State Industries GPO84 315, GPO75 385, GPO75 455, GPO69 700 warranty Asme

C O M M E R C I A L

TITAN™

Commercial Oil Water Heater

SPECIFICATIONS

	Storage		Firing		Output (Gallons)				Dimensions In Inches					Approximate		Water
													Motor	Shipping
	Capacity	Input*
Model Number						Recovery										Connections
	U.S.	BTU/Hr.	Rate										HP	Wt. (lbs.)
			GPH
	Gallons			80°F Rise		100°F Rise	140°F Rise	A	B	C	D	E		Standard	ASME	In	Out
GPO 86 199OE	86	199,000	1.42	241		193	138	743⁄4	673⁄4	27	6	231⁄8	1⁄8	568	—	11⁄2	11⁄2
GPO 86 245OE	86	245,000	1.75	297		238	170	743⁄4	673⁄4	27	8	231⁄8	1⁄8	557	—	11⁄2	11⁄2
GPO 84 315OE**	84	315,000	2.25	382		305	218	743⁄4	673⁄4	27	8	231⁄8	1⁄8	557	668	11⁄2	11⁄2
GPO 75 385OE**	75	385,000	2.75	467		373	267	743⁄4	65	251⁄4	8	233⁄4	1⁄8	638	730	11⁄2	11⁄2
GPO 75 455OE**	75	455,000	3.25	552		441	315	743⁄4	66	251⁄4	8	233⁄4	1⁄8	647	748	11⁄2	11⁄2
GPO 69 700OE**	69	700,000	5.00	848		679	485	793⁄4	703⁄8	303⁄16	10	293⁄8	1⁄8	739	853	11⁄2	11⁄2

*Based on No.2 fuel oil. Capacity ratings are actual heater performance at 80% thermal efficiency. **These models are available with ASME construction. When ordering ASME construction, add “A” to

end of model model. Example: GPO 69 700OE A

NOTE: Above 2000´ altitude, input ratings should be reduced 4% for each 1000´ above sea level.

				37 ˝
		D		11⁄2˝ NPT INLET &
				OUTLET OPENINGS
				1˝ NPT T&P VALVE OPENING
			273⁄4˝
ELEC.
ENTR	Y
A
				B

C

E

ASME

(ON SELECTED MODELS)

GPO SUGGESTED SPECIFICATION

Water heater(s) shall be commercial oil model number______________or equivalent. Heater(s) shall have a minimum oil firing rate of ______________gph at 100°F temperature

rise and a storage capacity of _________________gallons. The 160 psi working pressure tank shall be glass-lined with the alkaline borosilicate composition being

fused to the steel at 1600° and be equipped with 1-1/3” water inlet and outlet openings, and 2-3/4” x 3-3/4” boiler-type hand-hole cleanout (2) on GPO84 315 and larger or ASME models. The tank shall be insulated with 2˝ of vermin proof fiber glass insulation. The outer jacket shall have baked enamel finish over a bonderized undercoating. The burner shall be Underwriters’ Laboratories listed and have a ___________________(one or two) stage oil pump. The burner shall have flame retention,

interrupted ignition and be equipped with primary controls which will provide for 15 second safety shutdown in the event of flame failure. The heater(s) shall be factory equipped with primary controls which will provide for 15 second safety shutdown in the event of flame failure. The heater(s) shall be factory equipped with temperature limiting device, drain valve, flame observation port and 180° adjustable thermostat having upper and lower sensing bulbs which average the water temperatures at the top and bottom of the tank for maximum water temperature control. A pressure and temperature relief valve shall be furnished and installed by the factory. Heater tank shall have a 3 year limited warranty against corrosion and tank failure due to sediment buildup as outlined in the warranty.

CAUTION: Unit must be installed on non-combustible surface.

MULTIPLE INSTALLATIONS

Furnish and install __________________models as specified with a State (2, 3, or 4) heater manifold kit, package number _____________.

For more information on Titan™ contact: State Water Heaters

500 Tennessee Waltz Parkway, Ashland City, TN 37015

800-365-0024 Toll-free USA www.statewaterheaters.com

SCOSS00105 July 2008R