Logitech DLA2RF manual Connections, Amplifier Input

Page 13

DLA2RF 2 Room Speaker Selector

3. Connections

AMPLIFIER INPUT

Use 16 AWG stranded copper speaker wire to connect from a speaker level output of an A/V receiver, stereo receiver, or amplifer. Turn power for the output device OFF before making con- nections.

To make connections:

1.Cut the ends of the wire to length, allowing some free play (about 6 inches of slack) to allow for movement when physically connecting the wire.

2.Using wire strippers, remove 3/8 inch of insulation, then twist the wire to ensure that no stray strands are evident.

3.Deﬁne positive (+) and negative (-) at the ampliﬁer end and the DLA2RF end of the wire run and use the same conductor on each end.

4.Lift up each ﬂip-lock connector until it is locked in the up position.

5.Place the bare lead from each speaker wire from the receiver/ampliﬁer into the holes of the Ampliﬁer Inputs terminal of the DLA2RF, maintaining the polarity of each lead (+ to +, - to -).

Note: To avoid damage to the receiver/ampliﬁer, DO NOT allow speaker leads to touch

each other.

DLA2RF

125Watts per Channel

Max

Speaker

Cables

AMPLIFIER

INPUT

CLASS 2 WIRING

L RL R

+

-

A B

Receiver/Amplifier

Output

Figure 3-1: Receiver/Ampliﬁer Output to DLA2RF Ampliﬁer Input

© 2007 • All rights reserved.

11

Image 13

Contents DLA2RF Page Package Contents Safety InformationContents Introduction Aton DLA2RF Accessories FeaturesFront Panel Indicator/Button FunctionConector Function Rear PanelStandard Audio/Video or Stereo Receiver System Design Overview A/V Receiver Zone 2 Application Zone 2 Output of an A/V or Stereo ReceiverDLA2RF External AmpliﬁerProcessor/Pre-Amp Ampliﬁer Application Amplifier Input ConnectionsImportant Note PWR in Connection Aton PORT/RF ReceiverVolume Settings Settings & OperationReceiver/Ampliﬁer Volume Settings Volume Status BarRoom Volume Adjustment Press Default VolumeSetting a Scene Scene PresetsRecalling a Scene Preset Button Function RF Remote ControlAudio Symptom Possible Cause Solution TroubleshootingRF Control Symptom Possible Cause Solution Dimensions Appendix a SpecificationsConnections RF Remote/Receiver BaseFigure B-1 Room Identiﬁcation Labels Appendix B Room Identification LabelsDLA2RF 2 Room Speaker Selector Limited Warranty Page Selector de Altavoces De 2 Cuartos Page Contenidos del paquete Visión de conjunto del diseño del sistema ÍndiceIntroducción Accesorios de Aton DLA2RF CaracterísticasIndicador/Botón Función Panel FrontalConector Función Panel PosteriorReceptor Audio /Vídeo o Receptor Estéreo Convencionales Visión de conjunto del diseño del sistemaSalidas en «Zone 2» de un Receptor A/V o Receptor Estéreo Ampliﬁcador Externo Dibujo 2-4 Aplicación de Ampliﬁcador Procesador/Pre-amp Entrada del Ampliﬁcador «AMPLIFER INPUT» ConexionesLas Salidas del Emisor IR «IR Emitter OUTPUTS» Salidas de Altavoces «SPEAKER OUTPUTS»La Conexión de «PWR IN» Puerto ATON/Receptor RF «ATON PORT/RF Receiver»Ajustes de Volumen de Receptor/Ampliﬁcador Ajustes de VolumenPantalla para monitoreo del nivel del volumen Ajustes y OperaciónAjuste de Volumen del Cuarto «ALL ON/OFF» Botón de encender/apagar todo Volumen PreseleccionadoPara Preseleccionar una Escena Escenas PreseleccionadasReestablecer una escena preseleccionada Botón Función Control Remoto RFAudio Síntoma Causa Posible Solución Problemas y SolucionesControl Remoto RF Síntoma Causa Posible Solución Síntoma Causa Posible SoluciónSíntoma Causa Posible Solución Apéndice a Especificaciones DimensionesConexiones Control Remoto RF/Base del ReceptorDibujo B1 Etiquetas de identiﬁcación del cuarto Apéndice B Etiquetas de identificación del cuartoPage 9900879 Reva Garantía limitadaFolding Album Fold Center Staple