Accessibility Clearances Minimum

PRODUCT DESIGN

Accessibility Clearances (Minimum)

Unobstructed front clearance of 24" for servicing is rec- ommended.

MINIMUM CLEARANCE TO COMBUSTIBLE MATERIALS - INCHES

Sides	Rear	Front*		Vent		Top
Sides	Rear	Front*	SW		B	Top
			SW		B
1	0	3	6		1	1

*24" clearance for serviceability recommended.

**Single Wall Vent (SW) to be used only as a conncetor.

Refer to the venting tables outlined in the Installation Manual for additional venting requirements.

Note: In all cases accessibility clearance shall take prece- dence over clearances from the enclosure where accessi- bility clearances are greater. All dimensions are given in inches.

High Altitude Derate

When this furnace is installed at high altitude, the appropri- ate High Altitude orifice kit must be installed. This is re- quired due to the natural reduction in the density of both the gas fuel and combustion air as altitude increases. The kit will provide the proper design certified input rate within the specified altitude range.

INPUT PER BURNER - 22,500 BTUH NATURAL GAS / 20,000 BTUH L.P.

			ELEVATION ABOVE SEA-LEVEL (FEET)
	2000	3000		4000	4500	5000	6000	7000	8000
US BURNER	44/55	44/55		45/56		45/56	46/57	47/58	47/58
ORIFICE	44/55	44/55		45/56		45/56	46/57	47/58	47/58
ORIFICE
CANADA BURNER	44/55				47/57
ORIFICE	44/55				47/57
ORIFICE

HA-02 HIGH ALTITUDE CONVERSION KIT REQUIRED

Tabled data is based upon the furnace input being reduced for altitudes above sea level. U.S. 4% per 1,000 feet. Canada 10% derate for 2,000-4,000 feet.

High altitude kits are purchased according to the installa- tion altitude and usage of either natural or propane gas. Refer to the chart above for a tabular listing of appropriate altitude ranges and corresponding manufacturer’s high altitude Natu- ral Gas and Propane Gas kits. For a tabular listing of appro- priate altitude ranges and corresponding manufacturer's High Altitude Pressure Switch kits, refer to either the Pressure Switch Trip Points & Usage Chart in this manual or the Ac- cessory Charts in Service Instructions.

AMH* specifications

The Amana AMH* series is a line of advanced air conditioning and heating systems designed to provide efficient climate control for residential spaces. Renowned for their innovative features and technology, these systems prioritize comfort, sustainability, and ease of use.

One of the standout features of the Amana AMH* series is its impressive energy efficiency. The units are equipped with high SEER (Seasonal Energy Efficiency Ratio) ratings, which indicate their ability to provide effective cooling while consuming less energy. This not only helps homeowners save on utility bills but also reduces their environmental impact, making the AMH* series an eco-friendly choice for climate control.

The Amana AMH* series incorporates state-of-the-art inverter technology. This technology allows the system to adjust its cooling or heating output based on the specific demands of the home at any given moment. Instead of operating at a single, fixed speed, the inverter-driven compressor can modulate its output, providing a more consistent temperature and improving overall comfort.

Additionally, these systems feature advanced refrigerant technology. They often utilize R-410A refrigerant, which is known for being more environmentally friendly compared to older refrigerants. This contributes to the overall efficiency of the units while minimizing harmful emissions, complying with modern environmental regulations.

Another notable characteristic of the Amana AMH* series is its noise level. Designed with sound insulation and advanced engineering, these units operate quietly, ensuring that the comfort of the indoor environment is not disrupted by excessive noise. This is particularly beneficial in residential settings where quiet operation is essential.

The user-friendly controls of the Amana AMH* systems make them easy to operate. Many units come with smart technology that allows homeowners to control their HVAC system remotely via smartphones or tablets. This feature not only enhances convenience but also allows for better management of energy consumption, further promoting efficiency.

Moreover, Amana products are known for their durability and reliability. Backed by a robust warranty, these systems are built with high-quality materials and components, ensuring they can withstand the test of time and varying weather conditions.

In conclusion, the Amana AMH* series represents a blend of energy efficiency, innovative technology, and user-friendly features, making it an excellent choice for homeowners seeking reliable and effective climate control solutions. With a focus on sustainability, comfort, and quiet operation, the AMH* series stands out as a leader in the HVAC market.