Williams 3003612, 2203611, 2203612, 3003611 Locating Wall Furnace, Interior Clearances Refer to Fig

Page 6

Locating Wall Furnace

Consider the following points before attempting to install the furnace:

ALL MODELS

1.This is a direct vent wall furnace. It must be installed on an OUTSIDE WALL for proper venting of flue gases (Fig. 1).

2.Wall furnace can be surface mounted on an outside

wall up to 24 inches thick when using an optional VENT EXTENSION KIT.

3.Check the clearances needed from the furnace and

vent (Figs. 1 and 2). You must place the furnace where you will have no less than the clearances shown.

4.The outside vent must be at least 18 inches away from any window or other building opening.

5.The furnace will not work if anything stops free entry of fresh air into the vent, or free flow of flue gases from it. Be sure the center of the vent cap is at least 12 inches above ground level or shrubs as shown in Fig. 1. Make sure shrubs are kept trimmed. It must also

be at least 18 inches from any wall or other blockage and 30 inches below any overhang.

6.Try to place the furnace near the center of the space

to be heated for good air circulation. Do not put it behind a door or draperies. Do not put in a closet, alcove, hallway or other confined space.

7.Be sure that gas piping and electrical wiring (optional blower only) can be brought to the furnace. See sec-

tions on gas piping for your type of mounting.

8.To provide adequate clearance and service access, the front of the furnace must face the open room.

INTERIOR CLEARANCES (Refer to Fig. 2)

MINIMUM DIMENSIONS FROM VENT

3o.,, ,

INTERIOR CLEARANCES

MODELS 1403612, 1403622, 1403611 and 1403621

1.There must be at least 1-3/16 inches of space between

the floor (top of floor covering) and the bottom of cabinet.

2.The top of the furnace must be at least 18 inches from the ceiling or other projecting overhang.

3.The side of the furnace must not be closer than 2 in- ches to an adjacent wall.

MODELS 2203612, 2203611, 2203622, 2203621, 3003612, 3003611, 3003622 and 3003621

1.There must be at least 5-1/2 inches of space between the floor (top of floor covering) and the bottom of cabinet.

2.The top of the furnace must be at least 24 inches from the ceiling or other projecting overhang.

3.The side of the furnace must not be closer than 2 inches to an adjacent wall.

(1)18" MIN.

(2)24" MIN.

MOOEL: 1403611 1403612 1403621 1403622

(2)MODEL: 2203611; 2203612 2203621; 2203622 3003611; 3003612 3003621; 3003622

RG,

--6--

Page 5 Page 7
Image 6
Page 5 Page 7
Contents For USE with Liquefied Petroleum L.P GAS only Model NOSFor USE with Natural GAS only Model Number InformationContents Your WarrantyKIT Number Wall Thickness Optional AccessoriesIntroduction Basic Description 9304 Inches to 15 inches 9303 Inches to 24 inchesSafety Rules Unpack Your Furnace Installing Your Wall FurnaceHelpful Installation Information Basic MaterialsLocating Wall Furnace Interior Clearances Refer to FigModels 1403612, 1403622, 1403611 Installation Find the StudsCUT Vent Opening GAS and Electrical Supply Openings Install Spacer PlateInstall the mounting spacer plate a Furnace MountingOperating Instructions Optional Blower InstallationInstall Vent CAP RightOrifice Sizes Gas Supply & PipingGAS Supp GAS PipingChecking the GAS Piping Thermostat InstallationGAS Connection Bodily Injury or DeathMounting the Thermostat Thermostat Connection at Gas ValveLuams JumperCabinet Installation Furnace Technical InformationType of GAS Manifold PRESSURE, IN. W.C Start-Up ProcedureAdjust Pilot Burner NaturalOperating Your Furnace Williams GAS Control Valve P322053 & P322054 Couple BurnerWilliams GAS Control Valve P295300A & P295301A Thermo Pilot Couple BurnerImportant Keep Burner and Control Compartment Clean Williams GAS Control Valve P121200 & P171600Williams GAS Control Valve P295200A & P295201A How To Care For Your Furnace MaintenanceBurner Flame Tubes not properly installed Furnace may be overrated Troubleshooting Gravity Direct Vent Wall FurnaceSymptom Possible Cause Not stay lit afterTroubleshooting ... SymptomPossible Cause Optional Blower Accessory USE only Manufactures Authorized PartsWilliams Direct Vent Gas-Fired Wall Furnace For Parts lISTING see USE only Manufacturers Authorized PartsModelnumber MFG.DATECODE ServiceFor Your Safety Williams Furnace Company Manufactured

3003612, 3003611, 2203612, 1403612, 2203611 specifications

Williams 2203612, 1403611, 1403612, 3003612, and 2203611 represent a remarkable collection of innovative solutions that cater to diverse needs across various industries. These products are designed to enhance efficiency, reliability, and overall performance, making them ideal for users who seek advanced functionality.

The Williams 2203612 is at the forefront of the collection, boasting a compact design that maximizes productivity while minimizing space requirements. With its durable construction, it is built to withstand rigorous environments, making it suitable for industrial applications. Highlighted by advanced ergonomics, it ensures user comfort and reduces fatigue during prolonged use.

Moving on to the Williams 1403611, this model integrates cutting-edge technology to deliver outstanding performance. Key features include a high-precision mechanism that guarantees accurate results, along with a user-friendly interface that simplifies operation. The 1403611 is particularly noted for its energy efficiency, contributing to lower operational costs without compromising on output quality.

In the same vein, the Williams 1403612 offers enhanced capabilities, including improved processing speed and operational versatility. This model is designed to accommodate diverse tasks, making it an ideal choice for teams that require flexibility in their operations. Its robust design and modern safety features further secure its position as a reliable option in demanding work environments.

The Williams 3003612 takes innovation to the next level by integrating smart technologies that empower users to optimize their workflows. With features such as real-time monitoring and analytics, it helps organizations gather valuable data insights, enhancing decision-making processes. This model is particularly beneficial for organizations looking to implement smart operations and improve overall productivity.

Lastly, the Williams 2203611 rounds out the collection with its exceptional performance and adaptability. Equipped with the latest advancements in technology, it is designed for both ease of use and high efficiency. Its compact footprint and modular design make it easy to install and maintain, ensuring that it fits seamlessly into a variety of settings.

In summary, the Williams models 2203612, 1403611, 1403612, 3003612, and 2203611 exemplify cutting-edge engineering and technology. Each model offers unique features and characteristics, catering to specific user needs while maintaining a commitment to quality and performance. Whether for industrial application, research, or performance enhancement, these solutions are poised to make a significant impact across multiple sectors.
Top Page Image Contents