Lennox International Inc G50UH-48B-090, G50UH-48C-110, G50UH-60D-135 Primary and Secondary Limits

Page 27

ralgasatallaltitudesis3.5"w.c.Manifoldpressurefor allunitsfueledbyL.R/propanegasat allaltitudesis 10.0"w,c.Seefigures27,28and29forthelocationof themanifoldpressureadjustmentscrews,

NOTE - In Canada, certification for installations at eleva-

tions over 4500 feet (1372 m) is the jurisdiction of local au- thorities.

Manifold pressure for all units fueled by natural gas at all altitudes is 3.5" w,c, Manifold pressure for all units fueled by L,R/propane gas at all altitudes is 10,0" w,c,

NOTE - A natural to L.R propane gas changeover kit is nec- essary to convert this un#. L.R conversion kit 25W20 is used with all units installed at altitudes up to 7,500 feet. L.P. conversion kit 25W21 is used with all units installed at alti- tudes from 7,501 to 10,000 feet above sea level. Refer to the changeover kit installation instruction for the conver- sion procedure.

NOTE - Units fueled by natural gas and installed at alti- tudes of 7501-10,000 feet above sea level require instal- lation of a high altitude orifice kit (59M17).

The combustion air pressure switches are factory-set and require no adjustment, The existing unit pressure switch must be replaced by pressure switch 56L32 for G50UH(X) units installed at altitudes from 7,501 to 10,000 feet above sea level,

Primary and Secondary Limits

The primary limit is located on the heating compartment vestibule panel. The secondary limits (if equipped) are lo- cated in the blower compartment, attached to the back side of the blower. These limits are factory set and require no adjustment.

Flame Rollout Switches (Two)

These manually reset switches are located on (or inside of) the burner box, If tripped, check for adequate combustion air before resetting,

Pressure Switch

The pressure switch is located in the heating compartment adjacent to the combustion air inducer. This switch checks for proper combustion air inducer operation before allow- ing ignition trial, The switch is factory-set and requires no adjustment.

Temperature Rise

Place the unit into operation with a heating demand, After supply and return air temperatures have stabilized, check the temperature rise, If necessary, adjust the blower speed to maintain the temperature rise within the range shown on

the unit nameplate, Increase the blower speed to decrease the temperature, Decrease the blower speed to increase the temperature rise, Failure to do adjust the temperature rise may cause erratic limit operation,

Fan Control

Heating Mode -- The fan on delay of 45 seconds is not ad- justable. The fan offdelay (amount of time that the blower operates after the heat demand has been satisfied) may be adjusted by setting $1 switches 1and 2 located on the SureLight ® control. The unit is shipped with a factory fan off setting of 90 seconds, The fan off delay affects com- fort and is adjustable to satisfy individual applications.

Adjust the fan off delay to achieve a supply air tempera- ture between 90 °and 110°F at the exact moment that the

blower is de-energized. Longer offdelay settings provide lower return air temperatures; shorter settings provide higher return air temperatures. See figure 25.

Cooling Mode --The cooling mode fan off delay (amount of time that the blower operates after the cooling demand has been satisfied) may be adjusted by setting $1 switch 3 located on the SureLight ® control, In the off position, the cooling fan off delay is 2 seconds. In the on position, the cooling fan off delay is 45 seconds, See figure 25,

Thermostat Heat Anticipation

Set the heat anticipator setting (if adjustable) according to the amp draw listed on the wiring diagram that is attached to the unit.

Electrical

1 - Check all wiring for loose connections,

2 - Check for the correct voltage at the furnace (furnace operating).

3 - Check amp-draw on the blower motor.

Motor NameplateActual

NOTE - Do not secure the electrical conduit directly to the air ducts or structure.

Blower Speeds

NOTE - CFM readings are taken external to unit with a dry evaporator coil and without accessories.

1 - Turn off electrical power to furnace,

2 - Remove blower access panel.

3 - Disconnect existing speed tap at control board speed terminal.

NOTE - Termination of any unused motor leads must be insulated.

4 - Refer to blower speed selection chart on unit wiring dia- gram for desired heating or cooling speed.

5- Connect selected speed tap at control board speed terminal.

6 - Resecure blower access panel.

7 - Turn on electrical power to furnace, Electronic Ignition

The SureLight @integrated control has an added feature of an internal Watchguard control, The feature serves as an automatic reset device for ignition control lockout caused by ignition failure, After one hour of continuous thermostat demand for heat, the Watchguard will break and remake thermostat demand to the furnace and automatically reset the control to begin the ignition sequence,

Page 27

Page 26 Page 28
Image 27
Page 26 Page 28
Contents G50UHX Series Supply AIR FlueBoxGasket HeatExchanger FlueCollectorBox Gasket FlueTransitionPackage 1 of 1 contains Wheninstalled,thisfurnacemustbeelectricallygrounded Acaution Canada,referto the standardCSAB149installation codesAir from Inside WiTER/ RoomEquipment in Confined Space ALL AIR from Outside Mm at unit front. The unit must be levelSide View Front View 27-5/8Leveling an Upflow Unit Leveling Bolt Installation Inches mmRemovingthe Bottom Panel Removing the Bottom PanelHorizontal Application Unit Installed on Platform Hole Filter SizeSupply Air Plenum Combustion Air InducerVent Connection Venting Using a Masonry ChimneyOutletopeningSeefigure15 Thelatesteditionof NationalFuelGasCodeNFPA54Minimum Vent capacity Common Venting Using Tile-Lined Interior Masonry ChimneCombined Vent Connector Single applianceMaximum Horizontal Inches mm MIN MAX Serving a Single Category I Appliance Serving Two or More Category I Appliances Type B Double-WallVents with Type B Double-Wall ConnectorsRemoval of the Furnace from Common Vent VentGas Pipe Capacity ft3/hr m3/hr PropaneInstallationCodesinCanadaElectrostatic Discharge ESD Precautions and ProceduresInterior MAKE-UP BOX Installation Leak CheckINTERIORMAKE-UP BOX Installation PowER @1HsuN,TZk for Correct Number of Secondary Typical G50UHX Field Wiring DiagramSot G5OUHXManifold For Your Safety Read Before LightingRevolution Honeywell VR8205 Gas Valve with ON/OFF SwitchPrimary and Secondary Limits FlueAnd Chimney CheckunitforproperdraftG50UHX Burner & Heat Exchanger Removal Ak Caution Diagnostic Surelight Control Normal Heating Mode Abnormal Heating ModeYESl =-lYESl Normalcooling Mode Abnormalcooling ModeYEs FurnaceBtuInput BlowerMotorAmps

G50UH-60D-155, G50UH-36B-090, G50UH-36A-070, G50UH-24A-045, G50UH-60D-135 specifications

Lennox International Inc is renowned for its high-quality heating, ventilation, and air conditioning (HVAC) solutions. Among its versatile product lineup are the G50UH series of gas furnaces, which exemplify efficiency and performance. These models, specifically the G50UH-24A-070, G50UH-24A-045, G50UH-36B-090, G50UH-36A-070, and G50UH-48C-135, offer a range of features tailored to meet varying residential heating demands.

One of the key features of the G50UH series is its energy efficiency. Many models in this lineup boast an impressive Annual Fuel Utilization Efficiency (AFUE) rating, which indicates their ability to convert fuel into usable heat efficiently. These high AFUE ratings can lead to significant savings on energy bills, making these furnaces a cost-effective choice for homeowners.

The G50UH series incorporates advanced technology, including multi-speed blowers that enhance comfort levels. This feature allows for better airflow control and can help maintain consistent temperatures throughout the home. The controlled airflow reduces temperature swings and ensures that every room benefits from the heating provided by the furnace.

Safety is paramount in Lennox designs, and the G50UH series is no exception. Each unit is equipped with safety features designed to protect both the furnace and the home. Dual certification ensures that the products meet stringent safety standards. Moreover, features like a self-diagnostic control board streamline maintenance, allowing homeowners to easily identify potential issues.

Another important characteristic of the G50UH series is its compact design, which is beneficial for homes with limited space. The units are designed to fit comfortably in various installation environments, from basements to utility rooms.

Durability is another hallmark of the G50UH furnaces. Constructed with quality materials, these units are designed for long-term reliability. This ensures that homeowners can enjoy the comfort of their heating systems without frequent repairs.

Lastly, Lennox provides extensive support and warranties, giving homeowners peace of mind associated with their purchase. With options tailored to meet diverse home heating needs, the Lennox G50UH series stands out in the HVAC market, combining efficiency, safety, and reliability in one impressive package.
Top Page Image Contents