First Alert fire and burglary partitioned security systems with scheduleing Using the 1 OFF Key

Page 36

Disarming And Silencing Alarms

Using the 1 OFF Key

The OFF key is used to disarm the system and to silence alarm and trouble sounds. See "SUMMARY OF AUDIBLE NOTIFICATION" section for information which will help you to distinguish between FIRE and BURGLARY alarm sounds.

IMPORTANT: If you return and the main burglary sounder is on, DO NOT enter the premises, but call the police from a nearby safe location. If you return after an alarm has occurred and the main sounder has shut itself off, the keypad will beep rapidly upon entering, indicating that an alarm has occurred during your absence. LEAVE IMMEDIATELY and CONTACT THE POLICE from a nearby safe location.

To disarm the system and silence burglary or fire alarms:

1. Enter your security code and press

DISARMED

READY TO ARM

OFF

1

.

2.The Ready message will be displayed (if no alarms have occurred while armed) and the keypad will beep once to confirm that the system is disarmed.

Memory of Alarm

The keypad displays the zone number and type of alarm for any zone that has an alarm condition. These messages will remain displayed until cleared by a user. If an alarm has occurred, note the zone number displayed on the keypad and repeat step 1 above to clear the "Memory of Alarm" and restore the Ready message display. If the Ready message will not display, go to the displayed zone and remedy the fault (close windows, etc.). If the fault cannot be remedied, notify the alarm agency.

If the system was armed when the alarm occurred, repeat step 1 twice: once to disarm the system, a second time to clear the display.

– 36 –

Page 35 Page 37
Image 36
Page 35 Page 37
Contents $&&$&% Table of Contents Trouble Conditions System Overview GeneralPartitioned System System Overview cont’d ZonesFire Protection Burglary ProtectionAlarms Memory of AlarmSpeed Key Macros Using Schedules Device TimersTo Access Another Partition Goto Command Self-Help Feature Phone Access & Voice Response CapabilityMaster Keypad Operation To view the abbreviated instructionsSystem Overview cont’d About The Keypads Alpha KeypadFunctions Of The Keypad Functions Of The Keypad cont’d Functions Of The Keypad cont’d Entry/Exit Delays General InformationSecurity Codes & Authority Levels Duress CodeQuick Arming Security Codes & Authority Levels cont’d Authority LevelsGeneral Rules on Authority Levels and Changes To view your authority level and system capabilitiesTo Exit User Edit Mode To Add a UserRF Button ? Limited Use User#84 Command To Change a Users CodeTo Delete a User Accessing Other Partitions To Access Another PartitionGlobal Arming To Goto another partitionAccessing Other Partitions cont’d Fault 002 Loading Dock Window Common Lobby Operation How User Codes Affect the Common Lobby Codes with Global ArmingCodes with Non-Global Arming Other Methods of Arming/Disarming Using Ready Key To show faulted zonesTypical fault display Checking For Open ZonesDisplaying All Zone Descriptors Using Bypass Key Bypassing Protection ZonesTo bypass zones, the system must be disarmed first To use the Quick Bypass feature Bypassing Protection Zones cont’dQuick Bypass Displaying Bypassed ZonesUsing the 3 Stay key Arming Perimeter OnlyWith Entry Delay OFF Using Instant KeyUsing the 2 Away Key Arming All ProtectionUsing Maximum Key Disarming And Silencing Alarms Using the 1 OFF KeyTo disarm the system and silence burglary or fire alarms Using The Keyswitch ArmingDisarming Chime Mode Using KeyViewing Central Station Messages Using Panic Keys Panic KeysSpeed Key Macros DefiningSpeed Key Macros cont’d ExecutingAccess Door Control Using #70 Relay Menu Mode To activate relays using a telephone and 4285 or 4286 VIPUsing #70 Relay Menu Mode cont’d To Exit Enter 00 NOWUsing Schedules Delaying the Closing TimeTo delay the closing time Temporary Open/Close SchedulesUsing Schedules cont’d Programming Temporary SchedulesTo program temporary schedules Using Schedules cont’d Days ? Mtwtfss HIT 0-7 X Programming Device Timers To enter the device timer menu modeProgramming Device Timers cont’d DAYS? Mtwtfss HIT 0-7 X Permanent ? Event Log Procedures To Display The Event LogSelect the partition Event Logging Procedures To Exit the Event LogTesting The System Using Test KeyTesting The System cont’d Testing Your SystemFire Alarm System Case Of Fire AlarmSilencing a Fire Alarm Fire Alarm System cont’d Fire Display LockFire Drill Test Code + # + Fire Alarm System cont’d Trouble Conditions Typical Trouble DisplaysCall for Service Immediately Trouble Conditions cont’dPower Failure Servicing InformationRecommendations For Proper Protection Recommendations For Smoke And Heat DetectorsRecommendations For Proper Protection cont’d Addition, we recommend the followingRecommendations For Proper Intrusion Protection Emergency Evacuation Replacing Batteries in Wireless Sensors Maintaining Your SystemTaking Care of Your System Silencing Low Battery Warning Tones at the Keypad Maintaining Your System cont’dRoutine Care Function Procedure Comments Quick Guide To System FunctionsQuick Guide To System Functions cont’d Summary Of Audible Notification Alpha Display KeypadsGlossary Federal Communications Commission FCC Part 15 Statement Federal Communications Commission FCC Part 68 Notice Canadian Department of Communications DOC Statement Limitations of this Alarm System Limitations of this Alarm System Index AwayLsens ¬19¢Ll

fire and burglary partitioned security systems with scheduleing specifications

First Alert is a trusted name in safety and security, consistently providing innovative solutions to protect homes and businesses. Their fire and burglary partitioned security systems are specifically designed to ensure comprehensive coverage against threats, offering users peace of mind. These systems utilize advanced technologies to deliver unparalleled performance.

One of the main features of First Alert fire and burglary security systems is the partitioning capability. This allows users to divide their property into separate zones or areas, each with its own security settings. For instance, during daytime, homeowners can enable security solely in specific areas, such as bedrooms and home offices, while keeping other regions like living rooms and kitchens unmonitored. This flexibility helps conserve energy and reduces false alarms, making the system more efficient.

Scheduling is another critical characteristic of First Alert systems. Users have the ability to create customized schedules for when the security system should be active or inactive. For example, a homeowner may set the system to turn on automatically in the evenings when they are away and to remain off during weekends when they are home. This programmable feature enhances user convenience and allows for tailored security solutions that fit individual lifestyles.

First Alert’s systems incorporate the latest technological advancements, including integrated smoke and carbon monoxide detectors. This multidimensional approach means that not only does the user benefit from burglary prevention, but they are also safeguarded against potential fire hazards. The sensors can communicate directly with a central hub, sending real-time alerts to homeowners’ smartphones in case of emergencies.

Moreover, First Alert integrates smart home compatibility, allowing users to connect their security system with various smart devices. This integration means homeowners can monitor their property remotely, receive notifications, and even take immediate action through mobile applications.

Overall, First Alert fire and burglary partitioned security systems stand out due to their unique combination of flexibility, scheduling capabilities, and advanced technology. These features are designed not just to deter potential threats but also to enhance the overall safety and security experience for users. With First Alert, homeowners can enjoy the reassurance that they are taking proactive steps to protect what matters most.
Top Page Image Contents