Lennox Hearth CR-3835R Offset Calculations, Return Elbow Max Stabilizer 10 Max Offset

Page 12

12

The offset and return elbows may be attached together, or a section or sections of chimney may be used between, but do not exceed 20' in total length between elbows. If sections of pipe exceed 10' between elbows, a chimney stabi- lizer must be used at the midpoint (Figure 34 ). The stabilizer support straps must be attached under tension (in shear) to structural framing members above. When two sets of elbows are used, the maximum combined length of chim- ney used between elbows cannot exceed 20' (Figure 35 ). Example: If C1 = 10' then C2 cannot exceed 10'.

If an offset exceeds 6' in length, each chimney joint beyond the first 6' of offset to the return elbow, must be secured by a No. 8 x ¹⁄₂" sheet metal screw located at the underside of the joint (Figure 36 ).

A ¹⁄₈" diameter hole must be drilled in the chimney joint using a ¹⁄₈" diameter drill. Hole should be drilled in center of joint overlap (Figure 37 ). Be sure to drill only through the outer chimney casting. Do not puncture the inner flue.

Maximum offset of chimney system is 30° . Two offsets must not be assembled to form a 60° offset. However, two sets of offset and return elbows may be used on a single flue system, provided the total height of the sys- tem exceeds 25'.

Return elbow support straps must be se- curely attached under tension (in shear) to structural framing members above. Do not substitute a FTF8/10-30 offset elbow in place of a FTF8/10-E30 return elbow.

OFFSET CALCULATIONS

Step 1. Use Offset Chart to determine amount of horizontal offset (A) and height (B) for vari- ous chimney section assemblies.

Step 2. Use “Height of Chimney Only” column in The Vertical Elevation Chart to determine combinations of chimney used above return elbow to achieve desired heights. Reference Components Effective Height Chart in vertical elevation chart section.

Step 3. Use Elevation Chart as job estimator only. Add necessary firestop spacers and stabi- lizers as required. Firestop spacers must be used as shown in Figures 21 and 22 and stabi- lizers as shown in Figure 26.

A1

Return

Elbow

20'

Max.

B1

Stabilizer

10' Max.

Offset

Elbow

Figure 34

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

A2

C2

A1

C1

Figure 35

A2

C2

A1

C1

B2

B1

B2

B1

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Retain These Instructions For Future Reference Wood Burning Fireplaces 850,048M REV. N/C 01/2007OTL Report No -F-20-4 Table of Contents Typical Installation IntroductionGeneral Information Chimney Clearances and Mantel Height RequirementsAssembly Outline Chimney HeightChase Enclosure Before You StartAssembly Steps PRE-INSTALLATION NotesInstalling the Fireplace Fireplace ClearancesFireplace Specifications Consult all local codesFraming Specifications Installing the Chimney System 8d Nail Or EquivalentRoom Above Firestop Spacer Attic Above Or Ceiling 51mm** See **Note Min. Air Space to CombustiblesStabilizer Using a CTD Round Termination Using a FTF8/10-CTDT Chase TerminationRoof Pitch Flat to 6/12TEN Foot Rule Summary Multiple TerminationsFTF8 and FTF10 Chimney Component Calculations Special Offset InstructionsOffset Calculations Return Elbow Max Stabilizer 10 Max OffsetFTF8 Vertical Elevation Chart Number Of FTF8Inches Inches Feet/Inches MetersFTF10 Vertical Elevation Chart Number Of FTF10Chimney Only Chimney OnlyFTF8 Offset Elevation Chart With FTF8-SS Starter Section FTF8-S4Inches FTF10 Offset Elevation Chart JointsSection FTF10-ES30 Number of FTF10Installing Offsets Offset Elbow AssemblyReturn Elbow Assembly Combustion Air KitsGlass Doors Cold Climate InsulationFireplace Finishes Mantels and TrimHearth Extension Dimensions 20 508 mm 38 965 mm 203 mm12 305 mm Methods of Determining Hearth Extension and Wall ShieldFinish to Your Taste Value = 1/k = r x thickness of material usedRM = rM x TS = 0.05 x 3/4 = ModelInstallation Components Chase Termination 63L51 Square 63L52Cold Climate Kit 63L63 63L29Page 850,048M REV. N/C 01/2007 Orange, CA

CR-3835R specifications

The Lennox Hearth CR-3835R is a contemporary gas fireplace that exemplifies modern design and advanced technology, creating an ideal centerpiece for any stylish living space. This model seamlessly combines aesthetic appeal with functional efficiency, making it a sought-after choice for homeowners looking to enhance their interiors.

One of the standout features of the CR-3835R is its impressive heat output. With a heating capacity of up to 35,000 BTUs, this fireplace effectively warms up areas ranging from 1,000 to 1,500 square feet, ensuring comfort during chilly months. The adjustable flame height allows users to customize the ambiance according to their preferences, providing a cozy atmosphere or a striking visual display.

The CR-3835R boasts an advanced design that incorporates a sealed firebox. This feature not only improves energy efficiency but also ensures that outdoor air doesn't compromise indoor air quality. The fireplace utilizes an electronic ignition system, which enhances convenience and reliability. With the ability to operate even during power failures, the CR-3835R is a dependable addition to any home.

Another notable characteristic of the Lennox Hearth CR-3835R is its use of high-quality materials. The fireplace is constructed with durable steel and features a refined glass front, allowing an unobstructed view of the flames. The elegant design is complemented by customizable finishing options, enabling users to select styles that align with their interior decor.

In terms of safety, the CR-3835R includes features such as a built-in safety shut-off valve, providing peace of mind for homeowners. The fireplace is also certified for use in a variety of settings, including conventional and direct vent applications. This versatility makes it suitable for a range of installation options.

Moreover, the Lennox Hearth CR-3835R is designed with user-friendly controls, including remote operation capabilities. This function allows for effortless adjustment of settings from the comfort of one's seat, adding an extra layer of convenience to the overall experience.

In summary, the Lennox Hearth CR-3835R combines stylish design, high efficiency, and advanced technology. Its impressive heat output, customizable features, and user-friendly operation make it an excellent choice for those seeking a modern gas fireplace that enhances both comfort and aesthetics in their home. With the CR-3835R, homeowners can enjoy the warmth and ambiance of a traditional fireplace, redefined for contemporary living.
Top Page Image Contents