Honeywell 6271 manual System Overview Contd, Fire Protection

Page 11

System Overview (Cont'd)

Entry/Exit Delays

Your system has preset time delays, referred to as exit delay and entry delay. Whenever you arm your system, exit delay gives you time to leave through the designated exit door without setting off an alarm. Exit delay begins immediately after entering any arming command, and applies to all modes of arming protection. If programmed, a slow beeping will sound throughout the exit delay period. Additionally if programmed, a rapid beeping may sound during the final 10 seconds of the exit delay period.

Note: 6271V and 6271CV Only – On some systems, pressing the Voice Status Icon restarts the exit delay. Refer to your control panel User Guide to see if this is applicable on your system.

Entry delay gives you time to disarm the system when you enter through the designated entrance door. But the system must be disarmed before the entry delay period ends, or an alarm will occur. The keypad will beep during the entry delay period, reminding you to disarm the system. Ask your installer about the delay times programmed into your system.

Alarms

When an alarm occurs, the TouchCenter (and any other keypads) and external sounders will sound, and the zone(s) causing the alarm are displayed. If your system is connected to a central monitoring station, an alarm message will also be sent. To stop the alarm sounding, simply disarm the system.

Memory of Alarm

When an alarm condition occurs, the number(s) of the zone(s) that caused the problem are displayed, along with the type of alarm. These remain displayed until cleared.

Note: If you change screens, the alarm in memory can be viewed and cleared by selecting the Display Faults button on the Arming Screen.

Fire Protection

The optional fire protection portion of your security system (if used) is always on and will sound an alarm if a fire condition is detected. Note: If a fire or smoke detector develops a low battery, a “Fire Maintenance” message is displayed. To determine which zone is causing the problem, go to “Display Faults” to determine which zone has the low battery indication.

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Ademco 6271 Series TouchCenter Keypads Table of Contents Table of Contents Contd Glossary TouchCenter Interface About the TouchCenterIntroduction About Your Home Screen About the TouchCenter contdNavigating through the TouchCenter Icon Location Function Navigation Icon DescriptionsStay TouchCenter Arming ScreenAway Icon Meaning NightMore ChoicesBurglary Protection System OverviewIntroduction to Your System Fire Protection System Overview ContdExtended Functionality Safe ModeCarbon Monoxide Protection User CodesSystem Overview Contd System Overview contd Security System Operation How to Arm the SystemFeatures for Each Arming Mode Arming Exit Entry Perimeter Interior Mode Delay ArmedScreen Action Security System Operation contdARM Selected How to Arm Multiple PartitionsTo arm multiple partitions Bypass Zones, Enter Code How to Display FaultsBypass How to Bypass ZonesTo bypass zones do the following Press the Bypass Selected How to Remove Bypassed Zones Enter your Authorized Code How to Clear a Control Panel MessageHow to Hide a Control Panel Message To disarm the system when entering the premises How to Disarm the SystemDisarm Selected button. Arm or Not Ready Fault if any zone isHow to Check the Status of Other Partitions Enter the code authorized to access How to Send Emergency Messages Next and Previous buttons How to View the Event LogWhen All Partitions or All Events Next and Previous buttons willSilencing and Clearing a Fire Alarm Fire Alarm System OperationIntroduction to Fire Alarm System Operation Case of Fire AlarmSilencing and Clearing a Carbon Monoxide Alarm Fire Alarm System Operation ContdCase of Carbon Monoxide Alarm Fire Alarm System Operation contd Authority Levels User Code SetupIntroduction to User Code Setup Access User Setup as follows User Code Setup contdHow to Access User Setup Authorized Code How to Add a UserAdd a user as follows Digits Enter User Code… displayedSelected, the Allow Arm/Disarm from Delete a User as follows How to Delete a UserInstructions Enter Authorized Code How to Edit a UserEdit a user as follows Console Emulation Mode Advanced System FeaturesIntroduction to Advanced System Features To access the TouchCenter Keypad, do the following Advanced System Features ContdHow to Enter Console Emulation Mode Introduction to Recording and Retrieving Messages Voice Messages 6271V/6271CV OnlyRecording a Voice Message Voice Messages ContdTo retrieve a voice message, do the following Retrieving and Deleting a Voice MessageOn Security system is armed Summary of LED OperationLED Operation LED Description ArmedAccess the Setup features as follows TouchCenter SetupHow to Access TouchCenter Setup Options How to Access SetupHow to Adjust the Volume TouchCenter Setup ContdHow to Adjust the Contrast Backlight Off After arrow button. a How to Select Screen Backlight Off Activation TimeButton. a Settings Changed! pop-up How to Select Homepage After Time TouchCenter Setup Contd Setting Daylight Savings Time How to Set the Time and DateTouchCenter Setup Contd To set the current time, do the following Setting Current TimeTouchCenter Setup Contd TouchCenter Setup Contd TouchCenter Setup Contd Operating Modes Chime, Voice, and Voice Chime Operating ModesPress the Operating Modes How to Access Operating ModesAccess the Operating Modes feature as follows TouchCenter Operating Modes contdHow to Access Language Selection Maintaining Your System How to Clean your TouchCenterClean the TouchCenter as follows Routine Care Glossary Glossary Contd ONE Year Limited Warranty

6271 specifications

The Honeywell 6271 is an advanced security keypad designed to enhance user experience while providing robust safety features for home and business environments. This versatile keypad is primarily used in Honeywell's security systems and is well-regarded for its user-friendly interface and array of functions.

One of the standout features of the Honeywell 6271 is its large, intuitive touchscreen display. The 7-inch screen allows for easy navigation through the various options, making it simple for users to arm or disarm their security system, view system status, and access other settings. The high-resolution display enhances visibility, ensuring ease of use even in low-light conditions.

The Honeywell 6271 incorporates built-in Z-Wave technology, which supports seamless integration with a wide range of smart home devices. This feature allows users to control locks, lights, and thermostats directly from the keypad, thereby streamlining home automation and enhancing convenience. Additionally, the Z-Wave capabilities enable remote management, allowing homeowners and business owners to monitor and control their security settings from their smartphones or tablets.

Another significant aspect of the Honeywell 6271 is its compatibility with various Honeywell security systems. This ensures that users can easily incorporate the keypad into their existing setups without the need for extensive modifications. The device is designed to work alongside Honeywell's alarm systems, providing a cohesive and efficient response to potential security threats.

In terms of security, the Honeywell 6271 features advanced encryption and authentication measures, offering enhanced protection against unauthorized access. The keypad supports user-defined codes, enabling multiple family members or staff to have their unique access credentials. Moreover, built-in alarm functionality allows for immediate alerts in the event of a breach, ensuring that users are quickly informed of any suspicious activity.

Aesthetically, the Honeywell 6271 boasts a sleek and modern design that can complement any interior décor. Its ergonomic layout and responsive touch interface make it not only an effective security tool but also a stylish addition to any home or office.

In summary, the Honeywell 6271 combines cutting-edge technology with practical usability, boasting features such as a large touchscreen display, Z-Wave integration, robust security measures, and compatibility with existing security systems. This keypad exemplifies Honeywell’s commitment to providing innovative and efficient solutions for modern security needs. Its advanced features make it an essential component of any comprehensive security system.
Top Page Image Contents