TOA Electronics VFST-CMN-2 Operation and Care of Your Appliance, Cleaning and Servicing, Lhp

Page 13

OPERATION AND CARE OF YOUR APPLIANCE

1.Appliance operation may be controlled through the optional ON/OFF unit rocker switch, located in the lower control compartment, or through a remotely located optional wall switch or wall thermostat. Separate switches may provide independent control for the forced air blower and remote fireplace operation (op- tional equipment).

2.These heater rated units are equipped with a two stage (HI, LOW) gas control valve. To cycle the burner between the HI and LOW settings, rotate the control knob, located in the center of the valve front face, clockwise and counterclockwise respectively.

3.When lit for the first time, the appliance will emit a slight odor for an hour or two. This is due to the “burn-in” of the internal paints and lubricants used in the manufacturing process. Additionally, when lit for the first time, this appliance may produce smoke, this is normal and should be expected. For the first few hours, operate the appliance with doors and windows open to encourage the dissipation of smoke and fumes.

4.Upon each lighting of the appliance, con- densation may occur and fog the inside of the glass panel. This condition will disappear shortly as the appliance heats.

5.Keep lower control compartment clean by vacuuming or brushing at least twice a year. More frequent cleanings may be required due to excessive lint from carpeting, bedding ma- terials, etc. It is important that the control compartments, burners and circulating air pas- sageways of the heater be kept clean.

6.Always turn off gas to pilot before cleaning. Before relighting, refer to the lighting instruc- tions in this manual. Instructions are also found on a pull-out panel located on the floor of the appliance.

7.Always keep the appliance area clear and free from combustible materials, gasoline and other flammable liquids.

8.Remember, this appliance has a continuous burning pilot flame. Exercise caution when using products with combustible vapors.

CLEANING AND SERVICING

WARNING: TURN OFF THE UNVENTED GAS ROOM HEATER AND ALLOW TO COOL BEFORE CLEANING.

Only limited cleaning will be required under the normal use of the heater. Dust the front grate, the top of the piezo cover and the control knob occasionally. Do not use cleaning fluids to clean the logs or any other part of the room heater.

Remove the log assembly, gently handling by holding each log at each end. Use a vacuum cleaner to remove loose particles from the base and from around the burners. Gloves are rec- ommended to prevent the fibers from pricking your skin. If the skin is pricked, wash gently with soap and water. Replace the logs as de- tailed in Step 8 Assembling the Logs.

If, after a period of use, the flames start to exhibit unusual shapes and behavior, or the burners fail to ignite smoothly, then the burner holes may require some cleaning. If this hap- pens, it is preferable to contact your nearest dealer to get the appliance serviced.

REPLACEMENT PARTS

An exploded view of the room heater with numbered parts and a parts list can be found on page 19. All parts should be ordered through your Lennox distributor or dealer. Parts will be shipped at prevailing prices at time of order.

When ordering repair parts, always give the following information:

1.The model number of the heater.

2.The serial number of the heater.

3.The part number.

4.The description of the part.

5.The quantity required.

6.The installation date of the heater.

If you encounter any problems or have any questions concerning the installation of this heater, please contact your distributor. For the name of your nearest distributor contact:

LHP

1110 West Taft Avenue

Orange, CA 92865

NOTE: DIAGRAMS & ILLUSTRATION NOT TO SCALE.

ACCESSORIES AND COMPONENTS

Forced Air Kit

FAB-1100

 

RCL

Remote Control Kit

RCL-STAT

 

 

Rocker Switch Kit

FRS

Wall Switch Kit

FWSK

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Unvented Decorative Gas Fireplaces 903571 REV. H 12/2007 Consumer Retain this manual for future referenceTable of Contents Massachusetts And New York Require- ments CodesCombustion and Ventilation AIR MassachusettsClearances Location of FireplaceExample Assembly Steps PreinstallationInstallation Steps Check Gas TypeVfst Framing Specifications Vfst Appliance SpecificationsFraming Dimensions 40-1/8 1016 mm Min 22-3/4 578 mm43 1092 mm Min Gas Flex Line Kit, Model Gflv Finished Wall Details Vfst Series Standard Wiring DiagramFlame Appearance Assembling the LogsWall Switch Kit Remote Control KitInstalling the Optional Glass Door Optional EquipmentSolid Brass Hood Kit Optional on Unit Rocker SwitchSolid Brass Louver Kit Wall Thermostat KitReplacement Parts Cleaning and ServicingAccessories and Components Operation and Care of Your ApplianceKit Possible Cause Remedy Observed ProblemOperating Instructions For Your Safety Read Before LightingWhat to do if YOU Smell GAS Lighting InstructionsTurn Control Knob to Pilot Position Turn Control Knob to OFF Position PilotPilot Location Turn Control Knob to on PositionVFST-CMN Vfst Replacement Parts ListDescription Replacement Parts Vfst VFPF-CMN Vfpf Replacement Parts ListReplacement Parts Vfpf Page Page Orange, CA 903571 REV. H 12/2007

VFST-CMN-2 specifications

The TOA Electronics VFST-CMN-2 is a top-tier public address system speaker that epitomizes the fusion of technology and audio excellence. Renowned for its superior sound quality, this speaker is designed primarily for commercial, institutional, and outdoor environments. One of its standout features is its remarkable versatility, making it suitable for various applications, including schools, shopping centers, and outdoor events.

A key characteristic of the VFST-CMN-2 is its robust construction. Designed to withstand challenging conditions, the cabinet is made from high-impact ABS plastic, ensuring durability and longevity. This makes it an ideal choice for use in outdoor settings where exposure to the elements is a concern. Additionally, the speaker is equipped with a weather-resistant grille that helps protect the internal components from moisture and debris, further enhancing its suitability for external applications.

The VFST-CMN-2 also boasts an impressive frequency response, which allows it to deliver crystal-clear sound across a wide range of audio frequencies. Its ability to reproduce low, mid, and high frequencies ensures that announcements and music are clear and intelligible, making it an excellent choice for diverse audio needs. Complementing its sound capabilities, this speaker is equipped with high-efficiency drivers that maximize audio output while minimizing distortion.

Furthermore, the VFST-CMN-2 incorporates advanced technology that allows for easy installation and configuration. It features a dual voltage transformer that provides flexibility, enabling the speaker to operate at both 100V and 70V systems, catering to various installation requirements. The integrated mounting brackets make installation straightforward, allowing users to quickly position the speaker for optimal sound distribution.

The design of the VFST-CMN-2 also emphasizes aesthetics, maintaining a sleek and modern look that blends well with any environment. Its lightweight design facilitates mobility, allowing users to easily relocate the speaker as needed.

In conclusion, the TOA Electronics VFST-CMN-2 is a powerful and resilient speaker system that delivers exceptional performance across different settings. With its durable construction, superior audio quality, and user-friendly features, it stands out as a premier solution for any public address or sound reinforcement needs. Whether used in an educational institution, commercial space, or at an outdoor event, the VFST-CMN-2 ensures clear communication and an outstanding listening experience.
Top Page Image Contents