Kicker 10IX500.1 Ixsm, Model External Fuse Power/Ground Wire Kicker Wiring Kit, Sold separately

Page 3

IXSM

sold separately

Wiring: Disconnect the vehicle’s battery to avoid an electrical short. Then, connect the ground wire to the amplifi er. Make the ground wire short, 24” (60cm) or less, and connect it to a paint-and-corrosion-free, solid, metal area of the vehicle’s chassis. Adding an additional ground wire of this same gauge (or larger) between the battery’s negative post and the vehicle chassis is recommended.

The IX amplifi er has dual input sensitivity differential RCA inputs which will receive either high or low level signals from your car stereo’s source unit. Ideally, when connecting the source unit to the amplifi er, the IX amplifi er’s input level switch should be set to “LO” and a low-level signal should run from the source unit’s stereo RCA output to the stereo RCA input on the end panel of the amplifi er using RCA interconnect cable. If a low-level stereo RCA output is not available on the source unit, the signal can be delivered to the amplifi er using the high-level speaker outputs on the source unit. Set the input level switch on the end panel of the amplifi er to “HI”. Crimp and solder RCA connectors to the end of the speaker wire running from the high-level speaker outputs on the source unit and connect the wire to the RCA Inputs on the end panel of the amplifi er or simplify the installation by using a KICKER ZISL as shown below. Either input method will provide a low-level output signal at the RCA output, which effectively passes the audio signal to another amplifi er or component. Keep the audio signal cable away from factory wiring harnesses and other power wiring. If you need to cross this wiring, cross it at a 90 degree angle.

source unit

core conductor

to amplifi er

KICKER ZISL

high-level speaker

 

 

 

outputs

 

 

 

+

 

OR

to amplifi er

–

shield

 

source unit high-level

 

 

 

 

 

speaker outputs

Install a fuse within 18” (45cm) of the battery and in-line with the power cable connected to your amplifi er. Install a second fuse within 18” (45cm) of the amplifi er. If you ever need to remove the amplifi er from the vehicle after it has been installed, the ground wire should be the last wire disconnected from the amplifi er--just the opposite as when you installed it.

Model

External Fuse

Power/Ground Wire

KICKER Wiring Kit

 

(sold separately)

 

 

IX500.1

2 x 50 Ampere

4 Gauge

PK4, CK4, ZCK4

IX1000.1

2 x 100 Ampere

4 Gauge

PK4, CK4, ZCK4

3

2010 IX 500.1 1000.1 RevC.indd 3

11/12/2009 2:15:06 PM

Page 2 Page 4
Image 3
Page 2 Page 4
Contents IX Amplifier Model IX500.1 IX1000.1 InstallationIX500.1 PerformanceModel External Fuse Power/Ground Wire Kicker Wiring Kit IxsmSold separately Mono Operation OperationMinimum impedance of 2 ohms Conductor phone cable Slide the housing until it snaps Into the metal bracketTroubleshooting IX1000.1 A. Only EE.UU. solamente Nur USA Les USA Seulement IX500.1Modelo IX500.1 IX1000.1 Amplificador DE LA SerieManual del propietario RendimientoNo incluido KickerSe vende por separado Conexión a tierra o blindajeFuncionamiento Monofónico FuncionamientoImpedancia mínima de 2 ohmios Monte el Soporte de Metal Encaje en el soporte de metalCable de teléfono de 4 conductores Resolución DE Problemas IX500.1 Modell IX500.1 IX1000.1 Verstärker DER IX.1 SerieBenutzerhandbuch IX500.1 LeistungNicht inbegriffen OderModell Externe Sicherung Massekabel Kicker Verkabelungssatz Separat erhältlichMONO-BETRIEB BetriebMinimalimpedanz von 2 Ohm Metallhalterung Schieben Sie das Gehäuse Befestigen EinrastetVieradriges Telefonkabel Problembehebung IX500.1 Amplificateur Série IX.1 Manuel d’utilisation IX500.1 PerformancesModèle IX500.1 IX1000.1 Vers l’amplifi cateur Vendu séparémentÂme Masse ou blindageMise sous tension à distance Fonctionnement MonoUtilisation Masse Fusible ExterneCâble téléphonique à 4 conducteurs MétalliqueEN CAS DE Difficulté IX500.1 Box 459 Stillwater, Oklahoma 74076 USA 405 Electronics Limited WarrantyGarantía Internacional International WarrantyStillwater Designs

10IX500.1, IX1000.1, 10IX1000.1, IX500.1 specifications

The Kicker IX series of amplifiers, including the 10IX1000.1, IX500.1, IX1000.1, and 10IX500.1, represents a fusion of power, efficiency, and advanced technology tailored for car audio enthusiasts. Designed to seamlessly integrate into any audio system, these amplifiers deliver powerful performance alongside remarkable versatility.

One of the standout features of the Kicker IX series is their compact design, which allows for easy installation in tight spaces without compromising on output power. The 10IX1000.1, for example, boasts a potent output of up to 1000 watts RMS, making it an excellent choice for those seeking to drive subwoofers with authority. The IX500.1 and 10IX500.1 amplify power ratings of 500 watts RMS, which cater perfectly to mid-range subwoofers, providing an ideal balance of quality audio and manageable size.

These amplifiers are built with advanced Class D technology that enhances performance by maximizing energy efficiency while minimizing heat production. This results in more efficient power handling and reduced strain on your vehicle’s electrical system. Each model features a variable low-pass crossover, allowing users to customize their bass response to complement their specific audio setup.

Kicker's IX amplifiers are also equipped with a powerful bass boost feature, enabling users to enhance low-frequency sounds for a more impactful listening experience. The inclusion of a remote bass control option allows for convenient adjustments on the fly, ensuring your audio can adapt to different genres or personal preferences.

Durability is a critical aspect of the Kicker IX series, as these amplifiers are designed to operate reliably under demanding conditions. The rugged construction is engineered to withstand the rigors of automotive environments while providing optimal sound quality. Additionally, each model includes a range of protection features such as thermal, overload, and short circuit protection, ensuring long-lasting performance without the risk of damage.

In summary, the Kicker 10IX1000.1, IX500.1, IX1000.1, and 10IX500.1 amplifiers exemplify the best in modern car audio technology. With their compact designs, powerful output capabilities, innovative features, and superior durability, these amplifiers are well-suited for any enthusiast looking to elevate their car’s audio system. Whether you’re looking to drive powerful subwoofers or enhance the overall sound quality in your vehicle, Kicker's IX series offers unmatched performance and flexibility.
Top Page Image Contents