Lennox Hearth LSM40ST-P, LSM40ST-N Inputs and Efficiencies, Burn-in Period, Deration

Page 7

LENNOX HEARTH PRODUCTS • MONTEBELLO® SEE-THROUGH DIRECT-VENT GAS FIREPLACES (LSM40ST-N / LSM40ST-P) • CARE AND OPERATION INSTRUCTIONS

GENERAL INFORMATION

The fireplace models covered in this manual are direct-vent, sealed combustion, gas fire- places designed for residential application. Direct-vent appliances operate with the com- bustion chamber completely isolated from the indoor environment.

All air for combustion is brought in from the outside, and exhaust gases are vented through the same direct-vent, coaxial (intake/exhaust) vent system.

These appliances are designed to operate on natural or propane gas. The system is switch- able between standing and intermittent pilot modes. External electrical power is required to operate these units. If the system operates on line voltage, four (4) "AA" batteries (in receiver) can be used as a backup in case of a power outage.

These models come standard with a remotely modulated gas valve. The included transmitter remotely controls flame appearance and heat output (manual gas valve adjustment is not possible).

These appliances comply with National Safety Standards and are tested and listed by Intertek (Report No. 100326523PRT-001) to ANSI Z21.88 (in Canada, CSA-2.33), and CAN/CGA- 2.17-M91 (CSA P4.1) in both USA and Canada, as vented gas fireplace.

The installation must conform to local codes or, in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1/NFPA 54 - latest edition, or the Natural Gas and Propane Installa- tion Code, CAN/CSA-B149.1 - latest edition. The appliance, when installed, must be electrically grounded in accordance with local codes or, in the absence of local codes, with the National Electrical Code, ANSI/NFPA 70 - latest edition, or the Canadian Electrical Code, CSA C22.1 - latest edition.

Inputs and Efficiencies

Appliance BTU inputs are listed in Table 1A. Appliance efficiencies are listed in Table 1B.

Inputs

Gas Type (Fireplace Model)

Inputs (BTU/hr)

Natural Gas (LSM40ST-N)

40,000 to 60,000

Liquid Propane (LSM40ST-P)

43,500 to 56,000

Table 1A

EFFICIENCIES

Gas Type (Fireplace Model)

AFUE

EnerGuide

Natural Gas (LSM40ST-N)

68%

67%

Liquid Propane (LSM40ST-P)

70%

67%

Table 1B

Gas Fireplace Energy Ef￿ciency Rating

Based on CSA P.4.1-02

Gas Pressure Requirements (All Models)

Tables 2 and 3 show the appliances’ gas pres- sure requirements.

Inlet Gas Supply Pressure (all models)

Fuel #

Minimum

Maximum

Natural Gas

5.0" WC

10.5" WC

(1.24 kPa)

(2.61 kPa)

 

 

 

 

Propane

11.0" WC

13.0" WC

(2.74 kPa)

(3.23 kPa)

 

 

 

 

Table 2

Manifold Gas Supply Pressure (all models)

Fuel #

Low

High

 

 

 

Natural

(Lo) 1.6" WC

(Hi) 3.5" WC

Gas

(0.4 kPa)

(0.87 kPa)

 

 

 

Propane

(Lo) 6.3" WC

(Hi) 10.0" WC

(1.57 kPa)

(2.49 kPa)

 

 

 

 

Table 3

Test gauge connections are provided on the front of the gas control valve, identified IN for the inlet and OUT for the manifold side (see Figure 1 on Page 8 ). The control valve has a 3/8" (10 mm) NPT thread inlet and outlet side of the valve.

These appliances must be isolated from the gas supply piping system (by closing their individual manual shut-off valve) during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 psig (3.5 kPa).

These appliances and their individual shut-off valves must be disconnected from the gas supply piping system dur- ing any pressure testing of that system at pressures greater than 1/2 psig (3.5 kPa).

Orifice Sizes:

Sea Level to High Altitude (All Models)

These appliances are tested and approved for installations at elevations of 0–4500 feet (0–1372 meters) above sea level using the standard burner orifice sizes (marked with an asterisk

[*]in Table 4).

At the time of installation, it must be determined if the appliance needs to be derated. Contact your local gas supplier for deration requirements for your area.

Burner Orifice Sizes

Elevation 0–4500 feet (0–1372 meters)

Fireplace LSM40ST-N:

Fireplace LSM40ST-P:

Natural Gas

 

Propane

Drill Size (inches)

Drill Size (inches)

 

 

#32 (0.116")*

#52 (0.0635")*

[Orifice Cat. No. H8002]

[Orifice Cat. No. H8003]

 

 

 

Table 4

*Standard size installed at factory.

Deration

At higher elevations, the amount of BTU fuel value delivered must be reduced by either using gas that has been derated by the gas company or by changing the burner orifice to a smaller size as regulated by the local authorities having jurisdiction and by the (USA) National Fuel Gas Code NFPA 54/ANSI Z223.1 - latest edition or, in Canada, the CAN/CSA-B149.1 codes - latest edition.

Burn-in Period

During the first few fires of this appliance there will be some odor due to the curing of the paint and burning off of lubricants used in the manufacturing process. Depending on your use, the burn-in period may take a few hours or a few days.

KEEP YOUR HOUSE WELL VENTILATED DURING THE CURING PROCESS. THE ODOR AND HAZE EMITTED DURING THE CURING PROCESS CAN BE QUITE NOTICEABLE AND MAY SET OFF A SMOKE DETECTOR.

NOTICE:

A white film may develop on the glass enclosure panel during the first few fires as part of the burn-in process.

The first few times you use the fireplace, clean the glass after each use (AFTER THE GLASS HAS COMPLETELY COOLED); otherwise, the white film will bake onto the glass and become difficult to remove.

See glass cleaning instructions on

Page 9.

7

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Image 7
Contents 506025-05 Rev. C 05/2011 Important Safety InformationSafety Your Fireplace Spanish Seguridad y su chimenea Et toute commande qui a été plongée dans l’eau Important Safety InformationColocación de advertencias de seguridad en operación Attaching Safety-in-Operation WarningsLennox Warranty Information Appliance Installation Service, and MaintenanceAppliance Operation Notices Burn-in Period Inputs and EfficienciesInputs Orifice Sizes Sea Level to High Altitude All ModelsIs OFF Gas Controls / Control Compartment AccessON/OFF Switch Switches from Operation and care of your applianceRemote Control System Key Lock Intermittent/Standing Pilot ModeSlider Switch Remote Position Room Temperature Flame On Maximum Level IndicatiorsClean Logs and Burner See Maintenance Schedule,Glass Cleaning Clean Control CompartmentSee Figure Install only when fireplace is OFF and ColdHot Glass will Cause Burns Removing Glass Doors, Mesh Pull Screens, and Modesty PanelControl Side Top view of burner shown IMPORTANT! Ember pieces must be As Small and Thin as a dimeBag of Glowing Embers Control SideLog, Top Front Install logs reference and TableLog, Center Log, Top Right Log, Top LeftGroove Location PinBurner Flame Appearance Control Side Burner AdjustmentsBurner Air Shutter Adjustment Guidelines Flame Appearance and SootingElectronic Appliance Checkout Pilot AssemblyWiring Diagram Ordering Replacement partsBag of Glowing Embers Bag of Volcanic Stone Accessory ComponentsAndiron Kits Ceramic and Porcelain Panel KitsBarrier Screen Kits Outdoor KitArch Screen Kits Classic Screen KitsBe performed Slide the switch on the receiver to OFFInstructions D’ALLUMAGE Do not touch or attempt to clean glass while hot Maintenance ScheduleSymptom Possible causes Corrective action Troubleshooting the Montebello LSM40ST FireplaceGas Controls SIT Electronic Replacement Parts ListCat. No Replacement Parts Illustration Page 506025-05 Rev. C 05/2011