Installation, Power, Procedure | Bosch Appliances LTC 8785 specs

LTC 8785 Series Instruction Manual Installation	EN 8

4INSTALLATION

4.1Power

Model No.1	Rated Voltage	Voltage Range Power2
LTC 8785/60	120 VAC, 50/60 Hz	108 to 132	12 W
LTC 8785/50	220-240 VAC,50/60 Hz 198 to 264		12 W

1These units may be supplied with grounded power cords;

grounding should not be defeated.

2Nominal power at rated voltage.

4.2Procedure

Refer to ILLUSTRATIONS as necessary per the following instructions.

If possible, install the LTC 8785 Series close enough to the existing LTC 8568/00 Signal Distribution Unit

(or LTC 8569 Series Code Merger) so that the supplied 2 meter (6 ft) data cable will reach one of the outputs of the LTC 8568/00 unit. The data output cables corresponding to the older TC8561 Series Receiver/drivers will need to be removed from the existing LTC 8568/00 and connected to the outputs

of the LTC 8785 Series. The older LTC 8568/00 mating connector blocks can be connected directly to the connectors on the rear panel of the new LTC 8785 Series. If necessary, the shielded-twisted pair cables can be removed from the older connectors and wired directly to the new connectors.

If these units are placed at a more distant location, the data output cables for the receiver/drivers will need to be extended or re-routed appropriately to the new site.

The data input to the LTC 8785 Series are made to the 9 pin D-connector on the rear panel. The supplied data cable must be prepared so it can be used to connect to an output of the existing LTC 8568/00 Signal Distribution Unit.

•Prepare the data cable by cutting off the end of the cable containing the male 9-pin D- connector.

•Locate the three conductors corresponding to Data + (pin 1), Data - (pin 2), and Shield (pin 3).

•Strip the ends of the three conductors approximately 6 to 7 mm (1/4 in) so they can be connected to one of the output terminal blocks of the existing LTC 8568/00 unit.

•Connect the conductor corresponding to pin 1 to a “+” terminal of the LTC 8568/00 output; pin 2 connects to a “-” output, and pin 3 to a “S” output. If necessary, a shielded-twisted pair cable can be used to extend the data line between an output of the LTC 8568/00 and the input to the LTC 8785 Series.

•Install the AC power cord to the appropriate power source. The POWER LED on the code converter unit’s front panel should light when power is applied.

4.3Cover Removal

WARNING: Removal of the cover should only be performed by qualified service personnel-- not user serviceable. The unit should always be unplugged, before removing the cover and remain unplugged while the cover is removed.

4.4Mounting Options

4.4.1 Rack Mount

The units are supplied from the factory in an enclosure suitable for rack mounting in an EIA 19-inch rack. The enclosure is one EIA standard rack width (19 in) by two rack units high (3 1/2 in). Peel off the four rubber feet located on the bottom of the enclosure before installing it into a console.

4.4.2 Desk Top Mount

If the unit is not going to be rack mounted, the enclosure’s mounting ears should be removed. The cover of the unit must be removed before access to the mounting ears is possible. Removal of the cover should only be performed by qualified service personnel. The unit should always be disconnected from the AC power source before removing the cover.

The top cover is fastened to the case by four screws located on the rear of the unit. Once the screws have been removed, the cover slides back and off the unit. Remove each mounting ear by removing the screw holding the mounting ear to the enclosure chassis. See Figure 1.

Bosch Security Systems 19 April 2004

LTC 8785 specifications

The Bosch Appliances LTC 8785 is an innovative and high-performance appliance designed to enhance the modern kitchen experience. As part of Bosch's commitment to quality and efficiency, this model incorporates a range of features and technologies that make it a standout choice for discerning users.

One of the key features of the LTC 8785 is its advanced cooling system. Equipped with a state-of-the-art MultiAirFlow technology, the refrigerator ensures consistent temperatures throughout the unit. This technology works by using multiple airflow vents to distribute cold air evenly, preventing temperature fluctuations that can compromise food freshness. Additionally, the fridge features a NoFrost system, which eliminates the need for manual defrosting by preventing ice buildup.

Another remarkable characteristic of the LTC 8785 is its energy efficiency. It is designed with an EcoMode, which optimizes the appliance’s performance, ensuring that it consumes less energy during non-peak hours—helping homeowners to save on utility bills while also being environmentally friendly. The appliance carries an impressive energy rating, highlighting Bosch’s dedication to sustainability and power conservation.

In terms of usability, the Bosch LTC 8785 boasts an intuitive and user-friendly interface. The bright LED lighting not only illuminates the interior but also provides a modern aesthetic. The fridge includes adjustable shelves that can easily accommodate various sizes of groceries and eliminate wasted space. Furthermore, the door storage is thoughtfully designed to maintain organization, with compartments specifically tailored for bottles and condiments.

For those who enjoy gourmet cooking, the LTC 8785 caters to culinary enthusiasts with its dedicated cooling compartments. The crisper drawers are specially designed to maintain optimal humidity levels, perfect for storing fruits and vegetables. Additionally, the appliance supports a SuperCool function that allows for rapid cooling of newly added groceries to maintain freshness.

Moreover, Bosch incorporates smart technology into the LTC 8785—enabling connectivity with smart home systems. This feature allows users to monitor and control the appliance remotely through their smartphones, providing convenience at their fingertips.

In conclusion, the Bosch Appliances LTC 8785 is a premium cooling solution that combines cutting-edge technology, energy efficiency, and user-friendly design. Its sophisticated features cater to a wide array of needs, making it an excellent choice for any modern kitchen setup.