System Sensor BS5839 manual M200 Series Module Range, M200XE Short Circuit Isolator Module

Page 26

System Sensor Intelligent Product Range

M200 SERIES MODULE RANGE

INTRODUCTION

The family of input/output modules form part of System Sensor Europe’s Series 200 plus family. Single and multi-way models are available within the same mechanical package, reducing both the cost of installation and the mounting space required.

Their unique mechanical design allows each module to be mounted in either a wall box, on a DIN rail or within any type of enclosure. Irrespective of the mounting method chosen, the address switches and indicator LED’s are visible and accessible. To help engineers in the maintenance and fault-finding process, the LEDs, are multi-colour, providing diagnostic information regarding the status of each individual input/output.

Each module has built-in short circuit protection for the communications loop; however, to increase application flexibility, the isolators can be selected/deselected on an individual module basis.

For ease of installation, testing and maintenance, the field wiring terminals are of plug-in design.

Specifications

 

Operating Voltage:

15 to 30VDC

Operating Temperature: -20C to 60°C

Humidity Range:

0 to 95% Relative Humidity

Dimensions:

23mm x 93mm x 94mm (h x w x d)

 

(including terminal block)

Maximum Wire Gauge: 2.5mm²

M200-SMB Surface Mount Box

Dimensions:

134mm x 139mm x 40mm (h x w x d)

M200XE SHORT CIRCUIT ISOLATOR MODULE

The M200XE Isolator Module monitors the loop on either side of the module, and if it detects a short circuit will isolate that side. As a result, when used in conjunction with other isolator bases or modules, short circuits can be isolated from the remainder of the loop, thus minimising the effect of the fault. Once the short circuit is removed, the isolator will automatically restore the loop.

Specifications

 

Max standby current:

200µA at 24VDC

Max ON resistance:

0.13 Ohms at 15V

M210E SINGLE CHANNEL INPUT MODULE, M220E DUAL

CHANNEL INPUT MODULE AND M221E DUAL CHANNEL

INPUT, SINGLE CHANNEL OUTPUT MODULE

The M210E and M220E provide supervision of one or two input circuits from external devices; the M221E also provides an un-monitored single pole volt-free changeover contact for external devices. Input channels are capable of both latched and analogue supervision: There are three separate latched states, normal, open circuit and combined alarm/ short. The analogue supervision continuously monitors the supervised circuit, returning a signal proportional to the circuit resistance.

Specifications

 

M210E

 

Max Standby current

310µA at 24VDC (No communications)

M220E

 

Max Standby Current:

340µA at 24VDC (No communications)

M221E

 

Max Standby Current:

340µA at 24VDC (No communications)

Output Relay Rating:

2A at 30VDC, resistive load.

26

Note: This document is based on the recommendations of BS5839 Part 1: 2002. It is intended only as a guide to the application of fire detection systems.

Reference must be made to relevant national and local standards.

Page 25 Page 27
Image 26
Page 25 Page 27
Contents Guide to intelligent fire systems Guide to Intelligent Fire Alarm Systems ContentsGuide to Intelligent Fire Alarm Systems Intelligent Fire Alarm SystemsIntelligent Fire Alarm Systems Addressing Methods Decimal address switchesSystem Fault Tolerance Dedicated address programmerFire System Zones Intelligent Fire Alarm SystemsPRE-ALARM Facility Interface Modules Programming of Intelligent Fire Alarm PanelsRemote Leds Advantages of Intelligent SystemsFire System Categories GuideDetector Application Guide Category M SystemsApplication Guide Manual Call Points 1. Manual Call Point PositioningSelection of Automatic Fire Detectors Areas subject to rapid changes Fixed temperature detector 58CRate of rise heat detector During normal useDetector type Location and Spacing of Automatic Fire DetectorsCeiling Height To EN54-7 10.5m Heat detector conforming toSloping Ceilings CorridorsCorridor being 7.5m and 5.3m respectively Voids and False Ceilings Lantern LightsLocation and Spacing of Optical Beam Detectors Audible Alarm Signals Visual Alarm SignalsMaintenance of Fire Detectors Codes and standards in the UK BS5839 Part 12002, SectionIntelligent Product Range Series 200 Plus FeaturesGeneral Specifications Series 200 Plus Analogue Addressable Detector Range2251EM Photoelectric Smoke Sensor WeightSystem Sensor Intelligent Product Range 2251TEM PHOTO-THERMAL SensorDrift Compensation and Smoothing 5251REM, 5251EM and 5251HTEM Heat SensorsRemote Test Switch 6500S Beam DetectorLaser Detector Operating Temperature -10C to 55CWeight 142g With LED blink enabled 2251EIS Intrinsically Safe Detector and IST200 InterfaceB500 Series Bases Exterior diameter Weight 100gInterior diameter DepthM200 Series Module Range M200XE Short Circuit Isolator Module5A at 250VAC Specifications Max Standby Current, externally powered zoneM201E Output Module M210E-CZ Conventional Zone ModuleIndoor AccessoriesCall Points Indoor products are generally rated at IP24DSounder Strobes Audio Visual ProductsDetector Base Sounders Majority of back box formatsOther Information Avenue Hoch Paris, France Tel +33 1 53 89 00 Other InformationApproval Bodies for Fire Detection Products Jernholmen DK-2650 Hvidovre Denmark Tel +45 36 349Telephone + 7 095 Telephone + 91 124 System Sensor Fire DetectorsVolochaevskaya Str 40, Bld Fax + 7 095

BS5839 specifications

System Sensor BS5839 is a standard that pertains to fire detection and alarm systems, providing guidelines for the design, installation, and maintenance of these essential safety tools. It is crucial for safeguarding lives and property, ensuring that fire detection systems are effective and reliable. The BS5839 standard, established in the UK, covers a wide range of fire alarm system types, including conventional, addressable, and wireless systems.

One of the main features of BS5839 is its comprehensive classification of fire detection systems. The standard divides systems into categories based on the level of risk and the environment in which the system will operate. This classification helps ensure that the system installed meets the specific needs of the building and its occupants. For example, Category L systems are meant for life safety, while Category P systems are designed to protect property.

The technologies underpinning BS5839 include various types of detectors, alarm devices, and control panels. Smoke detectors, heat detectors, and multi-sensor detectors are prominent among the devices specified in the standard. Smoke detectors use photoelectric or ionization principles to detect smoke and signal an alarm, while heat detectors respond to temperature changes. Multi-sensor detectors combine both smoke and heat detection technologies to provide a more reliable response to fire conditions.

Another key characteristic of BS5839 is the emphasis on regular testing and maintenance. The standard outlines procedures to ensure that systems remain operational and effective over time. This includes routine system checks, functional testing, and more in-depth inspections at regular intervals. Ensuring that systems are maintained according to BS5839 is vital for compliance with insurance requirements and for safeguarding against potential legal liabilities.

Furthermore, BS5839 highlights the importance of staff training and awareness. It emphasizes that personnel responsible for fire safety must be adequately trained in the operation and response to fire alarm systems. This ensures that in the event of a fire, occupants are prompted to take appropriate action and evacuate safely.

In summary, System Sensor BS5839 provides a crucial framework for fire detection and alarm systems. Its classification of systems, incorporation of advanced technologies, and emphasis on maintenance all contribute to enhanced safety and compliance, protecting lives and property effectively.
Top Page Image Contents