Universal Security Instruments MICN109L, MICN102L warranty Electrical Shock Hazard

Page 7

•Good ventilation is recommended when household cleaning supplies or similar contaminants are used.

•Excessive spillage or reverse venting of fuel-burning appliances caused by outdoor ambient conditions, such as:

Wind direction and/or velocity, including high gusts of wind. Heavy air in the vent pipes (cold/ humid air with extended periods between cycles).

Negative pressure differential resulting from the use of exhaust fans.

Simultaneous operation of several fuel-burning appliances competing for limited internal air.

Vent pipe connections vibrating loose from clothes dryers, furnaces or water heaters.

Obstructions in or unconventional vent pipe designs which can amplify the above situations.

THIS ALARM WILL NOT WORK WITHOUT 120 VAC POWER AND A GOOD BATTERY PROPERLY INSTALLED. THE ALARM SHOULD BE TESTED WHEN INSTALLED AND THEN TESTED WEEKLY AFTER THAT.

INSTALLATION INSTRUCTIONS: CAUTION!! READ CAREFULLY.

Installation of this alarm must conform to the electrical codes in your area; Article 760 of the National Electrical Code, NFPA 72, 101; SBC (SBCCI); UBC (ICBO); NBC (BOCA): OTFDC (CABO), and any other local or building codes that may apply. Wiring and installation must be performed by a licensed electrician. Failure to follow these guidelines may result in injury or property damage.

This alarm must be powered by a 24-hour, 120V AC 60Hz circuit. Be sure the circuit cannot be turned off by a switch, dimmer or ground fault circuit interrupter. Failure to connect this alarm to a 24-hour circuit may prevent it from providing constant protection.

IMPORTANT: Do not subject this alarm to megger, high voltage or high-pot tests. Remove the

alarm(s) before high-potting tests occur on the circuit or system. (Ref. Section 550- 17, National Electric Code, 2002 Edition).

ELECTRICAL SHOCK HAZARD

Turn off power to the area where you will install this alarm at the circuit breaker or fuse box before beginning installation. Failure to turn off the power before installation may result in serious electrical shock, injury or death.

CAUTION: THIS SMOKE ALARM IS SEALED. THE COVER IS NOT REMOVABLE!

•A mounting bracket is provided on the back of the alarm.

•Remove the mounting bracket from the back of the alarm by holding the mounting bracket and twisting the alarm in the direction indicated by the "TWIST TO REMOVE" arrow on the side of the alarm base.

OPTIONAL TAMPER RESISTANT FEATURES: There are two separate tamper resistant locking features provided for this model. Activating one or both of these features deters someone from removing the smoke alarm from the mounting bracket or removing the battery from the alarm. The breakaway locking pins are clearly marked and molded into the mounting bracket. Refer to the diagram on the next page.

TO ACTIVATE THE LOCKING FEATURES: Do not activate the locking features until you have activated the battery, mounted the smoke alarm to the bracket and tested the smoke alarm. Refer to OPERATION, TESTING & MAINTENANCE instructions.

1.Detach the breakaway alarm locking pin from the mounting bracket.

ALARM/BRACKET

LOCKING PIN

BATTERY LOCKING PIN

Page 7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Table of Contents Alarm Limitations and Functions What YOU should Know about CO Where this Alarm should be InstalledWhat YOU should Know about Natural GAS Page Where YOU can Hear the Alarm from ALL Sleeping Areas Basic Safety InformationPage Electrical Shock Hazard Wires from Quick Connectorconnect to Wiring InstructionsDo not Tamper with Wires When Power is on OPERATION, Testing & Maintenance If the CO Alarm Sounds If Your CO and GAS Alarm SoundsWhat to do if Carbon Monoxide is Detected What to do if Natural GAS is Detected Using the Silence FeatureUsing the Test Feature Regular MaintenanceWeekly Testing Utha MaintenancePotential Sources of CO in the Home CO and Natural GAS Alarm LimitationsHOW can I Protect MY Family from CO POISONING? Repairs and ServicesDevelop and Practice a Plan of Escape Basics of Escape Plan FCC Part 15 Radio Frequency Devices What to do When the Alarm SoundsRecommendation Operational SummaryUltralife 9 Volt Battery Returns TEN Year Lithium Battery Limited WarrantyAlarm Returns

MICN109, MICN109L, MICN102, MICN102L specifications

Universal Security Instruments offers a versatile lineup of carbon monoxide and smoke detectors that provide essential safety features for any home or office environment. Among their popular models are the MICN102, MICN109L, MICN109, and MICN102L, each designed with advanced technology to ensure effective monitoring and protection against fire and carbon monoxide threats.

The MICN102 is a dual-sensor alarm, combining both smoke and carbon monoxide detection in a single unit. This compact device features an electrochemical sensor for precise CO detection, as well as an ionization smoke sensor that responds quickly to fast-flaming fires. With a loud alarm of 85 decibels, homeowners can rely on timely notifications in the event of emergencies. The MICN102 is also equipped with a test and silence button, allowing for easy routine checks and the ability to silence false alarms.

The MICN109L is an enhanced model that includes a voice alert feature. This model not only emits a loud alarm but also provides clear spoken alerts, indicating whether smoke or carbon monoxide has been detected, significantly improving user awareness and response times. With its user-friendly design, the MICN109L also has an easy-to-read display that shows the current CO levels, allowing users to stay informed about their indoor air quality.

The MICN109 shares many of the same core features found in the MICN109L, including the dual-sensor technology and 85-decibel alarm, but does not include the voice alert function. This model still offers reliable and efficient monitoring, making it an excellent choice for individuals looking for solid protection without additional features.

Lastly, the MICN102L combines the effective detection capabilities of the MICN102 with voice alerts similar to those in the MICN109L. This model is particularly beneficial for larger households or spaces where quick identification of the type of threat may be crucial. Features such as battery backup ensure continuous protection even during power outages, while the easy-to-install design allows for swift setup.

Across all models, Universal Security Instruments emphasizes user-friendly operation, reliability, and effective detection, providing peace of mind for families and individuals alike. With their modern design and advanced safety features, these units stand out as trusted guardians against fire and carbon monoxide hazards, reflecting Universal Security Instruments’ commitment to quality and safety.
Top Page Image Contents