Honeywell XG1000 manual Remote account username and password, Black wire to Pin Red wire to Pin

INSTALLATION CHECKLIST ///

■XG1000 Controller and a Honeywell Bridge

■6160 Alpha panel as a debugging tool

■Confirm address 22 is open and configured as a keypad device.

Please note that if 22 is already is use, the existing keypad will need to be moved to a different address

■Remote account username and password

INSTALL & VALIDATE XG1000 CONTROLLER ///

1.Locate the customer’s external internet connection and the in-home router. Find one unused LAN RJ-45 port on the router. Then, use an Ethernet cable to connect the LAN RJ45 port on the XG1000 Controller to the unused LAN RJ45 port on the router.

XG1OOO CONTROLLER

1	2	3	4
				INTERNET
	LAN		WAN	LAN
	ROUTER			DSL/CABLE MODEM
	(NOT INCLUDED)			(NOT INCLUDED)

2.Connect XG1000 Controller to power and verify the following:

■The XG1000 ‘X’ power LED is lighted BLUE

If the power LED is not lighted, please re-check all power connections (see Troubleshooting Section)

■The XG1000 LAN/Link LED is lighted GREEN

If the LAN/Link LED does not light check the Ethernet connection and/or try using a different Ethernet cable (see Troubleshooting Section)

3.Wait up to 3 minutes for the XG1000 Controller to initialize.

4.Check and confirm LED marked ‘REM’ is solid GREEN (REM LED is the health indicator for remote access).

	DEV			LAN
ACT	STAT	REM	ACT	LINK

REMOTE CONNECTIVITY LAN LINK POWER INDICATOR

HONEYWELL BRIDGE INSTALLATION PROCEDURE ///

1.Connect the Honeywell Bridge to the Honeywell Panel (or the keypad if possible)

The Bridge connects just like an additional keypad (SafeWatch Pro 3000 terminals noted). Please power down the Honeywell Panel prior to beginning this process:

■Black wire to Pin 4

■	Red wire to Pin 5			HONEYWELL
■	Green wire to Pin 6			BRIDGE
■	Yellow wire to Pin 7
	SAFEWATCH PRO 3000
	CONTROL TERMINAL STRIP
	AUX.	AUX.	DATA	DATA
	–	+	IN	OUT
	4	5	6	7
	TO KEYPAD BLK WIRE			BRIDGE YEL WIRE
	TO KEYPAD RED WIRE			BRIDGE GRN WIRE
	TO KEYPAD GRN WIRE			BRIDGE RED WIRE
	TO KEYPAD YEL WIRE			BRIDGE BLK WIRE

NOTE: The existing keypad will remain connected. Mount the Bridge device near the alarm panel away from large metal objects. If necessary, you can extend the length of the wire using four conductor cable and wire nuts. For best results the bridge device should be mounted as high as possible, preferably at least 6 feet above the floor.

2.Re-connect power to the Honeywell Panel.

3.The LED on the Honeywell Bridge should light up and display RED – If the LED does not light up, the Bridge is not receiving power, please check all connections (see Troubleshooting Section).

If the LED changes from solid GREEN to solid RED within the first 60 seconds after applying power, and remains solid RED, the Controller and the Bridge may be having difficulty communicating. Please perform the Range Test described in the Troubleshooting Section of this manual.

4.Go to existing alarm keypad. Disarm the alarm system, establish access to alarm system via the “Installer Code” (may need to re-power unit and use ‘#*’ to set an installer code).

5.Connect a 6160 ALPHA KEYPAD if existing keypad is not alpha. From the keypad enable

the keypad address 22 in the alarm panel for use by the Honeywell Bridge (for the SafeWatch Pro 3000, enter ‘[ 1, 0 ]’ in location ‘*195’).

I 2