Guardian Technologies PN 8402 ENTRY/EXIT Delays, System Advisory Tones SAT’s, Display Windows

DISARMING

To disarm your system or to turn off an alarm, just enter your user code. Once again, if your system is connected to a monitoring service, be sure to cancel any accidental alarms to prevent emergency personnel from responding.

ENTRY/EXIT DELAYS

When you arm to the AWAY mode, there is a delay period to allow you time to exit the premises. Likewise, there is an entry delay time so you can enter the building and disarm the system before the alarm sounds. You should leave and return only through designated doors protected with delay sensors. The times for exit and entry delays have been recorded by your installer on the System Information pages.

During the entry delay, a “pre-alarm” tone will sound to remind you that the system is armed and must be either disarmed or re-armed. An alarm will occur at the end of the entry delay time if no action is taken.

0 When your system is set up for the “Interior Follower” feature, instant interior sensors become delay sensors if you first enter through your delay door. You can now walk in front of motion detectors on the way to the keypad after you enter.

SYSTEM ADVISORY TONES (SAT’s)

SAT’s are beeps that sound inside the home and are normally heard at arming and disarming. They indicate the arming status of the system, and will also advise you if a trouble message or an alarm memory has been displayed in the keypad’s windows. SAT’s will also sound when remote transmitters are used to arm or disarm the system.

1 beep = AWAY mode

2 beeps = STAY mode 2 sets of 2 beeps q NIGHT mode 3 beeps q Disarmed

4

Protest SAT’s: 4 quick beeps repeating every 45 seconds. These tones indicate that a trouble message or alarm has just been displayed in the master keypads windows. The keypad’s “Ready” light will also blink to indicate these conditions. See the

Master Keypad Reference Diagram for further information.

Press the * key to silence the protest SAT’s. The message will remain in the windows. If the windows are not cleared (see later sections), a set of protest SAT’s will follow the normal arm/disarm SAT’s whenever the system’s armed mode is changed. The protest SAT’s serve as a reminder that there is still a window message that has not been cleared or acted upon.

0 ARM/DISARM EXTERIOR CHIRPS

Your system may be set up to allow you to arm/disarm from outside using a hand- held transmitter. If so, the exterior alarm sirens will “chirp” (quick “pops”) in the same pattern as the interior SAT’s. These chirps allow you to verify the current system status without going inside. If trouble occurred while you were away (or if a previous message was not cleared), four protest chirps will be added to the end of the arm/disarm chirps.

BURGLARY VIOLATION BEEPS

For your protection, this system lets you know if a burglary alarm has occurred in your absence. If an alarm has occurred, warning beeps will sound over all speakers for three seconds. These violation beeps will immediately start when you enter the premises and trigger the entry pre-alarm. If you are using a handheld transmitter from outside the building and send a status request or disarm command, the warning will also sound.

Once the sirens stop, burglary alarms are also “remembered” in two other ways. The “Ready” light flashes rapidly and, if part of your system, selected house lights

ill come on and remain on.

CAUTION: Anytime a prior burglary alarm is indicated, you should leave the area immediately and contact the appropriate authorities. Do not go into the building.

From this point, all information applies to the master keypad. For quick reference, refer to the Master Keypad Reference Diagram.

DISPLAY WINDOWS

The display windows under the hardwire keypad door indicate a variety of system conditions. See the System Information pages for transmitter and/or hardwire zone locations.

CLEARING ALARM MEMORY

The cause of an alarm will be indentified in the display windows as soon as it occurs. To clear the memory, press and hold the * key until the second beep sounds. Protest beeps will be tagged onto the end of arm/disarm SAT’s until the alarm message is cleared.

5