Channel Plus H722C specifications Installing the Camera, Aiming the Camera, Attaching the Window

ChannelPlus Video Camera

The H722 video cameras are solid state cameras designed to fit deep double gang J-boxes. The H722 must be used with one of its companion channel injectors (H511HHR or H511BID). When used with an H511, video received from the H722 is used to create a new channel to add to existing television

channels. The H722 is connected to the H511 by a single run of CAT-5 wire. Although this camera mount is intended for use indoors, or under an

Installing the Camera

The H722 is designed to be mounted outside in a J-box or inside into dry wall. When mounting outside, use the supplied drip cap and gasket. When mounting inside, use the supplied CADDY® bracket.

The H722 series cameras work best when they are looking down on their subject. For a front door application, place the camera about 7 feet off the ground, adjacent to the door.

eave, a drip cap is supplied for use in exposed areas.

Two models are available:

Model H722

Black & White, 2 lux, 3.6 mm lens, smoked window

Model H722C

Color, 8 lux, 3.6 mm lens, smoked window

Note: The H722 is not a standalone video camera

Use only with an H511 channel injector.

Typical Installation

Connect the H722 camera using only one method:

1Terminate cable with a CAT-5 jack and connect to the H511 using supplied RJ45 jumper. (Also see example H628 manual).

2Wire camera or wall plate directly to the 8 position terminal block matching the CAT-5 wire colors to the colors on the terminal block. Insert wires and tighten screws.

Outside

Installation

Deep

double-gang

J-box

drip cap gasket

frame

Use

these parts

Inside

Installation

CADDY® bracket frame

Use

these parts

1
2
	Program
CAT-5 video
	CATV
Output	/Ant	Power
Channel Injector

Power the H511 last - make all cable and CAT-5 connections first.

Attach drip cap, gasket & frame

1

Insert 6-32 screws into frame and bottom holes of 2 gang box

	Note: bottom lip of drip
dripcap gasket frame
	cap goes inside frame.
	cap 180o for proper placement.)
	(You may have to rotate drip

Drywall

Make a square cut-out in the drywall that is 3¾” wide by 3½” high. Insert clip into drywall, and bend to form.

1

CADDY® bracket

Insert 6-32 screws into frame and bottom holes of CADDY® bracket.

Channel Injector

(H511HHR shown)Connect antenna or incoming cable to H511 CATV/Ant input.

Connect H511 output to splitter or distribution panel input. (See H511 manual)

Maximum CAT-5 run:

H722 to H511	300 feet
H722C to H511	100 feet

H722

(rear view)

Prepare the CAT-5 wires by stripping 1” of outer sheath and 1/8” of insulation. Insert wires into 8 position terminal block and tighten screws.

2

Insert camera at an angle and rotate into place. Make sure gasket is behind camera

Add RTV to seal from weather

Add top screws

3

Prepare the CAT-5 wires by stripping 1” of outer sheath and 1/8” of insulation. Insert wires into 8 position terminal block and tighten screws.

2

Insert camera at an angle and rotate into place.

Add top screws

3

Insert wire into terminal block and tighten screws. Use the color bar to match wire colors. The color bar has two rows, one for CAT-5 and one for quad wire:

-For CAT-5 wire, remove the default resistor and use all 8 wires.

-For quad wire*, leave default resistor in place and match four color wire.

*The H722/H722C was designed to work with CAT-5 wiring. Although the system will function with quad wire, CAT-5 delivers the highest quality picture. CAT-5 allows the use of an automatic line length sensor and picture compensator. Quad wire does not take advantage of this enhancement.

Aiming the Camera

Insert 1/8“ screwdriver in the steering slot below the lens. Using the screwdriver, bend the mount to point the camera in the desired direction.

4

Never use camera to bend the mount!

Attaching the Window

5

Window rides on the lip of the frame.

Rotate downward and snap into place.

Specifications:	typical @ 25OC ± 5OC
Model		H722	H722C
Image format		EIA (Black & White )	NTSC (Color)
Resolution, horizontal		525 lines	525 lines
Resolution		350 lines	350 lines
Minimum illumination		2 lux	8 lux
Signal to Noise ratio		>45 dB	>45 dB
AGC		Yes	Yes
Lens		3.6mm F2.0	3.6mm F2.0
Lens viewing angle		78O	78O
White balance		automatic	automatic
Electronic shutter speed		1/60 to 1/50000 second	1/60 to 1/50000 second
Maximum distance to H511		300 feet	100 feet

DECLARATION OF CONFORMITY

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.

Installation requirements:

FCC classifies this product under part 15 of its rules as a “television interface device”. Systems designed using television interface devices have the following legal requirements:

1)The modulated channel signal strength may not exceed 15.56dBmV at any television. Federal Regulation 47CFR15.115(b)(1)(i).

2)If an antenna is used in the system, the modulated channel signal strength may not exceed -51dBmV at the antenna input port. Federal Regulation 47CFR15.115(c)(4).

For the Installer:

Any system you design must comply with these regulations. As the installer, you are responsible. The H722 or H722C (when used with an H511) has the necessary characteristics to comply with the above requirements as designed without additional accessories.

The H511HHR is suitable for use with an antenna or with CATV systems. The H511BID is suitable for use with CATV systems only.