SonicWALL 3500, NSA 5000, 4500 manual Configuring the Secondary Bridge Interface

Page 37

Configuring the Secondary Bridge Interface

Complete the following steps to configure the SonicWALL appliance:

1.Navigate to the Network > Interfaces page from the navigation panel.

2.Click the Configure icon in the right column of the X0 (LAN) interface.

3.In the IP Assignment drop-down, select Layer 2 Bridged Mode.

4.In the Bridged to drop-down, select the X1 interface.

5.Configure management options (HTTP, HTTPS, Ping, SNMP, SSH, User logins, or HTTP redirects).

Note: Do not enable Never route traffic on the bridge-pair unless your network topology requires that all packets entering the L2 Bridge remain on the L2 Bridge segments.

You may optionally enable the Block all non-IPv4 traffic setting to prevent the L2 bridge from passing non-IPv4 traffic.

If You Are Following

Proceed to Section:

Scenario...

 

 

 

C - L2 Bridge Mode

Additional Deployment Configuration

 

- page 37

 

 

Page 36 Configuring L2 Bridge Mode

Image 37
Contents Getting Started Guide SonicWALL NSA Getting Started Guide Document ContentsSonicWALL NSA Series BackThis Section Pre-Configuration TasksCheck Package Contents Administrator Information Obtain Configuration InformationObtain Internet Service Provider ISP Information Registration InformationFront Panel Back Panel Power Supply8 The Back Panel Registering Your Appliance on mysonicwall.com Before You Register Product Registration Registering and Licensing Your Appliance on mysonicwall.comService Bundles Licensing Security Services and SoftwareGateway Services Support ServicesSonicWALL NSA 5000/4500/3500 Getting Started Guide Registration Next Steps Registering a Second Appliance as a BackupDeployment Scenarios Selecting a Deployment Scenario ABCScenario a NAT/Route Mode Gateway Scenario B State Sync Pair in NAT/Route Mode Scenario C L2 Bridge Mode Connecting the WAN Port Initial SetupSystem Requirements Applying Power Connecting the LAN PortAccessing the Setup Wizard Accessing the Management InterfaceTesting Your Connection Connecting to Your NetworkActivating Licenses in SonicOS Upgrading Firmware on Your SonicWALL Saving a Backup Copy of Your PreferencesObtaining the Latest Firmware Upgrading the Firmware with Factory Defaults Upgrading the Firmware with Current SettingsUsing SafeMode to Upgrade Firmware On the System Settings page, click Upload New FirmwareConfirmation dialog box, click OK to proceed Uploaded Firmware NewInitial High Availability Setup Configuring a State Sync Pair in NAT/Route ModeScenario B Configuring Advanced HA Settings Configuring High AvailabilityNavigate to the High Availability Advanced 30 Configuring a State Sync Pair in NAT/Route Mode Synchronizing Settings Synchronizing Firmware Adjusting High Availability SettingsHA License Configuration Overview Click Register Associating Pre-Registered AppliancesConfiguring the Primary Bridge Interface Configuring L2 Bridge ModeConnection Overview IP Assignment drop-down, select Layer 2 Bridged Mode Configuring the Secondary Bridge InterfaceAdditional Deployment Configuration WAN DMZ Creating Network Access RulesSonicWALL NSA 5000/4500/3500 Getting Started Guide Creating a NAT Policy SonicWALL NSA 5000/4500/3500 Getting Started Guide Configuring Address Objects Leave Create a reflexive policy unchecked Configuring NAT PoliciesEnabling Gateway Anti-Virus Enabling Security Services in SonicOSSonicWALL NSA 5000/4500/3500 Getting Started Guide Security Services Gateway Anti-Virus page, click Accept Enabling Intrusion Prevention ServicesSecurity Services Intrusion Prevention page, click Accept Enabling Anti-Spyware Applying Security Services to Network Zones Configuring SonicPoint Provisioning Profiles Deploying SonicPoints for Wireless AccessUpdating SonicPoint Firmware 802.11g Radio tab Select Enable Radio Select Enable SonicPointConfiguring a Wireless Zone Assigning an Interface to the Wireless Zone Connecting the SonicPoint Using Packet Capture Troubleshooting Diagnostic ToolsUsing Ping Using the Active Connections Monitor Using Log View For this Task See this Chapter Deployment Configuration Reference ChecklistSupport and Training Options Customer Support Support ServicesKnowledge Portal SonicWALL Live Product DemosUser Forums Training Related Documentation Product Safety and Regulatory Information Lithium Battery Warning Safety and Regulatory InformationRack Mounting the SonicWALL Cable ConnectionsWeitere Hinweise zur Montage Safety and Regulatory Information in GermanHinweis zur Lithiumbatterie KabelverbindungenCanadian Radio Frequency Emissions Statement FCC Part 15 Class a NoticeCispr 22 EN 55022 Class a Regulatory Information for KoreaTrademarks Copyright Notice70 Notes SonicWALL NSA 5000/4500/3500 Getting Started Guide 72 Notes Rev a 01/08