|
|
|
|
|
|
|
|
|
|
|
|
|
| PROGRAMMING |
|
| KEY | USER’S ACTIONS | DEFAULT | LED STATUS |
| ||||
| GUIDE Cont. |
| DETECTION MODE | Detection mode offers 3 different levels of | 3 | After pressing the DETECTION MODE |
| |||||
|
|
|
| |||||||||
|
|
|
|
|
| detection: |
| key, the red LED flashes quickly. After |
| |||
|
|
|
|
|
|
| pressing a number button, the red LED |
| ||||
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
| feature). MTF allows the Eagle to switch |
| flashes slowly. |
| |||
|
|
|
|
|
| from |
|
|
| |||
|
|
|
|
|
| detection from the normal approach |
|
|
| |||
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
| direction. |
|
|
|
| ||
|
|
|
|
|
|
|
| 1 | = |
|
|
|
|
|
|
|
|
|
|
| 2 | = |
|
|
|
|
|
|
|
|
|
|
| 3 | = |
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
| ||||
|
|
| IMMUNITY | Immunity alters the detection of unwanted | 2 | After pressing the IMMUNITY key, the |
| |||||
|
|
|
|
|
| disturbances within the field of motion |
| red LED flashes quickly. After pressing |
| |||
|
|
|
|
|
| detection. |
| a number button, the red LED flashes |
| |||
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
| 1 | = Extreme sensitivity |
| slowly. |
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
| 2 | = Normal Sensitivity |
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
| 3 | = Reduced sensitivity |
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
| ||
|
| DEFAULT VALUE |
|
| 1 = Restores default values for all |
| After pressing the DEFAULT VALUE |
| ||||
|
|
|
|
|
|
|
|
| key, the red LED flashes quickly. After |
| ||
|
|
|
|
|
|
|
| functions |
| pressing a number button, the red LED |
| |
|
|
|
|
|
|
|
| 2 = Boost Mode; Restores default |
| flashes slowly. |
| |
|
|
|
|
|
|
|
| values for all functions, and increases |
|
|
| |
|
|
|
|
|
|
|
| sensitivity for |
|
|
| |
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
| MANUAL |
| If a remote control is not available, you can adjust the sensitivity parameter ONLY, by means of the push |
| ||||||||
|
|
| buttons + (Plus) and - (Minus). |
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
The sensor parameters that are not accessible manually will remain at the factory preset values. Pressing the two push buttons, located on the circuit board, simultaneously for at least two seconds, will restore all default values.
+ Press to increase 
sensitivity by one unit
- Press to decrease sensitivity by one unit.
TROUBLE- |
|
|
|
|
|
| The door will not open & LED does not | 1. | Check supply voltage: 12 to 24 VAC: ± 10% |
| |
SHOOTING |
| light up |
| 12 to 24 VDC: |
|
|
|
| 2. | Check power connector |
|
|
| The sensor does not respond to the | 1. | Check remote control battery insertion |
|
|
| remote control | 2. | Check remote control battery voltage |
|
|
|
|
|
|
|
|
| The sensor does not respond to the code | 1. | Remove the cover and press the 2 buttons |
|
|
| entered with the remote control |
| simultaneously for at least two seconds. This will reset |
|
|
|
|
| the lock code to 0000. Then press the unlock button to |
|
|
|
|
| enable you to access the settings with the remote control. |
|
|
|
|
|
|
|
|
| The door open and closes constantly | 1. | Increase the tilt angle of the antenna |
|
|
|
| 2. | Reduce sensitivity |
|
75.1038 V3 Jun 2005 [Rev. June 10, 2005] | Page 7 of 8 |