Whirlpool BFG1H5040T3NOV 5K, BFG1F5040T3PV Installing Your GAS Water Heater, Consumer Information

Page 3

INSTALLING YOUR GAS WATER HEATER

Important Information About This Water Heater

This gas water heater was manufactured to voluntary safety standards to reduce the likelihood of a flammable vapor ignition incident. New technology used in meeting these standards makes this product more sensitive to installation errors or improper installation environments. Please review the Installation Checklist found at the end of the installation instructions section and make any required installation upgrades or changes.

Consumer Information

This water heater is design-certified by CSA International as a Category I, non-direct vented water heater which takes its combustion air either from the installation area or from air ducted to the unit from the outside.

This water heater must be installed according to all local and state codes or, in the absence of local and state codes, the “National Fuel Gas Code”, ANSI Z223.1(NFPA 54)- latest edition. This is available from the following:

CSA America, Inc.

8501 East Pleasant Valley Road

Cleveland, OH 44131

National Fire Protection Agency

1 Batterymarch Park

Quincy, MA 02269

Check your phone listings for the local authorities having jurisdiction over your installation.

installed in accordance with Massachusetts Plumbing and Fuel Gas Code 248 CMR Section 2.00 and 5.00.

A data plate identifying your water heater can be found next to the gas control valve/thermostat. When referring to your water heater, always have the information listed on the data plate readily available.

Retain your original receipt as proof of purchase.

Unpacking the Water Heater

WARNING

Excessive Weight Hazard

Use two or more people to move and install water heater.

Failure to do can result in back or other injury.

IMPORTANT: Do not remove any permanent instructions, labels, or the data label from either the outside of the water heater or on the inside of water heater panels.

Remove exterior packaging and place installation com- ponents aside.

Inspect all parts for damage prior to installation and start-up.

Completely read all instructions before attempting to assemble and install this product.

After installation, dispose of/recycle all packaging materials.

Consumer Responsibilities

This manual has been prepared to acquaint you with the installation, operation, and maintenance of your gas water heater and provide important safety information in these areas.

Read all of the instructions thoroughly before attempting the installation or operation of this water heater.

Do not discard this manual. You or future users of this water heater will need it for future reference.

Service to the Flame Lock™ Safety System should only be performed by a qualified person.

Examples of a qualified person include: licensed plumbers, authorized gas company personnel, and authorized service personnel.

IMPORTANT: The manufacturer and seller of this water heater will not be liable for any damages, injuries, or deaths caused by failure to comply with the installation and operating instructions outlined in this manual.

If you lack the necessary skills required to properly install

 

this water heater, or you have difficulty following the

 

instructions, you should not proceed but have a qualified

 

person perform the installation of this water heater.

 

Massachusetts code requires this water heater to be

3

 

Image 3
Contents Installation Instructions Use & Care Guide Table Of Contents Water Heater SafetyUnpacking the Water Heater Installing Your GAS Water HeaterImportant Information About This Water Heater Consumer InformationSite Location Location RequirementsClearances and Accessibility Gas Supply Gas RequirementsGas Pressure Combustion Air Supply and Ventilation Unconfined Space Confined SpaceAll Air from Inside the Building Louvers and Grilles All Air from OutdoorsVent Pipe Size Drafthood InstallationVent Connectors Vent Pipe SystemVertical Exhaust Gas Vent Chimney ConnectionWater System Piping Piping InstallationClosed System/Thermal Expansion Relief Valve and Pipe Insulation Some Models Temperature and Pressure Relief ValveSolar Installation Special ApplicationsCombination Space Heating/Potable Water System Installation Checklist Lighting Instructions Operating Your Water HeaterChecking the Draft Water Temperature RegulationOperational Conditions Maintenance of Your Water Heater Routine Preventive MaintenanceDraining and Flushing Natural Gas Burner Low Nox Replacement PartsRemoving the Manifold Assembly Removing the Burner from the Manifold AssemblyExternal Inspection & Cleaning of the Flame-trap Cleaning the Combustion Chamber and Flame-trapReplacing the Thermocouple Replacing the Manifold Assembly Testing the Igniter SystemPiezoelectric Igniter System Removing and Replacing the Gas Control Valve/Thermostat Flame Lock Safety System Operational ChecklistSlow HOT Water Pilot Light Troubleshooting Flowchart Repair Parts List Repair Parts IllustrationListed Parts Kits and Illustrations

192906, BFG1F4034T3PV, BFG1F4034T3PV 7K, 195102, 211456 specifications

The Whirlpool BFG2H4040T3NOV E and BFG1J4040T3NOV 5K are high-efficiency gas water heaters that cater to the needs of modern households with their cutting-edge technologies and features. Engineered with the latest advancements, these models ensure optimal performance, energy efficiency, and user convenience.

One of the standout features of the Whirlpool BFG series is its robust build quality. Both models are designed with a cylindrical stainless-steel tank that enhances durability and longevity. The insulation used in these heaters minimizes heat loss, ensuring that water remains hot for an extended period while reducing energy consumption. This characteristic not only saves on utility bills but also contributes to environmentally friendly practices.

Additionally, the BFG2H4040T3NOV E and BFG1J4040T3NOV 5K incorporate smart technology that simplifies the user experience. The thermostatic control allows homeowners to set and maintain precise water temperatures according to their preferences, providing comfort and convenience. Furthermore, these models are equipped with a high-efficiency burner system that maximizes the heating process, ensuring that hot water is readily available when needed.

Safety is a significant focus of Whirlpool's design philosophy. The BFG series features advanced safety mechanisms including a flame arrestor that prevents combustion incidents, along with a built-in pressure relief valve. These safety features offer peace of mind for users, ensuring worry-free operation in everyday use.

Moreover, the Whirlpool BFG model line is designed with installation flexibility in mind. They can be seamlessly integrated into various home designs, whether residential or commercial. The compact nature of these heaters allows for space-saving installations while delivering high output efficiency.

The BFG series also emphasizes user serviceability with clear instructions for maintenance and troubleshooting, enabling homeowners to address common issues effectively without requiring professional assistance. This aspect further enhances the overall ownership experience, making these water heaters an excellent choice for energy-conscious consumers.

In summary, the Whirlpool BFG2H4040T3NOV E and BFG1J4040T3NOV 5K stand out in the market due to their exceptional durability, advanced technology, safety features, and ease of installation. With their energy-efficient design and user-friendly functionality, these gas water heaters provide the perfect solution for families seeking reliable hot water solutions.