection with a range of up to 33 feet. This allows users to move around freely without being tethered to their devices. The headset is compatible with a wide variety of smartphones, tablets, and laptops, making it a versatile accessory for any tech-savvy individual.

Moreover, the Motorola BT100 is user-friendly, featuring intuitive controls that enable easy management of calls and media playback. The headset supports voice commands, allowing users to keep their hands free while still accessing essential functions.

Overall, the Motorola BT100 combines functionality, style, and cutting-edge technology. Its impressive battery life, comfort-oriented design, exceptional sound quality, and seamless connectivity make it an ideal choice for anyone looking for a reliable Bluetooth headset. Whether for business, leisure, or everyday use, the BT100 stands as a testament to Motorola's expertise in crafting high-quality telecommunications devices.
Top Page Image Contents